Abstract
We investigated the electrical conductivity and percolation behavior of binary and ternary nanocomposites based on multiwalled carbon nanotubes (MWCNs) using polypropylene (PP) and a blend of PP with cyclic butylene terephthalate (CBT). The nanocomposites were prepared by diluting a commercial 20 %wtMWCNT PP masterbatch using optimized melt-mixing conditions. The concentration of carbon nanotubes in the diluted PP samples was as low as 0.5 % and as high as 15 % in weight. For the PP/CBT blend CBT concentration was varied up to 40 %wt while the loading of CNT was from 0 to 5 %wt. SEM and TEM techniques were used to examine the quality of the dispersion and the formation of nanotube networks within the polymer matrix. TEM and Raman spectroscopy results showed that for the diluted PP/MWCNT composites the nanotubes are well aligned in samples obtained the microinjection molding process, although the level of alignment is less with crystalline PP than in an amorphous matrix such as polycarbonate (PC). FTIR and XRD results revealed that the orientation of both polymer chains and crystals decreased with the incorporation of nanotubes into PP. The electrical conductivity was also significantly altered by the nanotube alignment in a PP matrix, as was previously observed for PC/MWCNT composites; the conductivity decreased and the percolation threshold rose in highly sheared samples; however, the presence of a crystalline phase improved the conductivity even for high shear conditions through the phenomenon of double percolation threshold. This last concept refers to the requirement that the filler-rich phase be continuous and conductive and not to the existence of two percolation thresholds at two different CNT concentrations. The electrical conductivity of PP/CBT blends was also improved through a double percolation that is the basic requirement for the conductivity of the ternary nanocomposites.
References
Abbasi, S., Carreau, P. J., Derdouri, A. and Moan, M., “Rheological Properties and Percolation in Suspensions of Multiwalled Carbon Nanotubes in Polycarbonate”, Rheol. Acta., 48, 943–959 (2009) DOI: http://dx.doi.org/10.1007/s00397-009-0375-7Search in Google Scholar
Abbasi, S., Carreau, P. J. and Derdouri, A., “Flow Induced Orientation of Multiwalled Carbon Nanotubes in Polycarbonate Nanocomposites: Rheology, Conductivity and Mechanical Properties”, Polymer, 51, 922–935 (2010) DOI: http://dx.doi.org/10.1016/j.polymer.2009.12.041Search in Google Scholar
Abbasi, S., Derdouri, A. and Carreau, P. J., “Properties of Microinjection Molding of Polymer Multiwalled Carbon Nanotube Conducting Composites”, Polym. Eng. Sci.51, 992–1003 (2011) DOI: http://dx.doi.org/10.1002/pen.21904Search in Google Scholar
Al-Salah, M. H., Al-Anid, H. K. and Hussain, Y. A., “Electrical Double Percolation and Carbon Nanotubes Distribution in Solution Processed Immiscible Polymer Blend”, Synth. Met., 175, 75–80 (2013) DOI: http://dx.doi.org/10.1016/j.synthmet.2013.05.004Search in Google Scholar
Bhagat, N. A., Shrivastava, N. K., Suin, S., Maiti, S. and Khatua, B. B., “Development of Electrical Conductivity in PP/HDPE/MWCNT Nanocomposites by Melt Mixing at Very Low Loading of MWCNT”, Polym. Compos., 34, 787–798 (2013) DOI: http://dx.doi.org/10.1002/pc22491Search in Google Scholar
Breuer, O., Tchoudakov, R., Narkis, M. and Siegmann, A., “Shear Rate Effect on the Resistivity of HIPS/LLDPE/Carbon Black Extrudates”, Polym. Eng. Sci., 38, 1898–1905 (1998) DOI: http://dx.doi.org/10.1002/pen.10360Search in Google Scholar
