Modelling and Simulation of Cutting Forces in Micromachining

Shah Md. Mahfuzur Rahman; Jong Leng Liow

doi:10.4028/www.scientific.net/KEM.443.652

Paper Titles

Evaluation of Novel Approach on Delamination Factor after Drilling Composite Laminates
p.626

Process Technology and Performance Evaluation of Nylon 6/PU Stab Resistance Fabric Matrix
p.631

Machining of Micro-Channels on Brittle Glass Using an Abrasive Slurry Jet
p.639

A Study of Abrasive Jet Micro-Grooving of Quartz Crystals
p.645

Modelling and Simulation of Cutting Forces in Micromachining
p.652

Experimental Study on the Chip Geometry and Shear Angle in Micro-Cutting Aluminum 7050-T7451
p.657

Finite Element Analysis of Micro-Cutting Aluminum 7050-T7451 with the Tool Edge Radius Considered
p.663

Design of a Fast Tool Servo Based Diamond Turning Machine for Fabricating Micro-Structured Surfaces
p.669

Erosion Mechanism of Ultrasonic Vibration Abrasive Waterjet in Micro Machining
p.675

HomeKey Engineering MaterialsKey Engineering Materials Vol. 443Modelling and Simulation of Cutting Forces in...

Modelling and Simulation of Cutting Forces in Micromachining

Abstract:

The analysis of cutting forces plays an important role in the design of machine tool systems as well as in the planning, optimization, and control of micro machining processes. Several parameters influence the cutting forces of which the friction is important in causing premature tool failure. This paper presents a force model that includes the friction force for sliding due to the contact between the tool and workpiece at the flank face. Simulation results were compared with the experimental results of Bao and Tansel [1] showing that the model can satisfactorily represent the cutting forces in two dimensional cutting.

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Key Engineering Materials (Volume 443)

Pages:

652-656

DOI:

https://doi.org/10.4028/www.scientific.net/KEM.443.652

Citation:

Cite this paper

Online since:

June 2010

Authors:

Shah Md. Mahfuzur Rahman, Jong Leng Liow

Keywords:

Cutting Force, Friction, Micro End Milling, Modeling

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

References

[1] W. Y. Bao and I. N. Tansel: International Journal of Machine Tools and Manufacture, Vol. 40 (2000), p.2155.

Google Scholar

[2] C. Li, Xinmin Lai, Hongtao Li and Jun Ni: J. Micromech. Microeng, Vol. 17 (2007), p.671.

Google Scholar

[3] H. Weule, et al.: CIRP Annals - Manufacturing Technology, Vol. 50 (2001), p.61.

Google Scholar

[4] M. E. Martellotti: Trans. of ASME, Vol. 63 (1941), p.677.

Google Scholar

[5] J. Tlusty and P. MacNeil: Annals of the CIRP, Vol. 24 (1975), p.21.

Google Scholar

[6] W. A. Kline, et al.: International Journal of Machine Tool Design and Research, Vol. 22 (1982), p.7.

Google Scholar

[7] M. P. Vogler, Richard E. DeVor and Shiv G. Kapoor: Journal of Manufacturing Science and Engineering Vol. 125 (2003), p.202.

Google Scholar

[8] M. P. Vogler, Richard E. DeVor and Shiv G. Kapoor: Journal of Manufacturing Science and Engineering Vol. 126 (2004), p.685.

Google Scholar

[9] M. T. Zaman, et al.: International Journal of Machine Tools & Manufacture, Vol. 46 (2006), p.353.

Google Scholar

[10] I. S. Kang, et al.: Journal of Materials Processing Technology, Vol. 187-188 (2007), p.250.

Google Scholar

[11] C. Arcona and T. A. Dow: Journal of Manufacturing Science and Engineering, Vol. 120 (1998).

Google Scholar