Influence of areca nut nanofiller on mechanical and tribological properties of coir fibre reinforced epoxy based polymer composite

Document Type : Article

Authors

1 Department of Industrial Engineering and Management, Siddaganga Institute of Technology, Tumakuru-572102, India.

2 Department of Mechanical Engineering, Nitte Meenakshi Institute of Technology, Bengaluru, Yelahanka-560064, India.

3 Department of Mechanical Engineering, Sri Siddhartha Institute of Technology, Tumakuru, 572105, India.

Abstract

The present study is aimed at investigating the effect of incorporating arecanut nano filler on the tribological behaviour of coir reinforced epoxy based polymer matrix composite. Areca nut nano filler is produced by grinding followed by ball milling. Particle size analyzer confirmed the size of nano fillers obtained are in the range of 20-100 nm. Composites with different weight percentage of nano filler (0%, 5%, and 10%) were studied for their mechanical and tribological behaviour using pin on disc rig. Tensile, Flexural, Interlaminar shear and impact tests are carried out on the proposed composite. Taguchi’s technique is used for analysing effect of various factors on the tribological behaviour of the composite. The results showed that inclusion of arecanut nano filler enhanced the microhardness of the composite, with inclusion of arecanut filler the tensile strength increased up to 5 %, later there is a decrease in tensile strength. Flexural strength significantly increases with increase in filler percentage from 0% to 5%, but the variation of flexural strength from 5% to 10% is negligible. Inclusion of filler has negligible effect on the interlaminar shear strength of composites. Impact strength and wear resistance of the composite is enhanced with incorporation of filler.

