CNT/PDMS柔性传感材料的打印工艺及性能研究

doi:10.3901/JME.2020.15.097

机械工程学报 ›› 2020, Vol. 56 ›› Issue (15): 97-103.doi: 10.3901/JME.2020.15.097

• 特邀专栏：4D打印技术 • 上一篇下一篇

扫码分享

CNT/PDMS柔性传感材料的打印工艺及性能研究

徐雪杰^1,2, 朱子才^1,2, 罗斌^1,2, 何青松³

1. 西安交通大学机械工程学院西安 710049;
2. 西安交通大学机械强度与振动国家重点实验室西安 710049;
3. 南京航空航天大学机电学院南京 210016

收稿日期:2019-07-06 修回日期:2019-09-28 出版日期:2020-08-05 发布日期:2020-10-19
通讯作者: 朱子才(通信作者),男,1984年生,博士,副教授,硕士研究生导师。主要研究方向为智能材料的驱动/传感一体化。E-mail:649018251@qq.com
作者简介:徐雪杰,男,1993年出生。主要研究方向为智能材料与结构的增材制造技术。E-mail:xxjzzz@stu.xjtu.edu.cn
基金资助:
国家自然科学基金重大研究计划资助项目（91648110）。

Research on Printing Process and Perfomance of CNT/PDMS Soft Sensing Material

XU Xuejie^1,2, ZHU Zicai^1,2, LUO Bin^1,2, HE Qingsong³

1. School of Mechanical Engineering, Xi'an Jiaotong University, Xi'an 710049;
2. State Key Laboratory of Mechanical Structural Strength and Vibration, Xi'an Jiaotong University, Xi'an 710049;
3. College of Mechanical & Electrical Engineering, Nanjing University of Aeronautics and Astronautics, Nanjing 210016

Received:2019-07-06 Revised:2019-09-28 Online:2020-08-05 Published:2020-10-19

摘要/Abstract

摘要： 针对复合导电材料CNT/PDMS应用于柔性传感以及复杂结构设计的需求，将直写打印技术与该复合导电材料的成型制备方法结合起来，研究了CNT/PDMS复合材料的打印工艺和电阻传感性能。在试验研究中，首先配置了不同CNT含量的打印墨水，并对打印墨水的流变性及材料导电性进行测试，试验结果表明配置的打印墨水均具有粘弹性以及剪切变稀的性质，其中以CNT质量分数为7%的墨水用于直写打印时兼具导电性好易挤出且成型好的特点。通过单点成线试验，设置3D打印机参数为：扫描速度为10 mm/s，挤出气压为0.3 MPa。在此基础上，进行简单平面条状、二维网状结构以及立体网格结构的打印，对打印的条状结构进行温度和单轴拉伸试验，在不同的温度和拉伸率下打印件均表现有电阻传感特性；对网格状电路进行柔性电路性能测试，在对其施加6 V左右电压时，无论网格电路处于伸展还是弯曲状态均能表现出良好的导电性能；对打印的立体网格结构进行压力传感试验，结果表明复合材料有良好的压敏特性。性能表征结果证明该打印工艺可行，从而为后续该材料的复杂结构制造以及在柔性传感电子设备中的应用奠定基础。

关键词: 增材制造, 柔性电路, 电阻传感, 直写打印

Abstract: According to the requirements of the application of CNT/PDMS in soft ciruit and complex structure design, the direct writing printing technology is combined with the molding preparation method of the hybrid conductive material, and the printing process of CNT/PDMS is studied. Firstly, the printing ink of mixed materials with different CNT content is configured, and the rheological property and material conductivity are measured. All the printing inks are shear thinned and viscoelastic, among which the printing ink with CNT content of 7% is of good conductivity, easy to extrude and formed. The printer parameters are set as follows: scanning speed is 10 mm/s, extrusion pressure is 0.3 MP, and the printing process is stable. On this basis, the simple planar strip, two-dimensional mesh structure and three-dimensional grid structure are printed, and the temperature and uniaxial tensile experiments are carried out on the printed strip structure. The printed sample shows resistance sensing characteristics at different temperatures and tensile rates. The flexible circuit performance of the grid-like circuit is tested. When the voltage of about 6 V is applied, the grid-like circuit shows good electrical conductivity in the stretching or bending state. The pressure sensing experiment on the printed 3D grid structure shows that the composite material with good pressure sensitivity. The results of performance characterization proves that the printing process is feasible, which laid a foundation for the subsequent complex structure manufacturing of the material and its application in flexible sensing electronic equipment.

