Skip to main content
SpringerLink
Log in

Spark radius modeling of resistance-capacitance pulse discharge in micro-electric discharge machining of Ti-6Al-4V: an experimental study

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

Several modeling and simulations have been reported to characterize the electric discharge machining (EDM) and micro-electric discharge machining (micro-EDM) processes. However, these models have been considered spark radius as a function of time or time and current as well as these models are valid only for transistor-type pulse discharge circuits. Therefore, it is important to develop an accurate model to predict the spark radius for RC-relaxation circuits where capacitance and voltage are the important process parameters. In this paper, an attempt has been made to develop a mathematical model predicting the single-spark radius produced during micro-EDM of Ti-6Al-4V. A series of experiments were conducted based on three-level full factorial experimental design with four center point runs. Capacitance and voltage were taken as the variable factors and spark radius was measured as the response. Based on the experimental results, the effect of capacitance and voltage on spark radius was studied in detail with analysis of variance. The results showed that capacitance significantly influenced the spark radius compared to voltage. In addition, a mathematical model has been developed to correlate the capacitance and voltage with spark radius by adopting regression analysis. Finally, the developed model equation was validated with confirmatory experiments and the predicted and experimental spark radius was found to be in good agreement with a prediction error less than 5 %.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Jahan MP, Rahman M, Wong YS (2011) A review on the conventional and micro electric discharge machining of tungsten carbide. Int J Mach Tools Manuf 51:837–858

    Article  Google Scholar 

  2. Kuriachen B, Somashekhar KP, Mathew J (2014) Multiresponse optimization of micro-wire electrical discharge machining process. Int J Adv Manuf Technol. doi:10.1007/s00170-014-6005-2

    Google Scholar 

  3. Jilani ST, Pandey PC (1982) Analysis and modeling of EDM parameters. Precis Eng 4:215–221

    Article  Google Scholar 

  4. Dibitonto DD, Eubank PT, Patel MR, Barrufet MA (1989) Theoretical model of the electric discharge machining process. I. The cathode erosion model. J Appl Phys 66:4095–4103

    Article  Google Scholar 

  5. Patel MR, Barrufet MA, Eubank PT, Dibitonto DD (1989) Theoretical model of the electric discharge machining process. II. The anode erosion model. J Appl Phys 66:4104–4111

    Article  Google Scholar 

  6. Shankar P, Jain VK, Sundararajan T (1997) Analysis of spark profiles during EDM process. Mach Sci Technol 1:195–217

    Article  Google Scholar 

  7. Ajit S, Amitabha G (1999) A thermo electric model of material removing during electric discharge machining. Int J Mach Tools Manuf 39:669–682

    Article  Google Scholar 

  8. Yu ZY, Kozak J, Rajurkar KP (2003) Modeling and simulation of micro EDM process. CIRP Ann 52:143–146

    Article  Google Scholar 

  9. Dhanik S, Joshi SS (2005) Modeling of a single resistance capacitance pulse discharge in micro electro discharge machining. J Manuf Sci Eng 127:759–767

    Article  Google Scholar 

  10. Marafona J, Chousal JAG (2006) A finite element model of EDM based on the joule effect. Int J Mach Tools Manuf 46:595–602

    Article  Google Scholar 

  11. Joshi SN, Pande SS (2009) Development of an intelligent process model for EDM. Int J Adv Manuf Technol 45:300–317

    Article  Google Scholar 

  12. Izquierdo B, Sanchez JA, Plaza S, Pombo I, Ortega N (2009) A numerical model of the EDM process considering the effect of multiple discharges. Int J Mach Tools Manuf 49:220–229

    Article  Google Scholar 

  13. Joshi SN, Pande SS (2010) Thermo physical modeling of die sinking EDM process. J Manuf Process 12:45–56

    Article  Google Scholar 

  14. Xie BC, Wang YK, Wang ZL, Zhao WS (2011) Numerical simulation of titanium alloy machining in electric discharge machining process. Trans Nonferrous Metals Soc China 21:434–439

    Article  Google Scholar 

  15. Shabgard M, Ahmadi R, Seyedzavvar M, Oliaei SNB (2013) Mathematical and numerical modeling of the effect of input-parameters on the flushing efficiency of plasma channel in EDM process. Int J Mach Tools Manuf 65:79–87

    Article  Google Scholar 

  16. Izquierdo B, Plaza S, Sanchez JA, Pombo I, Ortega N (2012) Numerical prediction of heat affected layer in the EDM of aeronautical alloys. Appl Surf Sci 259:780–790

    Article  Google Scholar 

  17. Zhang Y, Liu Y, Shen Y, Li Z, Ji R, Cai B (2014) A novel method of determining energy distribution and plasma diameter of EDM. Int J heat Mass Transf 75:425–432

