Abstract
Many polymeric materials, including structural adhesives, exhibit anonlinear viscoelastic response. The nonlinear theory of Knauss and Emri(Polym. Engrg. Sci. 27, 1987, 87–100) is based on the Doolittle conceptthat the ‘free volume’ controls the mobility of polymer molecules and,thus, the inherent time scale of the material. It then follows thatfactors such as temperature and moisture, which change the free volume,will influence the time scale. Furthermore, stress-induced dilatationwill also affect the free volume and, hence, the time scale. However,during this investigation, dilatational effects alone were found to beinsufficient for describing the response of near pure shear tests of abisphenol A epoxy with amido amine hardener. Thus, the free volumeapproach presented here has been modified to include distortionaleffects in the inherent time scale of the material. The same was foundto be true for a urethane adhesive.
The small strain viscoelastic responses of the two materials havebeen determined from master curves of uniaxial and bulk creep testing atvarious temperatures. The nonlinear free volume model, modified toinclude distortional effects in the reduced time, was incorporated inthe ABAQUS finite element code via a user-defined material subroutine.For the epoxy, validation of the modified theory (a strain-basedformulation of free volume) has been achieved through good agreementbetween the computational and experimental results of butterfly-shapedArcan specimens subjected to loadings ranging from near pure shear toshear with various amounts of superposed tension and compression. Inaddition to predicting the response under a variety of multiaxial stressstates, the modified free volume theory also accurately predicts theformation and growth of shear banding, or regions of highly localizeddeformation, which have been found to occur upon continued loading ofthe epoxy. The urethane did not appear to exhibit any localizeddeformation over the range of temperatures at which it was tested.As a result, a stress-based modified free volume approach was requiredto model its multiaxial and temperature-dependent behavior. Althoughfree volume was the unifying parameter for the two materials, the needfor a stress-based and strain-based formulation of the free volume forthe urethane and epoxy, respectively, could not be reconciled at thistime.
This is a preview of subscription content, log in via an institution to check access.
Similar content being viewed by others
References
Argon, A.S., ‘A theory for the low-temperature plastic deformation of glassy polymers’, Philos.Mag. 28, 1973, 839–865.
Arruda, E.M. and Boyce, M.C., ‘Evolution of plastic anisotropy in amorphous polymers during finite straining’, Internat. J. Plasticity 9, 1993, 697–720.
Bauwens, J.C., ‘Yield condition and propagation of Luders’ lines in tension-torsion experiments of Poly(vinly Chloride)’, J. Polym. Sci.: Part A-2 8, 1970, 893–901.
Beebe, C., ‘Experimental methods for durability predictions of adhesively bonded joints in humid environments’, Master’s Thesis, The University of Texas at Austin, 1992.
Bowden, P.B., ‘The yield behavior of glassy polymers’, in The Physics of Glassy Polymers, R.N. Haward (ed.), Applied Science Publishers, London, 1973, 279–339.
Bowden, P.B. and Jukes, J.A., ‘The plastic yield behavior of Polymethylmethacrylate’, J. Mater. Sci. 3, 1968, 183–190.
Bowden, P.B. and Jukes, J.A., ‘The plastic flow of isotropic polymers’, J. Mater. Sci. 7, 1972, 52–63.
Boyce, M.C., Parks, D.M. and Argon, A.S., ‘Large inelastic deformation of glassy polymers. Part I: Rate dependent constitutive model; Part II: Numerical simulation of hydrostatic extrusion’, Mech. Mater. 7, 1988, 15–33, 35–47.
Boyce, M.C., Arruda, E.M. and Jayachandran, R., ‘The large strain compression, tension, and simple shear of polycarbonate’, Polym. Engrg. Sci. 34, 1994, 716–725.
Doolittle, A.K., ‘Studies in Newtonian flow. II. The dependence of the viscosity of liquids on freespace’, J. Appl. Mech. 22, 1951, 1471–1475.
Doolittle, A.K., ‘Studies on Newtonian flow. V. Further verification of the free-space viscosity equation’, J. Appl. Mech. 28, 1957, 901–905.
Ferry, J.D., Viscoelastic Properties of Polymers, John Wiley & Sons, New York, 1980.
Fillers, R.W. and Tschoegl, N.W., ‘The effect of pressure on the mechanical properties of polymers’, Trans. Soc. Rheol. 21, 1977, 51–100.
