ISSN : 0970 - 020X, ONLINE ISSN : 2231-5039
     FacebookTwitterLinkedinMendeley

Determination of Physicochemical Properties and Fatty Acid Composition of "Kabate" Larva Oil from Timor Island

Febri Odel Nitbani, Hermania Em Wogo2, Titus Lapailaka1 and Beta Achromi Nurohmah2

1Department of Chemistry, Faculty of Science and Engineering, Universitas Nusa Cendana, Kupang, Indonesia.

2Department of Chemistry, Faculty of Mathematics and Natural Sciences, Universitas Gadjah Mada, Yogyakarta, Indonesia.

Corresponding Author E-mail: febri_nitbani@yahoo.com

DOI : http://dx.doi.org/10.13005/ojc/3402058

Article Publishing History
Article Received on : September 16, 2017
Article Accepted on : January 15, 2018
Article Metrics
ABSTRACT:

Kabate larva oils could be produced from its larva through Soxhlet extraction using n-hexane. Kabate larva, which locally in Timor Island called, can be found in the wounded stem of Sesbania gradiflora L. tree. In this work, the physicochemical properties and the fatty acid composition of Kabate larva oils were evaluated. Kabate larva oils was afforded as viscous yellow liquid with acid value, saponification value, peroxide number, iodine number, kinematic viscosity (at 100°C) and specific gravity (15°C) properties were 1.58 mg KOH/g; 111.28 mg KOH/g; 2.1554 meg/kg; 44.1426; 0.8159 g/mL; 40.57 mm2/s respectively. Based on the GC-MS analysis, it has been found out that fatty acids composition in Kabate larva oil were identified as a palmitic and oleic acid with a percentage value of 43.57 and 56.43% respectively.

KEYWORDS:

Kabate Larva Oil; Physicochemical Properties; Fatty Acid

Download this article as: 

Copy the following to cite this article:

Nitbani F. O, Wogo H. E, Lapailaka T, Nurohmah B. A. Determination of Physicochemical Properties and Fatty Acid Composition of "Kabate" Larva Oil from Timor Island. Orient J Chem 2018;34(2).


Copy the following to cite this URL:

Nitbani F. O, Wogo H. E, Lapailaka T, Nurohmah B. A. Determination of Physicochemical Properties and Fatty Acid Composition of "Kabate" Larva Oil from Timor Island. Orient J Chem 2018;34(2). Available from: http://www.orientjchem.org/?p=43891


Introduction

Indonesia is one of the world’s top biodiversity rich countries in both flora and fauna. Since ancient times, many ethnic groups of Indonesian traditional societies have used natural products for medical purposes. The facts show that the people of Timor Island traditionally still uses oil from Kabate larva to treat baby’s mouth infectious or oral thrush, which is caused by Candida albicans fungus. Oral thrush, or its locally called Gomak disease, is the appearance of thick white layers in the mouth and throat of infants that if it is not handled properly can cause to death. The Kabate larva, in a local language of Timor Island called, is a larva that can be found in the wounded stem of the Sesbania gradiflora L. tree as shown in Figures 1.

Figure 1: Kabate larva from Sesbania grandiflora L. tree

Figure 1: Kabate larva from Sesbania grandiflora L. tree


Click here to View figure

 

A review has reported that antimicrobial activity, as well as anti-fungal of the vegetable oils or animal fats, were not lead to by their triglyceride compositions but their monoacylglycerol (monoglyceride) of their fatty acids1. Some examples of monoacylglycerol from fatty acids that reported for having antimicrobial activity i.e. monolaurin from coconut oil2,3,4,5,6,7,8, monocaprin from coconut oil9, monomyristin and monolinolein10 and also monoolein11.

The facts that are how Timorese traditionally using Kabate larva oil for a treatment of oral thrush in the baby’s mouth indicates that its oils have an activity as antifungal against Candida albicans. It has been proposed that the Kabate larva oil has been converted into monoacylglycerol compounds in baby’s mouth so it has antifungal activity. However, until now there is no literature have been published regarding the composition of fatty acids and monoacylglycerol in Kabate larva oil. Therefore, this work will be carried out to isolate and determine of some physicochemical of Kabate larva oil. It will be also determined the type of fatty acids in the Kabate larva oil by Gas Chromatography-Mass Spectroscopy.

