Skip to main content
SpringerLink
Log in

Fracture and mechanical properties of friction stir spot welds in 6063-T6 aluminum alloy

  • Original Article
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

The influence of the tool dimensions and of the welding parameters on the fracture and lap shear properties of friction stir spot welds is investigated. Interrupted lap shear tests allow to follow the mechanisms leading to weld fracture. A triangular cavity opens at the hook during lap shear testing. The distance between this triangular cavity and the hole left by the pin is the main parameter controlling the type of fracture. A too short distance favors a fracture through the weld nugget and hence should be avoided. In particular, this happens when the tool pin diameter is too small and when the plunge rate is too large. Fracture initiating at the triangular cavity and following the thermomechanically affected zone, i.e., by the pullout of the weld nugget, is preferred. This fracture type leads to significant plastic deformation and generally favors a large ultimate force during lap shear testing. Large ultimate forces are observed when the welds are cooler (large plunge rates and low rotation speeds), but the welding conditions should be chosen so as not to lead to fracture trough the weld nugget.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Thomas WM, Nicholas ED, Needham JC, Murch MG, Templesmith P, Dawes CJ (1991) Friction stir butt welding. GB Patent application n. 9125978-8

  2. Threadgill PL, Leonard AJ, Shercliff HR, Withers PJ (2009) Friction stir welding of aluminium alloys. Int Mater Rev 54(2):49–93

    Article  Google Scholar 

  3. Mishra RS, Ma ZY (2005) Friction stir welding and processing. Mater Sci Eng 50:1–78

    Article  MATH  Google Scholar 

  4. Wang D-A, Lee S-C (2007) Microstructures and failure mechanisms of friction stir spot welds of aluminum 6061-T6 sheets. J Mater Process Technol 186(1–3):291–297

    Article  MathSciNet  Google Scholar 

  5. Gean A, Westgate SA, Kucza JC, Ehrstrom JC (1999) Static and fatigue behavior of spot-welded 5182-O aluminum alloy sheet. Weld J 78:80s–86s

    Google Scholar 

  6. Matsumoto K, Sasabe S (2001) Lap joints of aluminium alloys by friction stir welding. In: Proc. 3rd int. symp. FSW, Kobe, Japan

  7. Badarinarayan H, Shi Y, Li X, Okamoto K (2009) Effect of tool geometry on hook formation and static strength of friction stir spot welded aluminum 5754-O sheets. Int J Mach Tools Manuf 49(11):814–823

    Article  Google Scholar 

  8. Badarinarayan H, Yang Q, Zhu S (2009) Effect of tool geometry on static strength of friction stir spot-welded aluminum alloy. Int J Mach Tools Manu 49(2):142–148

    Article  Google Scholar 

  9. Merzoug M, Mazari M, Berrahal L, Imad A (2010) Parametric studies of the process of friction spot stir welding of aluminium 6060-T5 alloys. Mater Des 31(6):3023–3028

    Article  Google Scholar 

  10. Tozaki Y, Uematsu Y, Tokaji K (2007) Effect of processing parameters on static strength of dissimilar friction stir spot welds between different aluminium alloys. Fatigue Fract Eng M 30(2):143–148

    Article  Google Scholar 

  11. Yin YH, Sun N, North TH, Hu SS (2010) Hook formation and mechanical properties in AZ31 friction stir spot welds. J Mater Process Technol 210(14):2062–2070

    Article  Google Scholar 

  12. Bozzi S, Helbert-Etter AL, Baudin T, Klosek V, Kerbiguet JG, Criquid B (2010) Influence of FSSW parameters on fracture mechanisms of 5182 aluminium welds. J Mater Process Technol 210(11):1429–1435

    Article  Google Scholar 

  13. Yin YH, Sun N, North TH Hu SS (2010) Influence of tool design on mechanical properties of AZ31 friction stir spot welds. Sci Technol Weld Join 15(1):81–86

