Effect of Annealing on Microstructure of Hydroxyapatite Coatings and their Behaviours in Simulated Body Fluid

Sharidah Azuar Abdul Azis; John Kennedy; Peng Cao

doi:10.4028/www.scientific.net/AMR.922.657

Paper Titles

Effect of Uniaxial Compressive Stress during Formation of Porous Aluminum by Mechanochemical Reaction on its Mechanical Properties
p.632

Variation of Mechanical Properties of AlSi20Cu2Ni1 Alloy with Co Addition and Ultrasonic Treatment
p.638

Determination of Substitutional-Interstitial Interaction from Chemical Potentials of Interstitials in the Steel Matrix
p.645

Structure and Properties of Cu Alloys Alloying with Cr and Hf after Equal Channel Angular Pressing
p.651

Effect of Annealing on Microstructure of Hydroxyapatite Coatings and their Behaviours in Simulated Body Fluid
p.657

Influence of Filler Rod Composition on the Strength of Tungsten Inert Gas Welded Magnesium Alloy Joint
p.663

Microstructure of Er₂O₃Coating Layer of Hydrogen Penetration Control
p.667

Design and Fabrication of New Ti-Based Ternary Metallic Glasses Based on Effective Atomic Radius in the Ti Solid Solution Calculated by Ab Initio Calculation
p.671

The Correlation between Stacking Fault Energy and the Work Hardening Behaviour of High-Mn Twinning Induced Plasticity Steel Tested at Various Temperatures
p.676

HomeAdvanced Materials ResearchAdvanced Materials Research Vol. 922Effect of Annealing on Microstructure of...

Effect of Annealing on Microstructure of Hydroxyapatite Coatings and their Behaviours in Simulated Body Fluid

Abstract:

In this study, hydroxyapatite (HA) coatings on Ti6Al4V substrate were deposited using an ion beam sputtering technique. Owing to its medical applications, the crystalline phases present in the HA must be controlled. This study investigated the effect of post-deposition heat treatment at different temperatures and evaluated the microstructure of the HA coatings and their behaviours in simulated body fluid (SBF). The post-deposition treatment of the as-deposited samples was carried out in an air-circulated furnace at a temperature between 300 ⁰C and 600 ⁰C. The XRD patterns reveal that the minimum temperature to transform the HA coating from amorphous to crystalline phase is 400 ⁰C. A higher temperature at 600 ⁰C leads to a growth of the crystalline HA phases. Fourier transform infrared spectroscopy (FTIR) measurements show the existence of hydroxyl and PO-bonds in all coatings and the amounts varied with temperature. Atomic Force Microscopy (AFM) study suggests that the nanostructured crystalline HA starts to grow at 400 ⁰C and becomes more obvious at a higher temperature of 600 ⁰C. The simulated body fluid (SBF) test reveals that better apatite formation with post deposition heat treatment at 600 ⁰C would potentially enhance the formation of new bone (osseointegration).

You might also be interested in these eBooks

View Preview

Info:

Periodical:

Advanced Materials Research (Volume 922)

Pages:

657-662

DOI:

https://doi.org/10.4028/www.scientific.net/AMR.922.657

Citation:

Cite this paper

Online since:

May 2014

Authors:

Sharidah Azuar Abdul Azis*, John Kennedy, Peng Cao

Keywords:

Hydroxyapatite (HA), Ion Beam Sputtering, Simulated Body Fluid, Ti6Al4V

Export:

RIS, BibTeX

Price:

Permissions:

Request Permissions

* - Corresponding Author

References

[1] Y. Yang, K. H Kim, J. L. Ong, A review on calcium phosphate coatings produced using a sputtering process—an alternative to plasma spraying, Biomaterials 26 (2005) 327–37.

DOI: 10.1016/j.biomaterials.2004.02.029

Google Scholar

[2] L. Yan, Y. Leng, L.T. Weng, Characterization of chemical inhomogeneity in plasma-sprayed hydroxyapatite coatings, Biomaterials 24 (2003) 2585.

DOI: 10.1016/s0142-9612(03)00061-9

Google Scholar

[3] J.L. Ong, C. N. Chan, Hydroxyapatite and their use as coatings in dental implants: a review, Crit Rev Biomed Eng. 28 (1999) 667–707.

DOI: 10.1615/critrevbiomedeng.v28.i56.10

Google Scholar

[4] M.J. Filiaggi, N.A. Coombs, R.M. Pilliar, Characterization of the interface in the plasma-sprayed HA coating/Ti-6Al-4V implant system, J. Biomed. Mater. Res. 25 (1991) 1211–29.

DOI: 10.1002/jbm.820251004

Google Scholar

[5] O. Lyngnes, N. Traggis, K.L. Dessau, & C. Myatt, Coating Technologies for High Damage-Threshold Optics, Opt. Photon. News, 17(6) (2006) 28-33.

DOI: 10.1364/opn.17.6.000028

Google Scholar

[6] J.Breme, Y.Zhou, L. Groh, Development of titanium alloy suitable for an optimized coating with hydroxyapatite, Biomaterials 3 (1995) 239-244.

DOI: 10.1016/0142-9612(95)92123-n

Google Scholar

[7] B. León, J. Jansen, Thin calcium phosphate coatings for medical implants. (2009)

Google Scholar

[8] J.L. Ong, L.C. Lucas, W.R. Lacefield, E.D. Rigney, Structure, solubility and bond strength of thin calcium phosphate coatings produced by ion beam sputter deposition, Biomaterials 13(4) (1992) 249-254.

DOI: 10.1016/0142-9612(92)90192-q

Google Scholar

[9] J. Kennedy, J. Pithie, A. Markwitz, Characteristics of hetero-junction diodes based on ion beam sputtered ZnO thin films, Proceedings of SPIE - The International Society for Optical Engineering, (2008) 6800, 68001P.

DOI: 10.1117/12.768752

Google Scholar

[10] P.P. Murmu, J. Kennedy, B.J. Ruck, A. Markwitz, Characterization of the structural and electrical properties of ion beam sputtered ZnO films, Materials Science Forum 700, (2012) 49-52.

DOI: 10.4028/www.scientific.net/msf.700.49

Google Scholar

[11] M. Yoshinari, Y. Oda, T. Kato, K.Okuda, Influence of surface modifications to titanium on antibacterial activity in vitro, Biomaterials 22(14) (2001) 2043-2048.[12] S. Dorozhkin, Calcium orthophosphates, J Mater Sci. 42(4) (2007) 1061-95.

DOI: 10.1016/s0142-9612(00)00392-6

Google Scholar