Key words: additive manufacturing, soft circuit, resistance sensor, direct writing printing

中图分类号:

TP24
TP331

徐雪杰, 朱子才, 罗斌, 何青松. CNT/PDMS柔性传感材料的打印工艺及性能研究[J]. 机械工程学报, 2020, 56(15): 97-103.

XU Xuejie, ZHU Zicai, LUO Bin, HE Qingsong. Research on Printing Process and Perfomance of CNT/PDMS Soft Sensing Material[J]. Journal of Mechanical Engineering, 2020, 56(15): 97-103.

参考文献

[1] XU S,ZHANG L,JIA L,et al. Soft microfluidic assemblies of sensors,circuits,and radios for the skin[J]. Science,2014,344(6179):70-74.
[2] YAMADA T,HAYAMIZU Y,YAMAMOTO Y,et al. A stretchable carbon nanotube strain sensor for human-motion detection[J]. Nature Nanotechnology,2011,6(5):296-301.
[3] PANG C,LEE G Y,KIM T,et al. A flexible and highly sensitive strain-gauge sensor using reversible interlocking of nanofibres[J]. Nature Materials,2012,11(9):795-801.
[4] SOMEYA T,KATO Y,SEKITANI T,et al. Conformable,flexible,large-area networks of pressure and thermal sensors with organic transistor active matrixes[J]. Proceedings of the National Academy of Science of the United Sattes of America,2005,102(35):12321-12325.
[5] TAKEI K,TAKAHASHI T,HO J C,et al. Nanowire active-matrix circuitry for low-voltage macroscale artificial skin[J]. Nature Materials,2010,9(10):821-826.
[6] LIPOMI D J,VOSGUERITCHIAN M,TEE B C,et al. Skin-like pressure and strain sensors based on transparent elastic films of carbon nanotubes[J]. Nature Nanotechnology,2011,6(12):788-792.
[7] KIM J,LEE M,SHIM H J,et al. Stretchable silicon nanoribbon electronics for skin prosthesis[J]. Nature Communications,2013,5(5):3773-3778.
[8] GAO W S, EMAMINEJAD H Y, NYEIN Y,et al. Fully integrated wearable sensor arrays for multiplexed in situ perspiration analysis[J]. Nature,2016,529(7587):509-514.
[9] XU S,ZHANG Y,CHJ O,et al. Stretchable batteries with self-similar serpentine interconnects and integrated wireless recharging systems[J]. Nature Communications,2013,4(2):836-839.
[10] KALTENBRUNNER M,SEKITANI T,REEDER J,et al. An ultra-lightweight design for imperceptible plastic electronics[J]. Nature,2013,499(7459):458-463.
[11] SO J H,THELEN J,QUSBA A,et al. Reversibly deformable and mechanically tunable fluidic antennas[J]. Advanced Functional Materials,2010,19(22):3632-3637.
[12] OTA H,CHEN K,LIN Y,et al. Highly deformable liquid-state heterojunction sensors[J]. Nature Communications,2014,5(1):494-499.
[13] CHEN L Z,LIU C H,HU C H,et al. Electrothermal actuation based on carbon nanotube network in silicone elastomer[J]. Appl. Phys. Lett.,2008,92(26):263104.
[14] PIERRE A,SADEGHI M,PAYNE M M,et al. All-printed flexible organic transistors enabled by surface tension-guided blade coating[J]. Advanced Materials,2014,26(32):5722-5727.
[15] ZHANG D,CHI B,LI B,et al. Fabrication of highly conductive graphene flexible circuits by 3D printing[J]. Synthetic Metals,2016,217:79-86.
[16] JUNG H C,MOON J H,BAEK D H,et al. CNT/PDMS composite flexible dry electrodes for long-term ECG Monitoring[J]. IEEE Trans. Biomed Eng.,2012,59(5):1472-1479.
[17] 徐雪杰,罗斌,陈花玲. 光驱动软体结构增材制造工艺研究[J]. 西安交通大学学报,2018(8):54-59. XU Xuejie,LUO Bin,CHEN Hualing. Research on additive manufacturing technology of optical drive software structure[J]. Journal of Xi'an Jiaotong University,2018(8):54-59.
[18] 罗斌,夏华翅,陈花玲. 离子凝胶材料的三维打印工艺[J]. 机械工程学报,2018,54(17):157-164. LUO Bin,XIA Huachi,CHEN Hualing. Study on 3D printing technology of ionic gel materials[J]. Journal of Mechanical Engineering,2018,54(17):157-164.
[19] BOLEY J W,WHITE E L,KRAMER R K. Mechanically sintered gallium-indium nanoparticles[J]. Advanced Materials,2015,27:2355-2360.
[20] VALENTINE A D,BUSBEE T A,BOLEY J W,et al. Hybrid 3D printing of soft electronics[J]. Advanced Materials,2017,29(40):1703817.
[21] JUNG H C,MOON J H,BAEK D H,et al. CNT/PDMS composite flexible dry electrodes for long-term ECG monitoring[J]. IEEE Transactions on Biomedical Engineering,2012,59(5):1472-1479.
[22] LIU C X,CHOI J W. Strain-dependent resistance of PDMS and carbon nanotubes composite microstructures[J]. IEEE Transactions on Nanotechnology,2010,9(5):590-595.
[23] LI K,WEI H,LIU W,et al. 3D printed stretchable capacitive sensors for highly sensitive tactile and electrochemical sensing[J]. Nanotechnology,2018,29(18),185501.
[24] KIM J H,HWANG J Y,HWANG H R,et al. Simple and cost-efective method of highly conductive and elastic carbon nanotube/polydimethylsiloxane composite for wearable electronics[J]. Scientific Reports,2018,8:1-11.

