Influence of bladed and glazed entrance on the performance of solar air heater

Document Type : Article

Authors

1 Faculty of Engineering, Tanta University, Tanta, Egypt.

2 Faculty of Engineering, Kafrelsheikh University, Kafrelsheikh, Egypt.; Higher Institute of Engineering and Technology, HIET, Kafrelsheikh, Egypt

3 Faculty of Engineering, Kafrelsheikh University, Kafrelsheikh, Egypt.

Abstract

The performance of a flat plate single-pass solar air heater (SAH) modified at the entrance region of the heater was experimentally investigated. The entrance region was covered with glass cover instead of steel cover. The aim of using glass at the entrance region is increasing the heating area exposed to solar irradiation. In addition, replacing the steel cover with glass reduces the shading effect occurred due to steel which decreases the temperature of the surface of the absorber and hence the outlet temperature of the air. Also, guide blades were placed in the entry region to ensure well air distribution on the absorber surface and hence enhancing the thermal performance of SAH. The modified SAH was compared with another one without air blades and without glass cover at the entrance. The experiments were performed at four air flow rates ranged from 0.013 kg/sec to 0.04 kg/sec. The modifications led to good enhancement in both the air temperature difference and the efficiency. The glazed-bladed SAH showed a good improvement in the daily thermal efficiency by 6.72 % to 10.5 % over the conventional heater and by 2.16 % to 3.25 % over the glazed SAH.

