Abstract
Colmonoy 6 (NiCrSiB) is a Ni-based alloy recognized for its superior mechanical properties, attributed to the presence of a dispersion of hard carbides and borides, which is strongly dependent on processing technique. This work gathered microstructure data from the literature and analyzed Colmonoy 6 coatings deposited by plasma transferred arc hardfacing. The aim of the study was to determine the influence of PTA deposition parameters and substrate chemical composition on NiCrSiB coating characteristics. Coatings were characterized in terms of their hardness, dilution, and microstructure, as well as mass loss during abrasive sliding wear tests. The results showed that coating performance is strongly dependent on the chemical composition of the substrate. Carbon steel substrate yielded coatings with greater wear resistance. Processing parameters also alter the performance of coatings, and the lower current and lower travel speed result in reduced mass loss.
Similar content being viewed by others
References
P.Crook and H.N.Farmer, Friction and Wear of Hardfacing Alloys, Vol. 18, ASM Handbook, ASM International, Materials Park, OH, 1992, p 758–765
R. Kaul, P. Ganesh, S.K. Albert, A. Jaiswal, N.P. Lalla, A. Gupta, C.P. Paul, and A.K. Nath, Laser Cladding of Austenitic Stainless steel with Nickel Base Hardfacing Alloy, Surf. Eng., 2003, 19, p 269–273
Technical Data Sheet, No. Ni.-1.1B, Wall Colmonoy Corporation, Madison Heights, MI, USA 1990
C.P. Paul, A. Jain, P. Ganesh, J. Negi, and A.K. Nath, Laser Rapid Manufacturing of Colmonoy Components, Opt. Lasers Eng., 2006, 44, p 1096–1109
C. Sudha, P. Shankar, R.V. Subba Rao, R. Thirumurugesan, M. Vijayalakshmi, and Baldev. Raj, Microchemical and Microstructural Studies in a PTA Weld Overlay of NiCrSiB Alloy on AISI, 304L Stainless Steel, Surf. Coat. Technol., 2008, 202, p 2103–2112
A. Conde, F. Zubiri, and J. de Damborenea, Cladding of Ni-Cr-B-Si 238 Coatings a High Power Diode Laser, Mater. Sci. Eng., 2002, A334, p 233–238
C. Navas, R. Colaço, J. de Damborenea, and R. Vilar, Abrasive Wear Behaviour of Laser Clad and Flame Sprayed-Melted NiCrBSi Coatings, Surf. Coat. Technol., 2006, 200, p 6854–6862
Q. Ming, L.C. Lim, and Z.D. Chen, Laser Cladding of Nickel-Based Hardfacing Alloys, Surf. Coat. Technol., 1998, 106, p 174–182
C.R. Das, S.K. Albert, A.K. Bhaduri, C. Sudha, and A.L.E. Terrance, Characterisation of Nickel Based Hardfacing Deposits on Austenitic Stainless Steel, Surf. Eng., 2005, 21, p 290–296
A.E. Yaedu and A.S.C.M. D’Oliveira, Co based Alloy PTA Hardfacing with Different Dilution Levels, Mater. Sci. Technol., 2005, 21, p 459–466
Matweb, http://www.matweb.com. Accessed 03/04/20010.
W. Wu and L. Wu, The Wear Behavior Between Hardfacing Materials, Met. Mater. Trans. A, 1996, 27A, p 3639–3648
STELLITE, http:www.stellite.com. Accessed on 03/03/2010.
J.R. Davis, Surface Engineering for Corrosion and Wear Resistance, ASM International, Materials Park, OH, 2001
V.A.B. Almeida, E.H. Takano, I. Mazzaro, and A.S.C.M. D’Oliveira, Evaluation of Ni-Al Coatings Processed by Plasma Transferred Arc, Surf. Eng., 2011, 27, p 266–271
C.S. Ramachandran, V. Balasubramanian, R. Varahamoorthy, and S. Babu, Dry Sliding Wear Behaviour of Plasma Transferred Arc Hardfaced Colmonoy Surface, Surf. Eng., 2009, 25(6), p 440–448
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Reinaldo, P.R., D’Oliveira, A.S.C.M. NiCrSiB Coatings Deposited by Plasma Transferred Arc on Different Steel Substrates. J. of Materi Eng and Perform 22, 590–597 (2013). https://doi.org/10.1007/s11665-012-0271-7
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11665-012-0271-7