Bueche, F., “Electrical Resistivity of Conducting Particles in an Insulating Matrix”, J. Appl. Phys., 43, 4837–4838 (1972) DOI: http://dx.doi.org/10.1063/1.1661034Search in Google Scholar
Bulusheva, L. G., Okotrub, A. V., Kinloch, I. A., Asanov, I. P., Kurenya, A. G., Kudashov, A. G., Cheng, X. and Song, H., “Effect of Nitrogen Doping on Raman Spectra of Multi-Walled Carbon Nanotubes”, Phys. Status Solidi B, 245, 1971–1974 (2008) DOI: http://dx.doi.org/10.1002/pssb.200879592Search in Google Scholar
Cadek, M., Coleman, J. N., Barron, V., Hedicke, K. and Blau, W. J., “Morphological and Mechanical Properties of Carbon-Nanotube-Reinforced Semi-Crystalline and Amorphous Polymers”, Appl. Phys. Lett., 81, 5123–5125, (2002) DOI: http://dx.doi.org/10.1063/1.1533118Search in Google Scholar
Chang, T. E., Jensen, L. R., Kisliuk, A., Pipes, R. B., Pyrz, R. and Sokolov, A. P., “Microscopic Mechanism of Reinforcement in Single-Wall Carbon Nanotube/Polypropylene Nanocomposite”, Polymer, 46, 439–444 (2005) DOI: http://dx.doi.org/10.1016/J.Polymer.2004.11.030Search in Google Scholar
Clarke, J., Clarke, B., Freakley, P. K. and Sutherland, I., “Compatibilising Effect of Carbon Black on Morphology of NR–NBR Blends”, Plast. Rub. Compos., 30, 39–44 (2001) DOI: http://dx.doi.org/10.1179/146580101101541426Search in Google Scholar
Dresselhaus, M. S., Dresselhaus, G. and Saito, R., “Physics of Carbon Nanotubes”, Carbon, 33, 883–891 (1995) DOI: http://dx.doi.org/10.1016/0008-6223(95)00017-8Search in Google Scholar
Du, F., Scogna, R. C., Zhou, W., Brand, S., Fischer, J. E. and Winey, K. I., “Nanotube Networks in Polymer Nanocomposites: Rheology and Electrical Conductivity”, Macromolecules, 37, 9048–9055 (2004) DOI: http://dx.doi.org/10.1021/ma049164gSearch in Google Scholar
Endo, M., Kim, Y. A., Fukai, Y., Hayachi, T., Terrones, M., Terrones, H. and Dresselhaus, M. S., “Comparison Study of Semi-Crystalline and Highly Crystalline Multiwalled Carbon Nanotubes”, Appl. Phys. Lett., 79, 1531–1533 (2001) DOI: http://dx.doi.org/10.1063/1.1400774Search in Google Scholar
Fenouillot, F., Cassagnau, P. and Majesté, J.-C., “Uneven Distribution of Nanoparticles in Immiscible Fluids: Morphology Development in Polymer Blends”, Polymer, 50, 1333–1350 (2009) DOI: http://dx.doi.org/10.1016/j.polymer.2008.12.029Search in Google Scholar
Fischer, D., Pötschke, P., Brüning, H. and Janke, A., “Investigation of the Orientation in Composite Fibers of Polycarbonate with Multiwalled Carbon Nanotubes by Raman Microscopy”, Macromol. Symp., 230, 167–172 (2005) DOI: http://dx.doi.org/10.1002/masy.200551156Search in Google Scholar
Göldel, A., Kasaliwal, G. and Pötschke, P., “Selective Localization and Migration of Multiwalled Nanotubes in Blends of Polycarbonate and Poly(styrene acrylonitrile)”, Macromolecular Rapid Com., 30, 423–429 (2009) PMid:21706619; DOI: http://dx.doi.org/10.1002/marc.200800549Search in Google Scholar
Göldel, A., Kasaliwal, G. R., Pötschke, P. and Heinrich, G., “The Kinetics of CNT transfer between Immiscible Blend Phases during Melt Mixing”, Polymer, 53, 411–421 (2012) DOI: http://dx.doi.org/10.1016/j.polymer.2011.11.039Search in Google Scholar
Gubbels, F., Jerome, R., Vanlathem, E., Deltour, R., Blacher, S. and Brouers, F., “Kinetic and Thermodynamic Control of the Selective Localization of Carbon Black at the Interface of Immiscible Polymer Blends”, Chem. Mater., 10, 1227–1235 (1998) DOI: http://dx.doi.org/10.1021/cm970594dSearch in Google Scholar
Hobbs, S. Y., Dekkers, M. E. J. and Watkins, V. H., “Effect of Interfacial Forces on Polymer Blend Morphologies”, Polymer, 29, 1598–1602 (1988) DOI: http://dx.doi.org/10.1016/0032-3861(88)90269-8Search in Google Scholar
