Sustainable Bio-Conversion of Rice Straw Waste into High Quality Organic Fertilizer ()
1. Introduction
Egypt generates up to 30 million ton/year of agricultural waste [1]. Almost half of it is directly burnt in the field [2]. Rice straw is one of the main types of agricultural waste generated in Egypt. In fact, it was estimated that around 5.9 million ton of rice straw used to be generated in 2013 [3]. Part of this rice straw is used at an individual level as a source of fuel for household cooking and heating, animal feed, fiber for pulping and plowing into farmland. Yet, the rest is dumped and burned in open fields causing serious environmental problems, including air pollution and soil degradation [3] [4]. Therefore, it became imperative to find efficient and cost-effective methods to reduce environmental pollution and recycle agricultural resources.
Rice straw contains cellulose, hemicellulose and lining, which makes it hard to decompose. However, several studies showed that rice straw could be used to produce high value-added products via composting process [5] [6].
Composting is an aerobic fermentation process that converts large amounts of agricultural waste into high quality soil amendment and/or organic fertilizer [3] [7] [8] [9], which can be used instead of the expensive and imported chemical fertilizers. The compost pile goes through four phases: 1) mesophilic phase is a preparatory stage, which initiates organic matter decomposition; 2) thermophilic phase in which microorganisms decompose organic matter at high temperatures ranging from 40˚C - 70˚C; 3) second mesophilic phase allowing re-establishment of the heat resistant microbes; and 4) maturity phase of constant nutrient contents [10] [11] [12] [13]. Although composting has been widely practiced, the process is still not fully understood due to high variety and heterogeneity of feedstocks [9]. The objective of composting is to accelerate and create optimum conditions for the naturally occurring decomposition process to take place.
Some studies showed that inoculating compost piles with different additives, including biochar, effective micro-organisms (EM), cellulose decomposing bacteria, starters containing bacillus, fungi, yeast, lactic acid bacteria, and animal manure, can improve the nutritional value of compost and/or organic fertilizer and accelerate the degradation process [14] [15]. Several producers of these additives claim that they can generate higher quality organic fertilizer during short period of time. Yet, the effect of these additives on the composting process is not fully studied and understood. The aim of this paper is to evaluate and compare the effect of inoculating different types of additives on composting of rice straw.
2. Materials and Methods
2.1. Raw Material
Rice straw is the main raw material used for composting in this experiment. Rice straw was sun dried and chopped. The properties of rice straw used are analysed for nutrients, heavy metals, physicochemical and are presented in Table 1.
2.2. Additives
Animal manure, commercial microbial inoculants imported from China, effective micro-organisms (EM), and biochar were inoculated to rice straw and the quality of the final compost was evaluated. Based on the literature, different inoculation rates were determined.
Regarding the animal manure many studies showed that co-composting with animal manure provide high nutrient content of the compost. Studied reported the addition of animal manure at rates varying from 30% [16] [17] to 60% [9].
Based on that, 40% of animal manure was added to rice straw in all treatments in this experiment.
In this study, a commercial microbial inoculants imported from China is used. It mainly contains lactic acid bacteria, yeasts, photosynthetic bacterial, etc. Their exact composition is not revealed and is seen as trade secret. No published studies have reported their exact composition nor their effect on composting process.
Another inoculant used in this experiment is EM, which consists of various strains of naturally occurring anaerobic nontoxic and non-pathogenic microorganisms in a carbohydrate-rich liquid carrier substrate (molasses nutrient solution). One part of commercial EM (EM-1) solution, produced by Egyptian Ministry of Agriculture, was added to one part of molasses and mixed with 20 parts of water to active EM solution and 100 mL of active solution was added to 50 kg of rice straw as recommended [17].
Recent studies have reported that biochar can be beneficial to the composting process. These studies reported application rates varying from 3% to 50%. According to Sanchez Monedero et al., the recommended application dose of biochar to compost is around 10% [18]. Some studies have also reported use of higher doses up to 50%; however, some authors have reported that doses higher than 20% can slow down the composting process [19]. Therefore, doses of 10% and 20% are used in this study.
2.3. Composting Procedure
The composting process took place at the American University in Cairo during the months of May, June and July. Rice straw is added to nine large fabric bags; each pile is mixed with natural rocks and inoculated with different additives as summarized in Table 2 and Table 3. Each pile is manually turned and water is added every week. The chemical, physical and biological parameters of all samples have been analyzed as per standards and specifications [20] - [25].
2.4. Statistical Analysis
All results are presented as the average of three replicates, and the means among different treatments are compared using one-way ANOVA using SPPS version 23. The null hypothesis states that the population means are all equal. A significance level α = 0.05 is used. The ANOVA analysis is performed on the data
![]()
Table 2. Piles content used for composting process.
![]()
Table 3. Types of rocks used and their corresponding quantities.
collected after 60days to calculate the p-value and understand whether different treatments have a significant effect on the properties of the final product or not.