Experimental Methods

Materials

Materials used in this work were Kabate larva oil, sodium sulfate anhydrous, sodium thiosulfate, hydrochloric acid, glacial acetic acid, starch, potassium iodide, iodine-bromide reagent, phenolphthalein indicator, n-hexane, ethanol, chloroform, and distilled water. All of the reagents were pro analysis grade and purchased from Merck, except distilled water and Kabate larva oil.

Instruments

The instruments used in this study were glass equipment, Soxhlet extractor, and reflux apparatus set. Determination of fatty acid composition was carried out using Gas Chromatography-Mass Spectrometer (GC-MS, Shimadzu QP-2010).

Experimental Procedures

Isolation of Kabate larva oil

Kabate larva were prepared first by peeling the outer skin and its black dirt on the tail. The cleaned Kabate larva (100 g) was then wrapped in a filter paper which in both of the tops and bottom end was put on fatty free cotton. Put the wrapped Kabate larva in a Soxhlet extractor and added n-hexane to a round bottomed flask (60% of total volume of the flask) and performed the extraction for about 2 to 3 hours. Cool down the extract to room temperature and added Na2SO4 anhydrous to eliminate water. Filtered the extract and evaporated the solvent and collected the oils for further analysis.

Determination of Physicochemical Proprieties

Determination of Acid Value

Put a Kabate larva oil  (10 g) in a 250 mL flat-bottom round flask and added 25 mL 95% neutral alcohol (95% alcohol that had been titrated with 0.1 N KOH and turned to pink; using phenolphthalein indicator). The flasks were then fitted with condensate cooler and the mixture was heated to boil and strongly shaken out to dissolve its free fatty acids. The reaction product was cooled and subsequently titrated with a standardized 0.1 N KOH solution using phenolphthalein indicator. The titration process was stopped when the pink color remains for the 30s.  The acid value of the sample was calculated according to the following equation:

Equation 1

Determination of Saponification Value

A total of 1.0 g of Kabate larva oil was put in a 100 mL of flat-bottomed round flask. A total of 50 mL ethanolic KOH (4 g KOH/100 mL EtOH) was added and the flask was closed with a condensate cooler. The mixture was boiled for 30 minutes, cooled and added a few drops of phenolphthalein indicator. The solution was then titrated with a 0.5 N HCl standard solution. The titration was also performed to the blank solution. The saponification value was calculated by the following formula:

Equation 2

Where V is the volume of HCl used for titration and calculated by subtracting the total volume needed for titration of the blank solution and the sample (V HCl for blank – sample).

Determination of Peroxide Number

Peroxide number was determined by put 0.5 g of Kabate larva oil in a closed Erlenmeyer and added 30 mL glacial acetic acid-chloroform solution mixture (3:2). The mixture was then shaken well and added with saturated KI solution (0.5 mL) and after 1 min was added with 30 mL distilled water. The solution was then titrated with sodium thiosulfate 0.1 N until it turns into a pale yellow solution. To this solution, 0.5 mL 1% starch solution was added and titration continued until blue color disappear. Peroxide number was calculated by the following equation:

Equation 3

Determination of Iodine Number

Kabate larva oil sample (0.5 g) was put in a closed Erlenmeyer and added with chloroform (10 mL) and 25 mL of iodine-bromide reagents. The mixture was shaken and placed in a dark place for 30 minutes. To the mixture was added 10 mL 15% KI solution and 50 mL hot distilled water. The mixture was then titrated with sodium thiosulfate solution (Na2S2O3 0.1 N) until it turns to a pale yellow solution. To the solution was added 2 mL of starch solution and the titration was continued until the blue color disappeared. The blank solution was prepared by mixing 25 mL iodine-bromide reagent with 10 mL KI 15%.  This solution was diluted with 100 mL of hot distilled water before being titrated with sodium thiosulfate solution. Iodine number was calculated based on the following equation:

Equation 4

Where V Na2SO3 is a volume needed for titration and calculated by subtracting the total volume needed for titration the blank solution and the sample (V Na2S2O3 for blank – sample).