Hu, G., Zhao, C., Zhang, S., Yang, M. and Wang, Z., “Low Percolation Thresholds of Electrical Conductivity and Rheology in Poly(ethylene terephthalate) through the Networks of Multi-Walled Carbon Nanotubes”, Polymer, 47, 480–488 (2006) DOI: http://dx.doi.org/10.1016/j.polymer.2005.11.028Search in Google Scholar
Jeon, K., Lumata, L., Tokumoto, T., Steven, E., Brooks, J. and Alamo, R. G., “Low Electrical Conductivity Threshold and Crystalline Morphology of Single-Walled Carbon Nanotubes – High Density Polyethylene Nanocomposites Characterized by SEM, Raman Spectroscopy and AFM”, Polymer, 48, 4751–4764 (2007) DOI: http://dx.doi.org/10.1016/j.polymer.2007.05.078Search in Google Scholar
Karásek, L., Sumita, M., “Characterization of Dispersion State of Filler and Polymer-Filler Interactions in Rubber-Carbon Black Composites”, J. Mater. Sci.31, 281–289 (1996) DOI: http://dx.doi.org/10.1007/BF01139141Search in Google Scholar
Kharchenko, S. B., Douglas, J. F., Obrzut, J., Grulke, E. A. and Migler, K. B., “Flow-Induced Properties Of Nanotube-Filled Polymer Materials”, Nature Mater., 3, 564–568 (2004) PMid:15273745; DOI: http://dx.doi.org/10.1038/nmat1183Search in Google Scholar PubMed
Khunová, V., Smatko, V., Hudek, I. and Beniska, J., “Influence of Filler on the Polypropylene Structure”, Progr. Colloid Polym. Sci., 78, 188–191 (1988) DOI: http://dx.doi.org/10.1007/BFb0114372Search in Google Scholar
Kieth, H. P., Padden, Jr.F. J., “Sherulitic crystallization from the Melt. I. Fractionation and Impurity Segregation and their Influence on Crystalline Morphology”, J. Appl. Phys., 35, 1270–1285, (1964) DOI: http://dx.doi.org/10.1063/1.1713606Search in Google Scholar
Lee, G. W., Jagannathan, S., Chae, H. G., Minus, M. L. and Kumar, S., “Carbon Nanotube Dispersion and Exfoliation in Polypropylene and Structure and Properties of the Resulting Composites”, Polymer, 49, 1831–1840 (2008a) DOI: http://dx.doi.org/10.1016/j.polymer.2008.02.029Search in Google Scholar
LeeS.H., Kim, M. W., Kim, S. H. and Youn, J. R., “Rheological and Electrical Properties of Polypropylene/MWCNT Composites Prepared with MWCNT Masterbatch Chips”, Euro. Polym. J., 44, 1620–1630 (2008b) DOI: http://dx.doi.org/10.1016/j.eurpolymj.2008.03.017Search in Google Scholar
Lin, B., Sundararaj, U. and Pötschke, P., “Melt Mixing of Polycarbonate with Multi-Walled Carbon Nanotubes in Miniature Mixers”, Macromol. Mater. Eng., 291, 227–238 (2006) DOI: http://dx.doi.org/10.1002/mame.200500335Search in Google Scholar
Luongo, J. P., “Infrared Study of Polypropylene”, J. Appl. Polym. Sci., 3, 302–309 (1960) DOI: http://dx.doi.org/10.1002/app.1960.070030907Search in Google Scholar
Meincke, O., Kaempfer, D., Weickmann, H., Friedrich, H., Vathauer, M. and Warth, H., “Mechanical Properties and Electrical Conductivity of Carbon-Nanotube Filled Polyamide-6 and its Blends with Acrylonitrile/Butadiene/Styrene”, Polymer, 45, 739–748 (2004) DOI: http://dx.doi.org/10.1016/j.polymer.2003.12.013Search in Google Scholar
Meyyappan, M.: Carbon Nanotubes : Science And Applications, 1st Edition, CRC Press, Boca Raton (2005)Search in Google Scholar
Mičušîk, M., Omastová, M., Krupa, I., Prokeš, J., Pissis, P., Logakis, E., Pandis, C., Pötschke, P. and Piontek, J., “A Comparative Study on the Electrical and Mechanical Behaviour of Multi-Walled Carbon Nanotube Composites Prepared by Diluting a Masterbatch with Various Types of Polypropylenes”, J. Appl. Polym. Sci., 113, 2536–2551 (2009) DOI: http://dx.doi.org/10.1002/app.30418Search in Google Scholar