    Article  Google Scholar 

  14. Hirasawa S, Badarinarayan H, Okamoto K, Tomimura T, Kawanami T (2010) Analysis of effect of tool geometry on plastic flow during friction stir spot welding using particle method. J Mater Process Technol 210(11):1455–1463

    Article  Google Scholar 

  15. Tran V-X, Pan J, Pan T (2009) Effects of processing time on strengths and failure modes of dissimilar spot friction welds between aluminum 5754-O and 7075-T6 sheets. J Mater Process Technol 209(8):3724–3739

    Article  Google Scholar 

  16. Fujimoto M, Watanabe D, Abe N, Sato Y, Kokawa H (2010) Effects of process time and thread on tensile shear strength of al alloy lap joint produced by friction stir spot welding. Welding Int 24(3):169–175

    Article  Google Scholar 

  17. Arul S, Miller S, Kruger G, Pan T, Mallick P, Shih A (2008) Experimental study of joint performance in spot friction welding of 6111-T4 aluminium alloy. Sci Technol Weld Join 13(7):629–637

    Article  Google Scholar 

  18. Pan T, Joaquin A, Wilkosz DE, Feng Z, Santella ML (2004) Spot friction welding for sheet aluminum joining. In: Proc. 5th int. symp. FSW, Metz, France

  19. Wang DA, Chao C-W, Lin P-C, Uan J-Y (2010) Mechanical characterization of friction stir spot microwelds. J Mater Process Technol 210(14):1942–1948

    Article  Google Scholar 

  20. Lin P-C, Pan J, Pan T (2008) Failure modes and fatigue life estimations of spot friction welds in lap-shear specimens of aluminum 6111-T4 sheets. Part 2: welds made by a flat tool. Int J Fatigue 30(1):90–105

    Article  Google Scholar 

  21. Mitlin D, Radmilovic V, Pan T, Chen J, Feng Z, Santalla ML (2006) Structure properties relations in spot friction welded 6111 aluminium. Mater Sci Eng A441:79–96

    Article  Google Scholar 

  22. Su P, Gerlich A, North TH, Bendzsak GJ (2006) Material flow during friction stir spot welding. Sci Technol Weld Join 11(1):61–71

    Article  Google Scholar 

  23. Gerlich A, Su P, Yamamoto M, North TH (2008) Material flow and intermixing during dissimilar friction stir welding. Sci Technol Weld Join 13(3):254–264

    Article  Google Scholar 

  24. Simar A, Brechet Y, de Meester B, Denquin A, Pardoen T (2007) Sequential modeling of local precipitation, strength and strain hardening in friction stir welds of aluminium alloy 6005A-T6. Acta Mater 55:6133–6143

    Article  Google Scholar 

Download references

Author information

Authors and Affiliations

  1. Institute of Mechanics, Materials and Civil Engineering, Université catholique de Louvain, Place du Levant, 2 L5-04-01, 1348, Louvain-la-Neuve, Belgium

    Caroline Jonckheere, Bruno de Meester, Cédric Cassiers & Martin Delhaye

  2. Institute of Mechanics, Materials and Civil Engineering, Université catholique de Louvain, Place St Barbe 2 bte L5.02.02, 1348, Louvain-la-Neuve, Belgium

    Aude Simar

Authors
  1. Caroline Jonckheere
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Bruno de Meester
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Cédric Cassiers
    View author publications

    You can also search for this author in PubMed Google Scholar

  4. Martin Delhaye
    View author publications

    You can also search for this author in PubMed Google Scholar

  5. Aude Simar
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Aude Simar.

Rights and permissions

Reprints and permissions

About this article

Cite this article

Jonckheere, C., de Meester, B., Cassiers, C. et al. Fracture and mechanical properties of friction stir spot welds in 6063-T6 aluminum alloy. Int J Adv Manuf Technol 62, 569–575 (2012). https://doi.org/10.1007/s00170-011-3795-3

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-011-3795-3

Keywords

Search

Navigation