G’Sell, C., Strength of Metals and Alloys, Vol. 3, ICSMA 7, H.J. McQueen et al. (eds), 1985, 1943–1982.
G’Sell, C. and Gopez, A.J., ‘Plastic banding in glassy polycarbonate under plane simple shear’, J. Mater. Sci. 20, 1985, 3462–3478.
Haward, R.N., ‘The post-yield behavior of amorphous polymers’, in The Phvsics of Glassy Polymers, R.N. Haward (ed.), Applied Science Publishers, London, 1973, 340–393.
James, H.M. and Guth, E., ‘Theory of the elastic properties of rubber’, J. Chem. Phys. 11, 1943, 455–481.
Knauss, W.G. and Emri, I., ‘Non-linear viscoelasticity based on free volume consideration’, Comput. & Structures 13, 1981, 123–128.
Knauss, W.G. and Emri, I., ‘Volume change and the nonlinearly thermo-viscoelastic constitution of polymers’, Polym. Engrg. Sci. 27, 1987, 86–100.
Knauss, W.G. and Kenner, V.H., ‘On the hygrothermomechanical characterization of Polyvinyl Acetate’, J. Appl. Phys. 51, 1980, 5131–5136.
Liang, Y.-M., ‘Toughening mechanisms in mixed-mode interfacial fracture’, Ph.D. Dissertation, The University of Texas at Austin, 1993.
Liang, Y.-M. and Liechti, K.M., ‘On the large deformation and localization behavior of an epoxy resin under multiaxial stress states’, Internat. J. Solids Struct. 33, 1996, 1479–1500.
Liechti, K.M., Liang, Y.-M., Arzoumanidis, A.G., Popelar, C.F. and Shah, J.H., ‘Deformation and fracture mechanisms in automotive adhesively bonded joints’, Final Report, EMRL 96-6, University of Texas at Austin, 1996.
Lu, H. and Knauss, W.G., ‘The role of dilatation in the nonlinearly viscoelastic behavior of PMMA under multiaxial stress states’, Mech. Time Dependent Mater. 2, 1999, 307–334.
Lustig, S.R., Shay, Jr., R.M. and Caruthers, J.M., ‘Thermodynamic constitutive equations for materials with memory on a material time scale’, J. Rheol. 40, 1996, 69–106.
O’Dowd, N.P. and Knauss, W.G., ‘Time dependent large principal deformation of polymers’, J. Mech. Phys. Solids 43, 1995, 771–792.
Popelar, C.F., ‘Nonlinear multiaxial viscoelastic characterization and modeling of structural adhesives’, Ph.D. Dissertation, The University of Texas at Austin, 1997.
Popelar, C.F. and Liechti, K.M., ‘Multiaxial nonlinear viscoelastic characterization and modeling of a structural adhesive’, J. Engrg. Mater. Technol. 119, 1997, 205–210.
Schapery, R.A., ‘An engineering theory of nonlinear viscoelasticity with applications’, Internat. J. Solids Struct. 2, 1966, 407–425.
Schapery, R.A., ‘On the characterization of nonlinear viscoelastic materials’, Polym. Engrg. Sci. 9, 1969, 295–310.
Shay, Jr., R.M. and Caruthers, J.M., ‘A new nonlinear viscoelastic constitutive equation for predicting yield in amorphous solid polymers’, J. Rheol. 30, 1986, 781–827.
Wang, M.C. and Guth, E.J., ‘Statistical theory of networks of non-Gaussian flexible chains’, J. Chem. Phys. 20, 1952, 1144–1157.
Whitney, W. and Andrews, R.D., ‘Yielding of glassy polymers: Volume effects’, J. Polym. Sci.: Part C 16, 1967, 2981–2990.
Wu, P.D. and van der Giessen, E., ‘Analysis of shear band propagation in amorphous glassy polymers’, Internat. J. Solids Struct. 31, 1994, 1493–1517.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Popelar, C., Liechti, K. A Distortion-Modified Free Volume Theory for Nonlinear Viscoelastic Behavior. Mech Time-Depend Mater 7, 89–141 (2003). https://doi.org/10.1023/A:1025625430093
Issue Date:
DOI: https://doi.org/10.1023/A:1025625430093