CNT/PDMS柔性传感材料的打印工艺及性能研究

Research on Printing Process and Perfomance of CNT/PDMS Soft Sensing Material

PDF

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

[1]	林坷升, 刘洁, 刘方政, 康红磊, 李锋, 史玉升. 油墨直写打印纳米羟基磷灰石/聚乳酸复合材料：制备及性能研究[J]. 机械工程学报, 2020, 56(9): 234-242.
[2]	朱东彬, 吴民强, 王竹贤, 杨伟东. 基于微滴喷射3D打印的纳米颗粒悬浮墨水稳定喷射研究[J]. 机械工程学报, 2020, 56(9): 243-251.
[3]	高炼玲, 余圣甫, 禹润缜, 何天英, 史玉升. 5356铝合金过渡端框电弧增材制造及组织与性能[J]. 机械工程学报, 2020, 56(8): 28-36.
[4]	葛福国, 彭倍, 柯文超, 敖三三, 从保强, 祁泽武, 曾志. 电弧增材制造NiTi形状记忆合金成形与性能[J]. 机械工程学报, 2020, 56(8): 99-106.
[5]	李文涛, 周正干. 激光增材制造钛合金构件的阵列超声检测方法研究[J]. 机械工程学报, 2020, 56(8): 141-147.
[6]	史玉升, 伍宏志, 闫春泽, 杨潇, 陈道兵, 张策, 苏彬, 宋波, 李中伟, 庞盛永, 文世峰, 梁波, 赵清亮, 贺健康, 张述泉, 温银堂. 4D打印——智能构件的增材制造技术[J]. 机械工程学报, 2020, 56(15): 1-25.
[7]	方学伟, 白浩, 姚云飞, 张丽娟, 卢秉恒. 冷金属过渡电弧增材制造多道搭接工艺研究[J]. 机械工程学报, 2020, 56(1): 141-147.
[8]	陈嵩涛, 段庆林, 王依宁, 李书卉, 李锡夔. 选区激光烧结过程传热分析的高效无网格法[J]. 机械工程学报, 2019, 55(7): 135-146.
[9]	罗怡, 朱亮, 韩静韬, 许洁, 张成洋. 电弧填丝增材制造过程熔滴射滴过渡特征及其对熔滴沉积成形的影响[J]. 机械工程学报, 2019, 55(3): 219-225.
[10]	王忠睿, 苗恺, 朱伟军, 李涤尘. 基于立体光固化3D打印的一体化石膏铸型的高温力学性能研究[J]. 机械工程学报, 2019, 55(23): 182-188.
[11]	许权, 兰红波, 赵佳伟, 杨昆, 朱晓阳. 基于电场驱动熔融沉积直写和微转印大面积透明电极制造[J]. 机械工程学报, 2019, 55(23): 216-225.
[12]	刘伟, 李能, 周标, 张国栋, 梁家誉, 郑涛, 熊华平. 复杂结构与高性能材料增材制造技术进展[J]. 机械工程学报, 2019, 55(20): 128-151,159.
[13]	常树鹤, 张昊宇, 许海鹰, 洪宇翔, 王力, 都东. 基于视觉信息融合的熔丝成形制造路径在线识别[J]. 机械工程学报, 2019, 55(17): 1-7.
[14]	亓欣波, 李长鹏, 李阳, 林峰, 李勇, 程宣, 陈国锋. 基于机器学习的电子束选区熔化成形件密度预测[J]. 机械工程学报, 2019, 55(15): 48-55.
[15]	朱伟军, 陈言坤, 张志坤, 田小永, 李涤尘. 可拉伸柔性电路的原位封装3D打印工艺[J]. 机械工程学报, 2019, 55(15): 64-70.