Keywords

Main Subjects

References

References:
1. Kabeel, A.E., Hamed, M.H., Omara, Z.M., and Kandeal, A.W. "Solar air heaters: Design configurations, improvement methods and applications - A detailed review", Renew. Sustain. Energy Rev., 70, pp. 1189- 1206 (2017).
2. Sharma, N., Bhat, I.K., and Grover, D. "Optimization of a smooth  at plate solar air heater using stochastic iterative perturbation technique", Sol. Energy, 85(9), pp. 2331-2337 (2011).
3. Baritto, M. and Bracamonte, J. "A dimensionless model for the outlet temperature of a nonisothermal  at plate solar collector for air heating", Sol. Energy, 86(1), pp. 647-653 (2012).
4. Bracamonte, J. and Baritto, M. "Optimal aspect ratios for non-isothermal  at plate solar collectors for air heating", Sol. Energy, 97, pp. 605-613 (2013).
5. Abdullah, A.S., El-samadony, Y.A.F., and Omara, Z.M. "Performance evaluation of plastic solar air heater with different cross sectional configuration", Appl. Therm. Eng., 121, pp. 218-223 (2017).
6. Chabane, F., Moummi, N., and Benramache, S. "Experimental study of heat transfer and thermal performance with longitudinal fins of solar air heater", J. Adv. Res., 5(2), pp. 183-192 (2014).
7. Alta, D., Bilgili, E., Ertekin, C., and Yaldiz, O. "Experimental investigation of three different solar air heaters: Energy and exergy analyses", Appl. Energy, 87(10), pp. 2953-2973 (2010).
8. Omojaro, A.P. and Aldabbagh, L.B.Y. "Experimental performance of single and double pass solar air heater with fins and steel wire mesh as absorber", Appl. Energy, 87(12), pp. 3759-3765 (2010).
9. Rai, S., Chand, P., and Sharma, S.P. "An analytical investigations on thermal and thermohydraulic performance of offset finned absorber solar air heater", Sol. Energy, 153, pp. 25-40 (2017).
10. Naphon, P. "On the performance and entropy generation of the double-pass solar air heater with longitudinal fins", Renew. Energy, 30(9), pp. 1345-1357 (2005).
11. Ho, C.D., Yeh, H.M., Cheng, T.W., Chen, T.C., and Wang, R.C. "The influences of recycle on performance of baffled double-pass  at-plate solar air heaters with internal fins attached", Appl. Energy, 86(9), pp. 1470- 1478 (2009).
12. Yeh, H.M. "Upward-type  at-plate solar air heaters attached with fins and operated by an internal recycling for improved performance", J. Taiwan Inst. Chem. Eng., 43(2), pp. 235-240 (2012).
13. Ho, C.D., Chang, H., Wang, R.C., and Lin, C.S. "Performance improvement of a double-pass solar air heater with fins and baffles under recycling operation", Appl. Energy, 100, pp. 155-163 (2012).
14. Priyam, A. and Chand, P. "Thermal and thermohydraulic performance of wavy finned absorber solar air heater", Sol. Energy, 130, pp. 250-259 (2016).
15. Gao, W., Lin, W., Liu, T., and Xia, C. "Analytical and experimental studies on the thermal performance of cross-corrugated and  at-plate solar air heaters", Appl. Energy, 84(4), pp. 425-441 (2007).
16. Karim, M.A. and Hawlader, M.N.A. "Performance investigation of  at plate, v-corrugated and finned air collectors", Energy, 31(4), pp. 452-470 (2006).
17. El-Sebaii, A.A., Aboul-Enein, S., Ramadan, M.R.I., Shalaby, S.M., and Moharram, B.M. "Thermal performance investigation of double pass-finned plate solar air heater", Appl. Energy, 88(5), pp. 1727-1739 (2011).
18. Gawande, V.B., Dhoble, A.S., Zodpe, D.B., and Chamoli, S. "Experimental and CFD investigation of convection heat transfer in solar air heater with reverse L-shaped ribs", Sol. Energy, 131, pp. 275-295 (2016).
19. Hans, V.S., Saini, R.P., and Saini, J.S. "Heat transfer and friction factor correlations for a solar air heater duct roughened artificially with multiple v-ribs", Sol. Energy, 84(6), pp. 898-911 (2010).
20. Sharma, S.K. and Kalamkar, V.R. "Experimental and numerical investigation of forced convective heat transfer in solar air heater with thin ribs", Sol. Energy, 147, pp. 277-291 (2017).
21. Boulemtafes-boukadoum, A., Benzaoui, A., and Nedjari, H.D. "Comparative study of the effects of two types of ribs on thermal performance of solar air heaters", Sci. Iran., 24, pp. 2418-2428 (2017).
22. Handoyo, E.A. and Ichsani, D. "Numerical studies on the effect of delta-shaped obstacles' spacing on the heat transfer and pressure drop in v-corrugated channel of solar air heater", Sol. Energy, 131, pp. 47-60 (2016).
23. Kulkarni, K., Afzal, A., and Kim, K. "Multi-objective optimization of solar air heater with obstacles on absorber plate", Sol. Energy, 114, pp. 364-377 (2015).
24. Yadav, S. and Kaushal, M. "Exergetic performance evaluation of solar air heater having arc shape oriented protrusions as roughness element", Sol. Energy, 105, pp. 181-189 (2014).
25. Pandey, N.K. and Bajpai, V.K. "Experimental investigation of heat transfer augmentation using multiple arcs with gap on absorber plate of solar air heater", Sol. Energy, 134, pp. 314-326 (2016).
26. Behura, A.K., Prasad, B.N., and Prasad, L. "Heat transfer, friction factor, and thermal performance of three sides artificially roughened solar air heaters", Sol. Energy, 130, pp. 46-59 (2016).
27. Prasad, B.N., Behura, A.K., and Prasad, L. "Fluid  flow and heat transfer analysis for heat transfer enhancement in three sided artificially roughened solar air heater", Sol. Energy, 105, pp. 27-35 (2014).
28. Krishnananth, S.S. and Kalidasa Murugavel, K. "Experimental study on double pass solar air heater with thermal energy storage", J. King Saud Univ. - Eng. Sci., 25(2), pp. 135-140 (2012).
29. Alkilani, M.M., Sopian, K., Mat, S., and Alghoul, M.A. "Output air temperature prediction in a solar air heater integrated with phase change material", Eur. J. Sci. Res., 27(3), pp. 3334-41 (2009).
30. Moradi, R., Kianifar, A., and Wongwises, S. "Optimization of a solar air heater with phase change materials: Experimental and numerical study", Exp. Therm. Fluid Sci., (2017). doi: http://dx.doi.org/10.1016/ j.exptherm usci .2017.07.011.
31. Kabeel, A.E., Khalil, A., Shalaby, S.M., and Zayed, M.E. "Improvement of thermal performance of the finned plate solar air heater by using latent heat thermal storage", Appl. Therm. Eng., 123, pp. 546- 553 (2017).
32. Kabeel, A.E., Khalil, A., Shalaby, S.M., and Zayed, M.E. "Experimental investigation of thermal performance of  at and v-corrugated plate solar air heaters with and without PCM as thermal energy storage", Energy Convers. Manag., 113, pp. 264-272 (2016).
33. El-Sebaii, A.A. and Al-Snani, H. "Effect of selective coating on thermal performance of  at plate solar air heaters", Energy, 35(4), pp. 1820-1828 (2010).
34. Aboul-Enein, S., El-Sebaii, A.A., Ramadan, M.R.I., and El-Gohary, H.G. "Parametric study of a solar air heater with and without thermal storage for solar drying applications", Renew. Energy, 21(3-4), pp. 505- 522 (2000).
35. Ramani, B.M., Gupta, A., and Kumar, R. "Performance of a double pass solar air collector", Sol. Energy, 84(11), pp. 1929-1937 (2010).
36. Dissa, A.O., Ouoba, S., Bathiebo, D., and Koulidiati, J. "A study of a solar air collector with a mixed 'porous' and 'non-porous' composite absorber", Sol. Energy, 129, pp. 156-174 (2016).
37. Chouksey, V.K. and Sharma, S.P. "Investigations on thermal performance characteristics of wire screen packed bed solar air heater", Sol. Energy, 132, pp. 591-605 (2016).
38. Prasad, S.B., Saini, J.S., and Singh, K.M. "Investigation of heat transfer and friction characteristics of packed bed solar air heater using wire mesh as packing material", Sol. Energy, 83(5), pp. 773-783 (2009).
39. Zheng, W., Zhang, H., You, S., Fu, Y., and Zheng, X. "Thermal performance analysis of a metal corrugated packing solar air collector in cold regions", Appl. Energy, 203, pp. 938-947 (2017).
40. Bayrak, F., Oztop, H.F., and Hepbasli, A. "Energy and exergy analyses of porous baffles inserted solar air heaters for building applications", Energy Build., 57, pp. 338-345 (2013).
41. Karsli, S. "Performance analysis of new-design solar air collectors for drying applications", Renew Energy , 32(10), pp. 1645-1660 (2007).
42. Holman, J.P., Experimental Method for Engineers, 8th Edn., p. 64, McGraw-Hill (2012).
43. Srithar, K. and Mani, A. "Studies on solar  at plate collector evaporation systems for tannery effluent (soak liquor)", Journal of Zhejiang University-Science A, 7(11), pp. 1870-1877 (2006).
Scientia Iranica
Volume 26, Issue 3
Transactions on Mechanical Engineering (B)
May and June 2019
Pages 1388-1399

Files

Share

How to cite

Statistics