    Article  Google Scholar 

  18. Yeo SH, Kurnia W, Tan PC (2008) Critical assessment and numerical comparison of electro thermal models in EDM. J Mater Process Technol 203:241–251

    Article  Google Scholar 

  19. Snoeys R, Van Dijick FS (1971) Investigation of electro discharge machining operations by means of thermo mathematical model. CIRP Ann 20:35–37

    Google Scholar 

  20. Van Dijick FS, Dutre WL (1974) Heat conduction model for the calculation of the volume of molten metal in electric discharges [discharge machining]. J Phys D (Appl Phys) 7:899–910

    Article  Google Scholar 

  21. Beck JV (1981) Transient temperatures in a semi-infinite cylinder heated by a disk heat source. Int J Heat Mass Transf 24:1631–1640

    Article  MATH  Google Scholar 

  22. Jilani ST, Pandey PC (1983) Analysis of surface erosion in electrical discharge machining. Wear 84:275–284

    Article  Google Scholar 

  23. Dhanik S, Joshi SS, Ramakrishnan N, Apte PR (2005) Evolution of EDM process modeling and development towards modeling of the micro EDM process. Int J Manuf Technol Manag 7:157–180

    Google Scholar 

  24. Yu ZY, Kozak J, Rajurkar KP (2003) Modeling and simulation of micro EDM process. CIRP Ann Manuf Technol 52:143–146

    Article  Google Scholar 

  25. Murali MS, Yeo SH (2005) Process simulation and residual stress estimation of micro electric discharge machining using finite element method. J Appl Phys 44(7A):5254–5263

    Article  Google Scholar 

  26. Yeo SH, Kurnia W, Tan PC (2007) Electro thermal modeling of anode and cathode in micro EDM. J Phys D 40(8):2513

    Article  Google Scholar 

  27. Kiran KMP, Joshi SS (2007) Modeling of surface roughness and the role of debris in micro-EDM. J Manuf Sci Eng 129(2):265–273

    Article  Google Scholar 

  28. Allen P, Chen X (2007) Process simulation of micro electro discharge machining on molybdenum. J Mater Process Technol 186:346–355

    Article  Google Scholar 

  29. Mathew J, Allesu K, Srisailam S, Somashekar KP, Prakash Naidu P, Suvin PS (2012) Estimation of residual stress and crater shape in μ-EDM by finite element method. Proceedings of 7th ASME International conference, Texas, USA

  30. Somashekhar KP, Mathew J, Ramachandran N (2012) Electrothermal theory approach for numerical approximation of the μ-EDM process. Int J Adv Manuf Technol 61:1241–1246

    Article  Google Scholar 

  31. Somashekhar KP, Panda S, Mathew J, Ramachandran N (2013) Numerical simulation of micro-EDM model with multi-spark. Int J Adv Manuf Technol. doi:10.1007/s00170-013-5319-9

    Google Scholar 

  32. Tan PC, Yeo SH (2008) Modeling of overlapping craters on micro-electrical discharge machining. J Phys D 41(20):205302

    Article  Google Scholar 

  33. Karthikeyan G, Garga AK, Ramkumar J, Dhamodaran S (2012) A microscopic investigation of machining behavior in ED-milling process. J Manuf Process 14:297–306

    Article  Google Scholar 

  34. Yoo BH, Min BK, Lee SJ (2010) Analysis of the machining characteristics of EDM as functions of the mobilities of electrons and ions. Int J Precis Eng Manuf 11(4):629–632

    Article  Google Scholar 

  35. Jahan MP, Wong YS, Rahman M (2010) A study on the quality micro-hole machining of tungsten carbide by micro-EDM process using transistor and RC-type pulse generator. J Mater Process Technol 209:1706–1716

    Article  Google Scholar 

  36. Luo UF (1995) The dependence of interspace discharge transitivity upon the gap debris in precision electrodischarge machining. J Mater Process Technol 68(2):121–131

    Article  Google Scholar 

  37. Chen Y, Mahdivian SM (2000) Analysis of electro-discharge machining process and its comparison with experiments. J Mater Process Technol 104(1–2):150–157

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. School of Mechanical and Building Sciences, VIT University, Vellore, India

    B. Kuriachen

  2. Department of Mechanical Engineering, National Institute of Technology Calicut, Kerala, India

    Jose Mathew

Authors
  1. B. Kuriachen
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Jose Mathew
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to B. Kuriachen.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Kuriachen, B., Mathew, J. Spark radius modeling of resistance-capacitance pulse discharge in micro-electric discharge machining of Ti-6Al-4V: an experimental study. Int J Adv Manuf Technol 85, 1983–1993 (2016). https://doi.org/10.1007/s00170-015-7999-9

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-015-7999-9

Keywords

Search

Navigation