Abstract
The aim of this study is to predict the kinetics of deformation-induced martensite transformation (DIMT) by proposing a novel model considering the effects of three loading characteristics: temperature, strain rate, and stress state. Experiments including hot compression, tension, notched tension, and shear tests using 304 stainless steel plate were carried out to investigate the transformation kinetics. After a decoupling analysis was conducted on the effects of the three characteristics, particularly the temperature and strain rate effects under high strain rate loading conditions, three kinetic sub-models were established individually for each effect, and the proposed model was developed by multiplying the three kinetic sub-models. A stepwise fitting method was proposed for the calibration of material constants to replace complex iterative optimization algorithms and improve the certainty of the values of the material constants. The proposed model was further validated using the experimental data of various austenitic stainless steels obtained from previous studies. Result shows the model revealed satisfactory accuracy in predicting the DIMT behavior in material experiment. After compiling the model into a USDFLD subroutine, simulation of a heat-assisted fine-blanking process was conducted in ABAQUS, giving a reasonable prediction of martensite content of the blanking parts.
Similar content being viewed by others
References
W.S. Park, S.W. Yoo, M.H. Kim, and J.M. Lee: Mater. Des., 2010, vol. 31, pp. 3630–40.
B. Jia, A. Rusinek, R. Pesci, S. Bahi, and R. Bernier: Int. J. Mech. Sci., 2020, vol. 170, p. 105356.
X. Chen, L. Ma, C. Zhou, Y. Hong, H. Tao, J. Zheng, and L. Zhang: Corros. Sci., 2019, vol. 148, pp. 159–70.
N. Ethiraj and V. Senthil Kumar: Adv. Mater. Res., 2011, vol. 418–420, pp. 1410–17.
Q. Zheng, X. Zhuang, J. Hu, and Z. Zhao: Mater. Charact., 2020, vol. 166, p. 110452.
M.J. Sohrabi, M. Naghizadeh, and H. Mirzadeh: Arch. Civ. Mech. Eng., 2020, vol. 20, pp. 1–24.
M. Naghizadeh and H. Mirzadeh: Vacuum, 2018, vol. 157, pp. 243–48.
G. Sun, L. Du, J. Hu, B. Zhang, and R.D.K. Misra: Mater. Sci. Eng. A, 2019, vol. 746, pp. 341–55.
J.V. Tilak Kumar, J. Sudha, K.A. Padmanabhan, A.V. Frolova, and V.V. Stolyarov: Mater. Sci. Eng. A, 2020, vol. 777, p. 139046.
S.S. Hecker, M.G. Stout, K.P. Staudhammer, and J.L. Smith: Metall. Trans. A, 1982, vol. 13, pp. 619–26.
L.E. Murr, K.P. Staudhammer, and S.S. Hecker: Metall. Trans. A, 1982, vol. 13, pp. 627–35.
A. Das and S. Tarafder: Int. J. Plast., 2009, vol. 25, pp. 2222–47.
P. Hedström, L.E. Lindgren, J. Almer, U. Lienert, J. Bernier, M. Terner, and M. Odén: Metall. Mater. Trans. A, 2009, vol. 40, pp. 1039–48.
G.N. Haidemenopoulos, N. Aravas, and I. Bellas: Mater. Sci. Eng. A, 2014, vol. 615, pp. 416–23.
G.W. Powell: Trans. Am. Soc. Met., 1958, vol. 50, pp. 478–97.
A.A. Lebedev and V.V. Kosarchuk: Int. J. Plast., 2000, vol. 16, pp. 749–67.
H. Mirzadeh and A. Najafizadeh: J. Alloys Compd., 2009, vol. 476, pp. 352–55.
H. Mirzadeh and A. Najafizadeh: Mater. Charact, 2008, vol. 59, pp. 1650–54.
A. Das, S. Tarafder, and P.C. Chakraborti: Mater. Sci. Eng. A, 2011, vol. 529, pp. 9–20.
W. Mu, M. Rahaman, F.L. Rios, J. Odqvist, and P. Hedström: Mater. Des., 2021, vol. 197, p. 109199.
M.C. Mataya and V.E. Sackschewsky: Metall. Mater. Trans. A, 1994, vol. 25, pp. 2737–52.
S.S.M. Tavares, J.M. Pardal, M.J.G. da Silva, H.F.G. Abreu, and M.R. da Silva: Mater. Charact., 2009, vol. 60, pp. 907–11.
H.C. Shin, T.K. Ha, and Y.W. Chang: Scr. Mater., 2001, vol. 45, pp. 823–29.
P.M. Ahmedabadi, V. Kain, and A. Agrawal: Mater. Des., 2016, vol. 109, pp. 466–75.
T. Angel: J. Iron Steel Inst., 1954, vol. 177, pp. 165–74.
R.G. Stringfellow, D.M. Parks, and G.B. Olson: Acta Metall. Mater., 1992, vol. 40, pp. 1703–16.
Y. Tomita and T. Iwamoto: Int. J. Mech. Sci., 1995, vol. 37, pp. 1295–1305.
W.J. Dan, W.G. Zhang, S.H. Li, and Z.Q. Lin: Comput. Mater. Sci., 2007, vol. 40, pp. 101–07.
S.H. Li, W.J. Dan, W.G. Zhang, and Z.Q. Lin: Comput. Mater. Sci., 2007, vol. 40, pp. 292–99.
Q. Zheng, X. Zhuang, and Z. Zhao: Metall. Mater. Trans. A, 2021, vol. 52, pp. 5200–14.
G.B. Olson and M. Cohen: Metall. Trans. A, 1975, vol. 6A, pp. 791–95.
A.M. Beese and D. Mohr: Acta Mater., 2011, vol. 59, pp. 2589–2600.
V.V. Kosarchuk, L.V. Zaitseva, A.A. Lebedev, and B.I. Koval’chuk: Strength Mater., 1989, vol. 21, pp. 60–64.
J. Talonen and H. Hänninen: Acta Mater., 2007, vol. 55, pp. 6108–18.
N. Tsuchida, Y. Yamaguchi, Y. Morimoto, T. Tonan, Y. Takagi, and R. Ueji: ISIJ Int., 2013, vol. 53, pp. 1881–87.
Z. Zhu, W.T. Fu, R.B. Li, Q.W. Chen, Z.A. Zhou, Z.H. Wang, J.Q. Liu, and S.H. Sun: J. Iron Steel Res. Int., 2021, vol. 28, pp. 1030–36.
B. He: Materials (Basel), 2020, vol. 13, pp. 1–31.
Acknowledgments
This research was supported by the Shanghai Outstanding Academic Leaders Plan (21XD1422000).
Conflict of Interest
The authors declare that they have no conflict of interest.
Author information
Authors and Affiliations
Corresponding authors
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
Springer Nature or its licensor (e.g. a society or other partner) holds exclusive rights to this article under a publishing agreement with the author(s) or other rightsholder(s); author self-archiving of the accepted manuscript version of this article is solely governed by the terms of such publishing agreement and applicable law.
About this article
Cite this article
Zhang, W., Zheng, Q., Gu, N. et al. Phenomenological Modeling of Deformation-Induced Martensite Transformation Kinetics in Austenitic Stainless Steels. Metall Mater Trans A 55, 73–92 (2024). https://doi.org/10.1007/s11661-023-07228-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11661-023-07228-0