Abstract
In thermal systems such as solar thermal and waste heat recovery systems, the available energy supply does not usually coincide in time with the process demand. Hence some form of thermal energy storage (TES) is necessary for the most effective utilization of the energy source. This study deals with the experimental evaluation of thermal performance of a packed bed latent heat TES unit integrated with solar flat plate collector. The TES unit contains paraffin as phase change material (PCM) filled in spherical capsules, which are packed in an insulated cylindrical storage tank. The water used as heat transfer fluid (HTF) to transfer heat from the solar collector to the storage tank also acts as sensible heat storage material. Charging experiments were carried out at varying inlet fluid temperatures to examine the effects of porosity and HTF flow rate on the storage unit performance. The performance parameters such as instantaneous heat stored, cumulative heat stored, charging rate and system efficiency are studied. Discharging experiments were carried out by both continuous and batchwise processes to recover the stored heat, and the results are presented.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Ananthanarayanan, V., Sahai, Y., Mobley, C.E., Rapp, R.A., 1987. Modeling of fixed bed heat storage units utilizing phase-change materials. Metallurgical Trans. B, 18:339–346.
Bansal, N.K., Buddhi, D., 1992. Performance equation of a collector cum storage using phase change materials. Solar Energy, 48(3):185–194. [doi:10.1016/0038-092X(92)90137-Y]
Barba, A., Spiga, M., 2003. Discharge mode for encapsulated PCMs in storage tanks. Solar Energy, 74(2):141–148. [doi:10.1016/S0038-092X(03)00117-8]
Beasley, D.E., Ramanarayanan, C., 1989. Thermal response of a packed bed of spheres containing a phase change material. Int. J. Energy Research, 13:253–265.
Bellecci, C., Conti, M., 1993. Phase change thermal storage: transient behaviour analysis of a solar receiver/storage module using the enthalpy method. Int. J. Heat Mass Transfer, 36(8):2157–2163. [doi:10.1016/S0017-9310(05)80146-2].
Chen, S.L., Yue, J.S., 1991. Thermal performance of cool storage in packed capsules for air-conditioning. Heat Recovery Systems & CHP, 11(6):551–561. [doi:10.1016/0890-4332(91)90057-B]
Cho, K., Choi, S.H., 2000. Thermal characteristics of paraffin in a spherical capsule during freezing and melting processes. Int. J. Heat Mass Transfer, 43(17):3183–3196. [doi:10.1016/S0017-9310(99)00329-4]
Esen, M., Durmu, A., Durmu, A., 1998. Geometric design of solar-aided latent heat store depending on various parameters and phase change materials. Solar Energy, 62(1):19–28. [doi:10.1016/S0038-092X(97)00104-7]
Ettouney, H., El-Dessouky, H., Al-Ali, A., 2005. Heat transfer during phase change of paraffin wax stored in spherical shells. ASME J. Solar Energy Engg., 127(3):357–365. [doi:10.1115/1.1850487]
Fouda, A.E., Despault, G.J.G., Taylor, J.B., Capes, C.E., 1984. Solar storage systems using salt hydrate latent heat and direct contact heat exchange-II characteristics of pilot system operating with sodium sulphate solution. Solar Energy, 32(1):57–65. [doi:10.1016/0038-092X(84)90049-5]
Ghoneim, A.A., Klein, S.A., 1989. The effect of phase-change material properties on the performance of solar air-based heating systems. Solar Energy, 42(6):441–447. [doi:10.1016/0038-092X(89)90044-3]
He, B., Martin, V., Setterwall, F., 2004. Phase transition temperature ranges and storage density of paraffin wax phase change materials. Energy, 29(11):1785–1804. [doi:10.1016/j.energy.2004.03.002]
Hoogendoorn, C.J., Bart, G.C.J., 1992. Performance and modelling of latent heat stores. Solar Energy, 48(1):53–58. [doi:10.1016/0038-092X(92)90176-B]
Ismail, K.A.R., Stuginsky, R., 1999. A parametric study on possible fixed bed models for pcm and sensible heat storage. Appl. Thermal Eng., 19(7):757–788. [doi:10.1016/S1359-4311(98)00081-7]
Ismail, K.A.R., Henriquez, J.R., 2002. Numerical and experimental study of spherical capsules packed bed latent heat storage system. Appl. Thermal Eng., 22(15):1705–1716. [doi:10.1016/S1359-4311(02)00080-7]
Mehling, H., Cabeza, L.F., Hippeli, S., Hiebler, S., 2003. PCM-module to improve hot water heat stores with stratification. Renewable Energy, 28(5):699–711. [doi:10.1016/S0960-1481(02)00108-8]
Prudhomme, M., Nguyen, T.H., Nguyen, D.L., 1989. A heat transfer analysis of solidification of slabs, cylinders and spheres. ASME J. Heat Transfer, 111:699–705.
Saitoh, T., Hirose, K., 1986. High performance phase-change thermal energy storage using spherical capsules. Chemical Engg. Commun., 41:39–58.
Sozen, M., Vafai, K., Kennedy, L.A., 1991. Thermal charging and discharging of sensible and latent heat storage packed beds. AIAA J. Thermophysics, 5(4):623–625.
Trp, A., 2005. An experimental and numerical investigation of heat transfer during technical grade paraffin melting and solidification in a shell-and-tube latent thermal energy storage unit. Solar Energy, 79(6):648–660. [doi:10.1016/j.solener.2005.03.006]
Author information
Authors and Affiliations
Additional information
Project supported by Sri Venkateswara college of Engineering, India.
Rights and permissions
About this article
Cite this article
Nallusamy, N., Sampath, S. & Velraj, R. Study on performance of a packed bed latent heat thermal energy storage unit integrated with solar water heating system. J. Zhejiang Univ. - Sci. A 7, 1422–1430 (2006). https://doi.org/10.1631/jzus.2006.A1422
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1631/jzus.2006.A1422
Key words
- Charging
- Discharging
- Heat transfer fluid (HTF)
- Latent heat
- Phase change material (PCM)
- Packed bed
- Thermal energy storage (TES)