Moniruzzaman, M., WineyK.I., “Polymer Nanocomposites Containing Carbon Nanotubes”, Macromolecules, 39, 5194–5205 (2006) DOI: http://dx.doi.org/10.1021/ma060733pSearch in Google Scholar
Nielsen, L. E., Landel, R. F.: Mechanical Properties of Polymers and Composites, 2nd Edition, Marcel Dekker Publisher, New York (1993)Search in Google Scholar
Nordmark, T. S., Ziegler, G., “Spherulitic Crystallization of Gelatinized Maize Starch ans its Fractions”, Carbohydrate Polym., 49, 439–448 (2002) DOI: http://dx.doi.org/10.1016/S0144-8617(01)00353-8Search in Google Scholar
Nuriel, S., Liu, L., Barber, A. H. and Wagner, H. D., “Direct Measurement of Multiwall Nanotube Surface Tension”, Chem. Phys. Lett.404, 263–266 (2005) DOI: http://dx.doi.org/10.1016/j.cplett.2005.01.072Search in Google Scholar
Oda, Y., Hata, T., Preprints, 267, Seventeenth Annual Meeting of the High Polymer Society of Japan (1968)Search in Google Scholar
Owens, D. K., Wendt, R. C., “Estimation of the Surface Free Energy of Polymers”, J. Appl. Polym. Sci., 13, 1741–1747 (1969) DOI: http://dx.doi.org/10.1002/app.1969.070130815Search in Google Scholar
Painter, P. C., Watzek, M. and Koenig, J. L., “Fourrier Transform Infra-Red Study of Polypropylene”, Polymer, 18, 1169–1172 (1977) DOI: http://dx.doi.org/10.1016/0032-3861(77)90114-8Search in Google Scholar
Parthasarthy, G., Sevegney, M. and Kannan, R. M., “Rheooptical Fourier Transform Infrared Spectroscopy of the Deformation Behavior in Quenched and Slow-Cooled Isotactic Polypropylene Films”, J. Polym. Sci., Part B: Polym. Phys., 40, 2539–2551 (2002) DOI: http://dx.doi.org/10.1002/polb.10304Search in Google Scholar
Pham, G. T., Park, Y.-B., Wang, S., Liang, Z., Wang, B., Zhang, C., Funchess, B. and Kramer, L., “Mechanical and Electrical Properties of Polycarbonate Nanotube Buckypaper Composite Sheets”, Nanotechnology, 19, 325705 (2008) PMid:21828827; DOI: http://dx.doi.org/10.1088/0957-4484/19/32/325705Search in Google Scholar PubMed
Pötschke, P., Abdel-Goad, M., Alig, I., Dudkin, S., Lellinger, D., “Rheological and Dielectrical Characterization of Melt Mixed Polycarbonate-Multiwalled Carbon Nanotube Composites”, Polymer, 45, 8863–8870 (2004a) DOI: http://dx.doi.org/10.1016/j.polymer.2004.10.040Search in Google Scholar
PötschkeP., Bhattacharyya, A. R. and Janke, R., “Carbon-Nanotube Filled Polycarbonate Composites Produced by Melt Mixing and their Use in Blends with Polyethylene”, Carbon, 42, 965–969 (2004b) DOI: http://dx.doi.org/10.1016/j.carbon.2003.12.001Search in Google Scholar
Pötschke, P., Fornes, T. D. and Paul, D. R., “Rheological Behavior of Multiwalled Carbon Nanotube/Polycarbonate Composites”, Polymer, 43, 3247–3255 (2002) DOI: http://dx.doi.org/10.1016/S0032-3861(02)00151-9Search in Google Scholar
Pötschke, P., Kobashi, K., Villmow, T., Andres, T., Paiva, M. C. and Covas, J. A., “Liquid Sensing Properties of Melt Processed Polypropylene/Poly(∊-caprolactone) Blends Containing Multiwalled Carbon Nanotubes”, Compos. Sci. Technol., 71, 1451–1460 (2011) DOI: http://dx.doi.org/10.1016/j.compscitech.2011.05.019Search in Google Scholar
Pötschke, P., Brüning, H., Janke, A., Fischer, D. and Jehnichen, D., “Orientation of Multiwalled Carbon Nanotubes In Composites with Polycarbonate by Melt Spinning”, Polymer, 46, 10355–10363 (2005) DOI: http://dx.doi.org/10.1016/j.polymer.2005.07.106Search in Google Scholar
Pötschke, P., Kretzschmar, B., and Janke, A., “Use of Carbon Nanotube Filled Polycarbonate in Blends with Monmorillonite Filled Polypropylene”, Compos. Sci. Technol., 67, 855–860 (2007) DOI: http://dx.doi.org/10.1016/j.compscitech.2006.02.034Search in Google Scholar