Determination of Specific Gravity

Determination of the specific gravity of the Kabate larva oil was carried out according to the procedure mentioned in ASTM D 1298

Determination of Kinematic Viscosity

The kinematic viscosity of Kabate larva oil was determined based on the procedures in ASTM D 445

Determination of Fatty Acid Using GC-MS

Conversion of fatty acids into its derivatives such as fatty acid ethyl ester is required so that it can be measured by Gas Chromatography-Mass Spectrometer (GC-MS) analysis. Kabate larva oil (25 g) and 50 mL of methanol was introduced into a flask that was equipped with a magnetic stirrer. To the mixture was added 2 ml of 16% sodium methoxide (b/v) solution. The mixture was then stirred for 45 minutes and monitored by Thin Layer Chromatography. After the completion of the reaction, the solvent was evaporated and the residue was dissolved in 50 mL petroleum ether, poured into separating funnel and washed with water until reach neutral pH. The organic layer was dried with anhydrous Na2SO4 and then the filtrate was evaporated. The residue was collected and analyzed by Gas Chromatography-Mass Spectrometer.

Results and Discussion

Kabate larva oil can be extracted from its larva using Soxhlet extractor and n-hexane as a solvent. Kabate larva oil afforded as viscous yellow liquid as seen in Figure 2 with a yield of 51%.

Figure 2: Kabate larva oil Figure 2: Kabate larva oil

Click here to View figure

 

The physical properties of Kabate larva oil were presented in Table 1. The physical properties of Kabate larva oil such as kinematic viscosities and specific gravity were determined according to the standard procedure (ASTM D 445 and 1298). Meanwhile, the chemical properties i.e. acid value, saponification value, peroxide numbers and iodine numbers were determined by titrimetric analysis.

Table 1: Physicochemical properties of Kabate larva oil

Parameters

Value

Acid value

1.58 mg KOH/gr

Saponification value

111.28 mg KOH/ gr

Peroxide number

2.1554 meg/kg

Iodine number

44.1426

Specific gravity (15 °C)

0.8159 gr/mL

Kinematic viscosity (100 °C)

40.57 mm2/s

 

Triglycerides, an ester of glycerol and fatty acids, are the main components in vegetable oils or animal fats, besides free fatty acids and other components. Triglycerides of a vegetable oil or animal fat bind to a particular fatty acid, saturated or unsaturated fatty acids, as an ester with glycerol. The composition of fatty acids can be determined using GC-MS but it required some preparation steps.

Fatty acids in a vegetable oil or animal fat have a very high boiling point. Hence, the fatty acids must be converted to fatty acid methyl esters so they can be analyzed using GC-MS. In this work, the composition of fatty acids in the Kabate larva oil may be determined by GC-MS as Fatty Acid Methyl Ester (FAME). Conversion of triglycerides from Kabate larva oil into their fatty acid methyl esters (FAME) was carried out through transesterification reactions.

Transesterification of Kabate larva oil was performed to convert fatty acids which bound to triglyceride ester to methyl ester. The transesterification reaction of Kabate larva oil was carried out using methanol and sodium methoxide catalyst at room temperature for 3.5 hours. The transesterification reaction of triglyceride into its FAME using methanol and the alkaline catalyst is called methanolysis. In this work, 16% sodium methoxide solution (b/v) in methanol was used as the basic catalyst. The sodium methoxide solution was prepared by reacting the sodium metal with absolute methanol at room temperature through an oxidation-reduction reaction. The transesterification reaction of the Kabate larva oil produced methyl ester as a light yellow liquid in the n-hexane phase. Meanwhile, the glycerol as side products of transesterification reaction was separated in the polar phase.

The Kabate larva oil methanolysis is preceded by the attack of methoxide ions on the carbonyl carbon atom of triglycerides and through the addition-elimination steps, it can be produced a methyl-methyl ester and glyceride ions. The methoxide ion can be recovered from the reaction of glyceride ion with methanol. This reaction could take place in reverse, so in order to obtain methyl ester products, it requires an excess of methanol. The mechanism of addition-elimination reaction of the methoxide ion to the carbonyl group of triglycerides may occur as in Figure 3.

Figure 3: Transesterification reaction mechanism of triglyceride

Figure 3: Transesterification reaction mechanism of triglyceride



Click here to View figure

 

The transesterification reaction product which was a mixture of methyl ester was then analyzed using GC-MS. The chromatogram and mass spectra were presented in Figure 4, Figure 5a and Figure 5b. Chromatogram of the transesterification products of Kabate larva oil (Figure 4) showed 2 peaks at a retention time (tR) of 33.91 and 37.24 min with a percentage value of 43.57 and 56.43% respectively.