3. Results and Discussion
3.1. Temperature Changes
The temperature changes for the nine compost piles and corresponding ambient temperatures are measured three times a week at different location in the pile using a digital thermometer. The results are presented in Figure 1. This experiment is conducted during the summer season and the ambient temperature variations throughout the composting period were between 29˚C and 40˚C.
An increase in piles temperatures was observed right after composting started. It is important to mention that this experiment was conducted in the summer season. Ambient temperature and treatments temperature were measured three times a week at different locations in the pile using a digital thermometer. The treatments are left three months for composting.
The temperatures increased rapidly to reach their maximum temperatures after 2 days in all treatments, which marks the end of the initial mesophilic phase and beginning of thermophilic phase. The increase in temperature during composting is due to the activity of microorganisms to degrade agricultural wastes [26] [27]. The highest temperature is observed in T3, T5 and T6 compared to other treatments, which indicates that these treatment has greater microbial activity.
After that, the temperatures started to decrease gradually, indicating a reduction in microbial activity. The observed fluctuations in temperature are due to the turning of pile. Then the temperature gradually decreased to reach mesophilic phase. After that, it stabilized near the ambient temperature after around 42 days.
3.2. Organic Carbon (OC, %) and Organic Matter (OM, %)
Three homogenized and randomized samples are taken manually after 10 days, 30 days and 60 days from top, middle and bottom of compost piles. The %OM were measured for the nine piles, three measurements were taken for each pile, then the OM by weight is calculated from the total solid content (TS) and the results are presented in Table 4. It is also worth mentioning that the volume of the piles decreased by around 40% by the end of the composting process. One-way ANOVA was performed on the data after 60 days and results indicate that p-value of 0.00 less than 0.05 confidence interval, which means that there is a significant difference between the means of different treatments.
Then %OC were calculated from %OM and average values are presented in Table 5.
The OM and OC decreases in all piles indicating that the organic substances are degraded and decomposed by micro-organisms [28]. The highest percentage losses are observed in T6 followed by T5. This reveals that these treatments have
![]()
Figure 1. Changes in temperatures in compost piles with relation to ambient temperatures for (a) T1, T2 and T3, (b) T4, T5 and T6, (c) T7, T8 and T9.
aTS refers to total solid content; bOM refers to Organic Matter; cThe % losses are the difference in OM in all piles after 30 and 60 days.
high content of easily decomposable substances compared to other treatments. This results are in line with the results obtained from the temperature profile.
3.3. Total Nitrogen, Ammonium and Nitrate Nitrogen
The total nitrogen (TN), ammonium nitrogen (NH+ 4) and nitrate nitrogen (NO− 3) were measured for all piles. Three measurements were taken for each pile. The average TN (%) values are presented in Table 6.
One-way ANOVA was performed on the data of TN after 60 days and results indicate that p-value of 0.00 less than 0.05 confidence interval, which means that there is a significant difference between the means of different treatments.
The results indicated that TN increased in some samples, while it decreased in others. In fact, TN slightly increased in treatments T1, T2 and T6 and decreased in all other treatments. Samples inoculated with biochar only (T5 and T7) showed relatively large TN loss, this could be attributed to relatively low N with high biodegradable material. These differences in TN could be due to difference in initial C/N ratios coupled with differences in the initial amount of TN and pH values [29].
Ammonium and nitrate nitrogen are of greater interest, as they have been used as maturity index for composting [29] [30]. As shown in Figure 2 and Figure 3. The ammonia nitrogen decreased with time, while the nitrate nitrogen increases with time, which indicate that the nitrification process occurred [30].
From the above results the nitrification ratio is calculated and presented in Table 7. Some studies indicate that the ratio should not exceed 0.16 [31], while others reported ratios of 1 [29].
The results indicate that that nitrification ratios are high at the beginning of the treatments and decreased until maturity is reached. All treatments have a
![]()
Table 6. Results of total nitrogen.
![]()
Figure 2. Ammonium nitrogen in different compost treatments.
![]()
Figure 3. Nitrate nitrogen in different compost treatments.
![]()
Table 7. Types of rocks used and their corresponding quantities.
nitrification ratio below 1. Treatments inoculated with EM (T6, T3, T9) have a nitrification ratio below 0.16. These results indicate that these treatments have highest maturity compared to other treatments.
3.4. C/N Ratio
The carbon to nitrogen ratio (C/N) is one of the most important factors that affect the composting process. In this experiment C/N ratio is used to follow the degradation process of the compost piles as done in many other studies despite many pitfalls associated with this approach [32]. The C/N ratio is calculated and presented in Figure 4. The results indicate that C/N ratio of all piles are close or below 20 after 60 days of compositing, which is an indication of acceptable maturity [32] [33].
3.5. Moisture Content and Bulk Density
The moisture content and bulk density were measured for all piles as presented in Figure 5 and Figure 6 respectively.
