Abstract
The main goal of this investigation is to determine the influence of grain size on the mechanical properties and, specifically, the intrinsic ductility of nanocrystalline (nc) Fe. Ball-milled nc Fe was consolidated into compacts of near theoretical density by uniaxial warm pressing. Compaction parameters and annealing treatments resulted in a range of grain sizes for subsequent mechanical testing. The miniaturized disk bend test, hardness, and the automated ball indentation (ABI) method were used to test nanocrystal (nc) iron in compression and tension. The deformation and fracture morphologies of the tested samples were characterized by light and scanning electron microscopy. The hardness, as a function of the grain size, was described with a Hall-Petch slope, which was smaller than that in coarse-grained Fe. In tension, the material failed in a macroscopically brittle manner, while local ductility in very concentrated shear bands was observed. The compressive characteristics of the nc Fe were similar to those of a perfectly plastic material. The results are discussed in the context of the mechanical behavior of coarse-grained polycrystalline metals and alloys.
Similar content being viewed by others
References
L.S. Darken: Trans. Am. Soc. Met., 1961, vol. 54, p. 600.
J.S. Koehler: Phys. Rev. B, 1970, vol. 2, pp. 547–51.
R.W. Armstrong: in Yield, Flow and Fracture of Polycrystals, T.N. Baker, ed., Applied Science Publishers, Essex, England, 1983, pp. 1–31.
R.W. Siegel and G.E. Fougere: Nanostruct. Mater., 1995, vol. 6, pp. 205–16.
H. Hahn and K.A. Padmanabhan: Nanostruct. Mater., 1995, vol. 6, pp. 191–200.
M.J. Mayo: in Mechanical Properties and Deformation Behavior of Materials Having Ultra-Fine Microstructures, M. Nastasi, ed., Kluwer Academic Publishers, Dordrecht, The Netherlands, 1993, pp. 361–80.
E.O. Hall: Proc. Phys. Soc., 1951, vol. 9, pp. 742–53.
N.J. Petch: J. Iron Steel Inst., 1953, vol. 173, pp. 25–28.
N.J. Petch: Phil. Mag., 1956, vol. 1, pp. 186–90.
R. Armstrong, I. Codd, R.M. Douthwaite, and N.J. Petch: Phil. Mag., 1962, vol. 7, pp. 45–58.
G.E. Fougere, J.R. Weertman, and R.W. Siegel: Nanostruct. Mater., 1993, vol. 3, pp. 379–84.
U. Erb, G. Palumbo, R. Zugic, and K.T. Aust: in Processing and Properties of Nanocrystalline Materials, C. Suryanarayana, J. Singh, and F.H. Froes, eds., TMS, Warrendale, PA, 1996, pp. 93–110.
U. Köster, J. Meinhardt, and H. Alves: Mater. Sci. Forum, 1995, vols. 179–181, pp. 533–38.
T.R. Malow, C.C. Koch, P.Q. Miraglia, and K.L. Murty: Mater. Sci. Eng. A, 1998, in press.
T.R. Malow and C.C. Koch: North Carolina State University, Raleigh, NC, unpublished research, 1998.
T.R. Malow and C.C. Koch: Acta Mater., 1997, vol. 45, pp. 2177–86.
H.P. Klug and L. Alexander: X-ray Diffraction Procedures for Polycrystalline and Amorphous Materials, 2nd ed., John Wiley & Sons, New York, NY, 1974, p. 618.
A. Guinier: X-Ray Diffraction, W.H. Freeman and Co., San Francisco, CA, 1963, p. 121.
G.K. Williamson and W.H. Hall: Acta Metall., 1953, vol. 1, pp. 22–31.
M.A. Myers and K.K. Chawla: Mechanical Metallurgy, Prentice-Hall, Englewood Cliffs, NJ, 1984, p. 52.
J.C. Holzer, R. Birringer, J. Eckert, C.E. Krill Ill, and W.L. Johnson: Mater. Res. Soc. Symp. Proc., 1992, vol. 272, pp. 282–88.
J. Weissmüller, J. Löffler, and M. Kleber: Nanostruct. Mater., 1995, vol. 6, pp. 105–14.
X.Y. Qin, X.J. Wu, and L.D. Zhang: Nanostruct. Mater., 1995, vol. 5, pp. 101–10.
J.S.C. Jang and C.C. Koch: Scripta Metall. Mater., 1990, vol. 24, p. 1599.
D. Tabor: The Hardness of Metals, Clarendon Press, Oxford, United Kingdom, 1951, p. 95 ff.
G.E. Dieter: Mechanical Metallurgy, 2nd ed., McGraw-Hill, New York, NY, 1976, p. 329 ff.
D.K. Shetty, I.G. Wright, N. Mincer, and A.H. Clauer: J. Mater. Sci., 1985, vol. 20, pp. 1873–82.
Metals Handbook, vol. 12, Fractography, 9th ed., ASM, Metals Park, OH, 1987, p. 12 ff.
A. Nadai: Theory of Flow and Fracture of Solids, 2nd ed., McGraw-Hill, New York, NY, 1950, p. 527 ff.
T. Haubold, R. Bohn, R. Birringer, and H. Gleiter: Mater. Sci. Eng., 1992, vol. A153, pp. 679–83.
H. Hahn and H. Gleiter: Scripta Metall., 1979, vol. 13, pp. 3–6.
D.A. Molodov, J. Swiderski, G. Gottstein, W. Lojkowski, and L.S. Shvindlerman: Acta Metall. Mater., 1994, vol. 42, pp. 3397–3407.