Figure 4: Chromatogram of transesterification product of "Kabate" larva oil

Figure 4: Chromatogram of transesterification product of “Kabate” larva oil


Click here to View figure

 

The mass spectra of Figure 5a showed that the peak with a retention time of 33.91 min was methyl palmitate compound with the appearance of molecular ions (M+) at m/z = 270, which is corresponded to the molecular weight of methyl palmitate. Meanwhile, the mass spectra of the peak with tR 37.24 min (Figure 5b) showed a base peak at m/z = 55 and peak at m/z = 264. Even the result did not show any molecular ion (M+) at m/z = 296, this mass spectrum has 96% similarity index (SI ) with the data base indicate that the peak was methyl oleate. Fragments with m/z = 264 are formed due to the release of a methanol molecule ion (m/z = 32). Fragments with the greatest abundance and stable at m/z = 55 was a fragment with CH2CHCO structures.

Figure 5a: Mass spectra of peak at tR 33.91 min

Figure 5a: Mass spectra of peak at tR 33.91 min


Click here to View figure

 

Figure 5b: Mass spectra of peak at tR 37.24 min

Figure 5b: Mass spectra of peak at tR 37.24 min



Click here to View figure

 

Based on the GC-MS analysis, it can be concluded that the transesterification reaction of Kabate larva oils with methanol and alkaline catalysts produce methyl palmitate and methyl oleate. Thus, the fatty acids composition of the Kabate larva oil were palmitic acid and oleic acid with the percentage of 43.57 and 56.43% respectively.

Conclusion

Kabate larva oils were afforded in a viscous yellow liquid from an extract of Kabate larva by Soxhlet methods using n-hexane as a solvent with a yield of 51%.

The physicochemical properties of Kabate larva oil such as acid value, saponification value, peroxide number, iodine number, kinematic viscosity (100°C) and the specific gravity (15°C) were 1.58 mg KOH/g; 111.28 mg KOH/g; 2.1554 meg/kg; 44.1426; 0.8159 g/mL;  and 40.57 mm2/s respectively.

The types of fatty acids contained in Kabate larva oil were found to be palmitic acid and oleic acid with percentage composition of 43.57 and 56.43% respectively.

Acknowledgements

Authors showed gratitude to Ministry of Research, Technology, and Higher Education Indonesia for the financial support of this work through Hibah Penelitian Produk Terapan (PPT) T.A 2017.

References

  1. Nitbani, F.O.; Jumina, Siswanta, D.; Sholikhah, E.N. Int. J. Pharm. Sci. Rev. Res. 2015, 35 (1), 126-136
  2. Hierholzer, J.C; Kabara, J.J. J. Food Saf., 1972, 4, 1-12.
    CrossRef
  3. Chaibi, A.; Ababouch, L.; and Busta, F.  J. Food Prot. 1996, 59(7), 716–722.
    CrossRef
  4. Langone, M.A.P.; Dee Abreu, M.E.; Rezende, M.D.C; Sant’anna, G.L.J.R. Appl. Biochem. Biotechnol. 2002, 98–100
  5. Ugbogu O.C.; Onyeagba R.A.; Chigbu O.A. Afr. J.  Biotechnol.  2006, 5 (11), 1045-1047
  6. Hedge, B.M. Journal Indian Academy of Clinical Medicine, 2006, 7(1): 16-19
  7. Widiyarti G.; Hanafi M.; Soewarso W.P. Indo. J. Chem. 2009, 9 (1) : 99-106
  8. Nitbani, F.O.; Jumina, Siswanta, D.; Sholikhah, E.N.; and Fitriastuti, D. Orient. J. Chem., 2016, 32 (6), 1-8
  9. Nitbani, F.O.; Jumina, Siswanta, D.; Sholikhah, E.N. Int. J. Pharm. Sci. Rev. Res. 2015, 39 (1), 74-80
  10. Zhao, Y.; Liu J.; Deng L.; Wang, F.; Tan T. J. Mol. Catal. B: Enzym. 2011, 72, 157–162.
    CrossRef
  11. Wang, X.; Jina, Q.; Wang, T.; Huanga, J.; Wanga, X. J. Mol. Catal. B: Enzym. 2013, 97, 130-136.
    CrossRef


Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.