Keywords

Main Subjects


References:
1. Shuhimi, F.F, Abdollah, M.F. Bin, Kalam, M.A., et al. "Tribological characteristics comparison for oil palm fibre/epoxy and kenaf fibre/epoxy composites under dry sliding conditions", Tribol. Int., 101, pp. 247-254 (2016).
2. Alves, C., Ferrao, P.M.C., Silva, A.J., et al. "Ecodesign of automotive components making use of natural jute fiber composites", J. Clean Prod., 18, pp. 313-327 (2010).
3. Faruk, O., Bledzki, A.K., Fink, H.P., et al. "Biocomposites reinforced with natural fibers: 2000-2010", Prog. Polym. Sci., 37, pp. 1552-1596 (2012).
4. Thomas, S., Paul, S.A., and Pothan, B.D., Natural Fibres: Structure, Properties and Applications. In: Susheel Kalia, B.S. Kaith IK, Ed. Cellul. Fibers Bio- Nano-Polymer Compos., Springer, Berlin, Heidelberg, pp. 3-42 (2011).
5. Pickering, K.L., Beckermann, G.W., Alam, S.N., et al. "Optimising industrial hemp fibre for composites", Compos. Part A Appl. Sci. Manuf., 38, pp. 461-468 (2007).
6. Joshi, S.V., Drzal, L.T., Mohanty, A.K., et al. "Are natural fiber composites environmentally superior to glass fiber reinforced composites?", Compos. Part A Appl. Sci. Manuf., 35, pp. 371-376 (2004).
7. Davoodi, M.M., Sapuan, S.M., Ahmad, D., et al. "Concept selection of car bumper beam with developed hybrid bio-composite material", Mater. Des., 32, pp. 4857-4865 (2011).
8. Ghavami, K., Toledo Filho, R.D., and Barbosa, N.P. "Behaviour of composite soil reinforced with natural fibres", Cem. Concr. Compos., 21, pp. 39-48 (1999).
9. Herrera-Franco, P.J. and Valadez-Gonzalez, A. "Mechanical properties of continuous natural fibrereinforced polymer composites", Compos. Part A Appl. Sci. Manuf., 35, pp. 339-345 (2004).
10. Brahmakumar, M., Pavithran, C., and Pillai, R.M. "Coconut fibre reinforced polyethylene composites: Effect of natural waxy surface layer of the fibre on fibre/matrix interfacial bonding and strength of composites", Compos. Sci. Technol., 65, pp. 563-569 (2005).
11. Rout, J., Misra, M., Tripathy, S.S., et al. "The influence of fibre treatment of the performance of coirpolyester composites", Compos. Sci. Technol., 61, pp. 1303-1310 (2001).
12. Khalil AHPS, Masri M., Saurabh, C.K., et al. "Incorporation of coconut shell based nanoparticles in kenaf/ coconut fibres reinforced vinyl ester composites", Mater. Res. Express, 4, p. 035020 (2017).
13. Basavarajappa, S., Arun, K.V., and Davim, J.P. "Effect of filler materials on dry sliding wear behavior of polymer matrix composites-A taguchi approach", Mater. Charact., 8, pp. 379-391 (2009).
14. Syahrullail, S., Izhan, M.I., and Rafiq, A.K.M.  Tribological investigation of RBD palm olein in different sliding speeds using pin-on-disk tribotester", Sci. Iran. Trans. Mech. Eng., 21, pp. 162-170 (2014).
15. Farhanah, A., Syahrullail, S. and Bahru, J. "Tribological behavior of refined, bleached and deodorized palm kernel as an alternative lubricant", Sci. Iran. Trans. Mech. Eng., 25, pp. 1169-1178 (2018).
16. Osterle, W., Dmitriev, A.I, Wetzel, B., et al. "The role of carbon fibers and silica nanoparticles on friction and wear reduction of an advanced polymer matrix composite", Mater. Des., 93, pp. 474-484 (2016).
17. Rostamiyan, Y., Fereidoon, A., Rezaeiashtiyani, M., et al. "Experimental and optimizing  flexural strength of epoxy-based nanocomposite: Effect of using nano silica and nano clay by using response surface design methodology", Mater. Des., 69, pp. 96-104 (2015).
18. Dmitriev, A.I., Hausler, I., Osterle, W., et al. "Modeling of the stress-strain behavior of an epoxy-based nanocomposite filled with silica nanoparticles", Mater. Des., 89, pp. 950-956 (2016).
19. Sebastian, S., Lothar, K., and Schettler F. "Nanoparticle reinforced epoxy gelcoats for fiber-plastic composites under multiple load", Process. Org. Coatings, 77, pp. 1129-1136 (2014).
20. Suresha, B., Chandramohan, G., Prakash, J.N., et al. "The role of fillers on friction and slide wear characteristics in glass-epoxy composite systems", J. Miner Mater. Charact. Eng., 5, pp. 87-101 (2006).
21. Briscoe, B.J., Pogosian, A.K., and Tabor, D. "The friction and wear of high density polythene: The action of lead oxide and copper oxide fillers", Wear, 27, pp. 19-34 (1974).
22. Tanaka, K. and Kawakami, S. "Effect of various fillers on the friction and wear of polytetra uoroethylenebased composites", Wear, 79, pp. 221-234 (1982).
23. Bahadur, S. and Tabor, D. "Role of fillers in the friction and wear behavior of high-density polyethylene.", Polym. Wear Its Control, 287, pp. 253-268 (1985).
24. Kishore, Sampathkumaran, P., Seetharamu, S., et al. "SEM observations of the effects of velocity and load on the sliding wear characteristics of glass fabric-epoxy composites with different fillers", Wear, 237, pp. 20- 27 (2000).
25. Liu, Y., Ma, Y., Che, J., et al. "Natural fibre reinforced non-asbestos organic non-metallic friction composites: Effect of abaca fibre on mechanical and tribological behaviour", Mater. Res. Express, 5, p. 055101 (2018).
26. Dhanalakshmi, S., Ramadevi, P., and Basavaraju, B. "Areca fiber reinforced epoxy composites: Effect of chemical treatments on impact strength", Oriental Journal of Chemistry, 4, pp. 409-418 (2015).
27. Hassan, M.M., Wagner, M.H., Zaman, H.U., et al. "Physico-mechanical performance of hybrid betel nut (areca catechu) short fiber/seaweed polypropylene composite", J. Nat. Fibers, 7, pp. 165-177 (2010).
28. Ross, P.J., Taguchi Techniques for Quality Engineering, New Delhi: Tata McGraw Hill Publishing Company Limited (2008).
29. Basavarajappa, S., Chandramohan, G., Mahadevan, A., et al. "Influence of sliding speed on the dry sliding wear behaviour and the subsurface deformation on hybrid metal matrix composite", Wear, 262, pp. 1007- 1012 (2007).
30. Agarwal, B.D., Analysis and Performance of Fiber Composites., 2nd Ed., John Wiley and Sons, Inc (1990).