P.G. Shewmon: Diffusion in Solids, 2nd ed., TMS, Warrendale, PA, 1989, p. 84 ff.
A. Cracknell and A.J. Petch: Acta Metall., 1955, vol. 3, pp. 186–89.
H. Conrad and G. Schoek: Acta Metall., 1960, vol. 8, pp. 791–96.
M.M. Hutchinson: Phil. Mag., 1963, vol. 8, pp. 121–27.
J.G.Y. Chow, S.B. McRickard, and D.H. Gurinsky: Special Technical Publication No. 341, ASTM, Philadelphia, PA, 1963, pp. 46–66.
W. Morrison: Trans. Am. Soc. Met., 1966, vol. 59, pp. 824–46
E. Anderson, D.L.W. King, and J. Spreadborough: Trans. AIME, 1968, vol. 242, pp. 115–19.
R.A. Jago and N. Hansen: Acta Metall., 1986, vol. 34, pp. 1711–20.
N. Hansen: Acta Metall., 1977, vol. 25, pp. 863–69.
R.Z. Valiev, N.A. Krasilnikov, and N.K. Tsenev: Mater. Sci. Eng., 1991, vol. A137, p. 35.
P.G. Sanders, C.J. Youngdahl, and J.R. Weertman: Mater. Sci. Eng., 1997, vols. A234-A236, pp. 77–82.
R.Z. Valiev, F. Chmelik, F. Bordeaux, G. Kapelski, and B. Baudelet: Scripta Metall. Mater., 1992, vol. 27, pp. 855–60.
A.W. Thompson: in Work Hardening in Tension and Fatigue, A.W. Thompson, ed., American Institute of Mining, Metallurgical and Petroleum Engineers, New York, NY, 1977, pp. 89–126.
R.W. Armstrong: in Strength of Metals and Alloys, P. Haasen, V. Gerold, and G. Kostorz, eds., Pergamon Press, Elmstord, NY, 1979, pp. 795–800.
C.A. Pampillo: J. Mater. Sci., 1975, vol. 10, pp. 1194–1227.
B.R. Lawn: Fracture of Brittle Solids, 2nd ed., Cambridge University Press, Cambridge, United Kingdom, 1993, p. 249 ff.
B. Günther, A. Baalmann, and H. Weiss: Mater. Res. Soc. Symp. Proc., 1990, vol. 195, pp. 611–15.
R. Suryanarayanan, C.A. Frey, S.M.L. Sastry, B.E. Waller, and W.E. Buhro: in Processing and Properties of Nanocrystalline Materials, C. Suryanarayana, J. Singh, and F.H. Froes, eds., TMS, Warrendale, PA, 1996, pp. 407–13.
J.E. Carsley, W.W. Milligan, S.A. Hackney, and E.C. Aifantis: Metall. Mater. Trans. A, 1995, vol. 26A, pp. 2479–81.
J.E. Carsley, W.W. Milligan, S.A. Hackney, and E.C. Hackney: in Processing and Properties of Nanocrystalline Materials, C. Suryanarayana, J. Singh, and F.H. Froes, eds., TMS, Warrendale, PA, 1996, pp. 415–20.
J.E. Carsley, G.R. Shaik, W.W. Milligan, and E.C. Aifantis: in Chemistry and Physics of Nanostructures and Related Non-Equilibrium Materials, E. Ma, B. Fultz, J. Morral, and P. Nash, eds., TMS, Warrendale, PA, 1997, pp. 183–92.
G.R. Shaik and W.W. Milligan: Metall. Mater. Trans. A, 1997, vol. 28A, pp. 895–904.
X.H. Zhu, J.E. Carsley, W.W. Milligan, and E.C. Aifantis: Scripta Mater., 1997, vol. 36, pp. 721–26.
J.P. Hirth: “Viewpoint Set on Shear Bands” in Scripta Met., J.P. Hirth, ed., 1984, vol. 18, pp. 421–58.
H. Dève, S. Harren, C. McCullough, and R.J. Asaro: Acta Metall., 1988, vol. 36, pp. 341–65.
H.E. Dève and R.J. Asaro: Metall. Trans. A, 1989, vol. 20A, pp. 579–93.
Author information
Authors and Affiliations
Additional information
This article is based on a presentation made in the symposium “Mechanical Behavior of Bulk Nanocrystalline Solids,” presented at the 1997 Fall TMS Meeting and Materials Week, September 14–18, 1997, in Indianapolis, Indiana, under the auspices of the Mechanical Metallurgy (SMD), Powder Materials (MDMD), and Chemistry and Physics of Materials (EMPMD/SMD) Committees.
Rights and permissions
About this article
Cite this article
Malow, T.R., Koch, C.C. Mechanical properties, ductility, and grain size of nanocrystalline iron produced by mechanical attrition. Metall Mater Trans A 29, 2285–2295 (1998). https://doi.org/10.1007/s11661-998-0106-1
Issue Date:
DOI: https://doi.org/10.1007/s11661-998-0106-1