[1]
X. G. Fan et al., « Acceleration of globularization during interrupted compression of a two-phase titanium alloy », Mater. Sci. Eng. A, vol. 720, p.214‑224, mars 2018,.
DOI: 10.1016/j.msea.2018.02.026
Google Scholar
[2]
T. R. Bieler et S. L. Semiatin, « The origins of heterogeneous deformation during primary hot working of Ti–6Al–4V », Int. J. Plast., vol. 18, no 9, p.1165‑1189, sept. 2002,.
DOI: 10.1016/s0749-6419(01)00057-2
Google Scholar
[3]
J. H. Kim, S. L. Semiatin, et C. S. Lee, « Constitutive analysis of the high-temperature deformation of Ti–6Al–4V with a transformed microstructure », Acta Mater., vol. 51, no 18, p.5613‑5626, oct. 2003,.
DOI: 10.1016/s1359-6454(03)00426-9
Google Scholar
[4]
Y. Chong, T. Bhattacharjee, R. Gholizadeh, J. Yi, et N. Tsuji, « Investigation on the hot deformation behaviors and globularization mechanisms of lamellar Ti–6Al–4V alloy within a wide range of deformation temperatures », Materialia, vol. 8, p.100480, déc. 2019,.
DOI: 10.1016/j.mtla.2019.100480
Google Scholar
[5]
S. Roy et S. Suwas, « The influence of temperature and strain rate on the deformation response and microstructural evolution during hot compression of a titanium alloy Ti–6Al–4V–0.1B », J. Alloys Compd., vol. 548, p.110‑125, janv. 2013,.
DOI: 10.1016/j.jallcom.2012.08.123
Google Scholar
[6]
S. L. Semiatin, V. Seetharaman, et I. Weiss, « Flow behavior and globularization kinetics during hot working of Ti–6Al–4V with a colony alpha microstructure », Mater. Sci. Eng. A, vol. 263, no 2, p.257‑271, mai 1999,.
DOI: 10.1016/s0921-5093(98)01156-3
Google Scholar
[7]
Warchomicka, Canelo-Yubero, Zehetner, Requena, et Stark, « In-Situ Synchrotron X-Ray Diffraction of Ti-6Al-4V During Thermomechanical Treatment in the Beta Field », Metals, vol. 9, no 8, p.862, août 2019,.
DOI: 10.3390/met9080862
Google Scholar
[8]
I. Weiss, F. H. Froes, D. Eylon, et G. E. Welsch, « Modification of alpha morphology in Ti-6Al-4V by thermomechanical processing », Metall. Trans. A, vol. 17, no 11, p.1935‑1947, nov. 1986,.
DOI: 10.1007/bf02644991
Google Scholar
[9]
Z. X. Zhang, S. J. Qu, A. H. Feng, X. Hu, et J. Shen, « Microstructural mechanisms during multidirectional isothermal forging of as-cast Ti-6Al-4V alloy with an initial lamellar microstructure », J. Alloys Compd., vol. 773, p.277‑287, janv. 2019,.
DOI: 10.1016/j.jallcom.2018.09.220
Google Scholar
[10]
A. A. Korshunov et al., « Grain-structure refinement in titanium alloy under different loading schedules », J. Mater. Sci., vol. 31, no 17, p.4635–4639, (1996).
DOI: 10.1007/bf00366363
Google Scholar
[11]
L. Germain, N. Gey, M. Humbert, P. Bocher, et M. Jahazi, « Analysis of sharp microtexture heterogeneities in a bimodal IMI 834 billet », Acta Mater., vol. 53, no 13, p.3535‑3543, août 2005,.
DOI: 10.1016/j.actamat.2005.03.043
Google Scholar
[12]
N. Gey, P. Bocher, E. Uta, L. Germain, et M. Humbert, « Texture and microtexture variations in a near-α titanium forged disk of bimodal microstructure », Acta Mater., vol. 60, no 6, p.2647‑2655, avr. 2012,.
DOI: 10.1016/j.actamat.2012.01.031
Google Scholar
[13]
N. Gey, M. Humbert, M. J. Philippe, et Y. Combres, « Modeling the transformation texture of Ti-64 sheets after rolling in the β-field », Mater. Sci. Eng. A, vol. 230, no 1‑2, p.68–74, (1997).
DOI: 10.1016/s0921-5093(97)80111-6
Google Scholar
[14]
N. Gey, M. Humbert, M. J. Philippe, et Y. Combres, « Investigation of the α- and β- texture evolution of hot rolled Ti-64 products », Mater. Sci. Eng. A, vol. 219, no 1, p.80‑88, nov. 1996,.
DOI: 10.1016/s0921-5093(96)10388-9
Google Scholar
[15]
F. Montheillet, « Métallurgie en mise en forme à chaud », Tech. Ing. Matér. Métalliques, no M3031, (2009).
DOI: 10.51257/a-v1-m3031
Google Scholar
[16]
H. Geijselaers, C. Wang, A. Miroux, et V. Recina, « Use of Gleeble MAXStrain unit for study of damage development in hot forging », p.3, (2016).
Google Scholar
[17]
C. Zhang, M. Bellet, M. Bobadilla, H. Shen, et B. Liu, « A Coupled Electrical–Thermal–Mechanical Modeling of Gleeble Tensile Tests for Ultra-High-Strength (UHS) Steel at a High Temperature », Metall. Mater. Trans. A, vol. 41, no 9, p.2304‑2317, sept. 2010,.
DOI: 10.1007/s11661-010-0310-7
Google Scholar
[18]
R. Castro et L. Seraphin, « Contribution à l'étude métallographique et structurale de l'alliage de titane ta6v », Mém. Sci. Rev. Métallurgique, vol. 12, p.1025–1058, (1966).
Google Scholar
[19]
J. Xu, W. Zeng, D. Zhou, H. Ma, S. He, et W. Chen, « Analysis of flow softening during hot deformation of Ti-17 alloy with the lamellar structure », J. Alloys Compd., vol. 767, p.285‑292, oct. 2018,.
DOI: 10.1016/j.jallcom.2018.07.106
Google Scholar
[20]
R. Miller, « Flow softening during hot working of Ti-6Al-4V with a lamellar colony microstructure », Scr. Mater., vol. 40, no 12, p.1387‑1393, mai 1999,.
DOI: 10.1016/s1359-6462(99)00061-5
Google Scholar
[21]
S. L. Semiatin et G. D. Lahoti, « Deformation and unstable flow in hot forging of Ti-6Ai-2Sn-4Zr-2Mo-0.1Si », Metall. Trans. A, vol. 12, no 10, p.1705‑1717, oct. 1981,.
DOI: 10.1007/bf02643753
Google Scholar
[22]
A. Colin, « Hétérogénéités de déformation au cours du forgeage d'aubes en alliage de titane TA6V », thesis, Saint-Etienne, EMSE, (2007).
Google Scholar