The moisture content of all treatments initially ranged from 60% - 67% and
![]()
Figure 4. C/N ratio of different compost treatments.
![]()
Figure 5. Moisture content in different compost treatments.
![]()
Figure 6. Bulk density of different compost treatments.
decreased during the composting process to reach values in the range of 30% to 38%. The bulk densities were initially 285 kg/m3, 320 kg/m3, 300 kg/m3, 210 kg/m3 and 290 kg/m3 280 kg/m3, 310 kg/m3, 320 kg/m3, 270 kg/m3 respectively. These values increased to 445 kg/m3, 533 kg/m3, 470 kg/m3, 420 kg/m3, 536 kg/m3, 480 kg/m3, 494 kg/m3, 552 kg/m3, 466 kg/m3 respectively.
One-way ANOVA was performed on the data of bulk density after 60 days and results indicate that p-value of 0.00 less than 0.05 confidence interval, which means that there is a significant difference between the means of different treatments.
The pile inoculated with EM and 10% biochar (T6) showed highest bulk density. High bulk density values indicate higher level of activities in the decomposition of organic material to break down the loosely combined raw materials into smaller pieces [3]. This result indicates that T6 have the highest level of activities in the decomposition of organic material to break down the loosely combined raw materials into smaller pieces compared to all other treatments.
3.6. pH and Electrical Conductivity (Ec)
The electrical conductivity (EC) and pH of all piles were measured and presented in Figure 7 and Figure 8 respectively.
EC is a good indicator of the safety and suitability of compost. The EC of the finished compost of all treatments are ranging between 2.3 to 3.12 dS∙m−1. Some studies showed that values ranging between 2.0 to 6.0 dS∙m−1 are considered tolerable by plants [34] [35].
Also, the pH values of all piles after 90 days were ranging from 7.74 to 8.69, which is in the recommended range from 7.5 to 8.5 [27].
3.7. Germination Index (GI), Pathogenic Bacteria and Humification Index (HI)
Germination index (GI) is a measure of phytotoxicity of compost; many studies
![]()
Figure 7. Electrical Conductivity of different compost treatments.
![]()
Figure 8. pH of different compost treatments.
![]()
Table 8. Germination Index and humification index for different treatments after 90 days of composting
reported that a GI higher than 80% indicates the absence of phytotoxins in composts [3] [29]. According to Selim et al., GI ranging from 66 to 100 indicates absence of phytotoxicity [29]. The GI of all treatments is presented in Table 8. GI of all treatments are ranging from 80 to 90, which indicates that all compost piles are free of phytotoxins.
The humification index (HI) is the ratio of the humic acid to the fulvic acid and is a measure of maturity of the compost. The recorded HI is greater than 1 for all treatments as presented in Table 8; therefore, all compost piles could be considered mature.
All final compost treatments were found free of pathogenic bacteria, as presented in Table 9, indicating their biosafety.
3.8. Total Phosphorous (TP) and Total Potassium (TK)
%TP and %TK were measured for all piles. Three measurements were taken for each pile. The average TP(%) and TK(%) values are presented in Table 10 respectively. According to El-Haddad et al. [36], the recommended range of TP (%) is 0.4 to 1.1 and the recommended range of TK (%) is 0.6 to 1.7. The %TP and %TK of all treatments increased in the compost piles and were in final product in the recommended range (TP (%) is 0.4 to 1.1 and TK (%) is 0.6 to 1.7).
One-way ANOVA analysis of %TP and %TK after 60 days indicate that
![]()
Table 9. Pathogenic bacteria for different treatments.
nd refers to not detected.
p-value of 0.00 less than 0.05 confidence interval, which means that there is a significant difference between the means of different treatments, which means that each additive has a different effect on the final %TP and %TK of compost pile.
Table 10 compares the values of TP and TK by weight (in kg). The results are in line with results obtained from the %TP and %TK. There is an increase in total phosphorous and total potassium values during composting.
The highest values were obtained in T6 containing EM and 10% biochar. It is also important to notice that increasing the percentage of biochar to 10% has
increased the quality of the compost. However, further increase of biochar to 20% decreased the quality of the compost.
4. Conclusion
The results revealed that the application of different additives in composting of rice straw exhibits an improvement in maturation time and final product quality. In fact, all piles reached maturation after around 42 days. All analysis of the properties of the final products indicated that it was in the range of the matured level and can be used without any limitation as an organic fertilizer. The highest decomposition rate and highest organic fertilizer quality were obtained in pile containing rice straw and 40% of animal manure mixed with natural rocks (2.5% of rock phosphate, 2.5% feldspar, 2.5% sulfur, 2.5% dolomite and 10% bentonite) and inoculated with 2% of EM and 10% biochar compared to other treatments. Also, the results showed that adding 20% biochar decreased the quality of the final compost compared to adding 10%.