Sadeghi, F., Ajji, A. and Carreau, P. J., “Analysis of Microporous Membranes Obtained from Polypropylene Films by Stretching”, J. Membr. Sci., 292, 62–71 (2007) DOI: http://dx.doi.org/10.1016/j.memsci.2007.01.023Search in Google Scholar
Sandler, J. K. W., Kirk, J. E., Kinloch, I. A., Shaffer, M. S. P. and Windle, A. H., “Ultra-Low Electrical Percolation Threshold in Carbon-Nanotube-Epoxy Composites”, Polymer, 44, 5893–5899 (2003) DOI: http://dx.doi.org/10.1016/S0032-3861(03)00539-1Search in Google Scholar
Sharples, A.: Introduction to Polymer Crystallization, 1st Edition, St. Martin's Press, New York (1966)Search in Google Scholar
Sumita, M., Abe, H., Kayaki, H. and Miyasaka, K., “Effect of Melt Viscosity and Surface Tension of Polymers on the Percolation Threshold of Conductive-Particle-Filled Polymeric Composites”, J. Macromol. Sci., Part B, 25, 171–184 (1986a) DOI: http://dx.doi.org/10.1080/00222348608248036Search in Google Scholar
Sumita, M., Asai, S., Miyadera, N., Jojima, E. and Miyasaka, K., “Electrical Conductivity of Carbon Black Filled Ethylene-Vinyl Acetate Copolymer as a Function of Vinyl Acetate Content”, Colloid Polym. Sci., 264, 212–217 (1986b) DOI: http://dx.doi.org/10.1007/BF01414955Search in Google Scholar
Sumita, M., Sakata, K., Asai, S., Miyasaka, K. and Nakagawa, H., “Dispersion of Fillers and the Electrical Conductivity of Polymer Blends Filled with Carbon Black”, Polymer Bulletin, 25, 265–271 (1991) DOI: http://dx.doi.org/10.1007/BF00310802Search in Google Scholar
Sumita, M., Sakata, K., Hayakawa, Y., Asai, S., Miyasaka, K. and Tanemura, M., “Double Percolation Effect on the Electrical Conductivity of Conductive Particles Filled Polymer Blends”, Colloid Polym. Sci.270, 134–139 (1992) DOI: http://dx.doi.org/10.1007/BF00652179Search in Google Scholar
Sung, Y. T., Han, M. S., Song, K. H., Jung, J. W., Lee, H. S., Kum, C. K., Joo, J. and Kim, W. N., “Rheological and Electrical Properties of Polycarbonate/Multi-Walled Carbon Nanotube Composites”, Polymer, 47, 4434–4439 (2006) DOI: http://dx.doi.org/10.1016/j.polymer.2006.04.008Search in Google Scholar
Tchoudakov, R., Breuer, O., Narkis, M. and Siegmann, A., “Conductive Polymer Blends with Low Carbon Black Loading: High Impact Polystyrene/Thermoplastic Elastomer (Styrene-Isoprene-Styrene)”, Polym. Eng. Sci., 37, 1928–1935 (1997) DOI: http://dx.doi.org/10.1002/pen.11843Search in Google Scholar
Tjong, S. C., Liang, G. D. and Bao, S. P., “Electrical Properties of Low Density Polyethylene/ZNO Nanocomposites: The Effect of Thermal Treatments”, J. Appl. Polym. Sci., 102, 1436–1444 (2006), DOI 10.1002/app.24294 DOI: http://dx.doi.org/10.1002/app.24294Search in Google Scholar
Tjong, S. C., Liang, G. D. and Bao, S. P., “Effects of Crystallization on Dispersion of Carbon Nanofibers and Electrical Properties of Polymer Nanocomposites”, Polym. Eng. Sci., 48, 177–183 (2008) DOI: http://dx.doi.org/10.1002/pen.20949Search in Google Scholar
Ward, I. M., Coates, P. D. and Dumoulin, M. M., (Eds.): Solid Phase Processing of Polymers, Hanser, Munich (2000) DOI: http://dx.doi.org/10.3139/9783446401846Search in Google Scholar
Wu, M., Shaw, L., “Electrical and Mechanical Behaviors of Carbon Nanotube-Filled Polymer Blends”, J. Appl. Polym. Sci., 99, 477–488 (2006) DOI: http://dx.doi.org/10.1002/app.22255Search in Google Scholar
Wu, S., “Calculation of Interfacial Tension in Polymer Systems”, J. Polym. Sci.: Part C, 34, 19–30 (1971) DOI: http://dx.doi.org/10.1002/polc.5070340105Search in Google Scholar
Wu, S., “Interfacial and Surface Tensions of Polymers”, J. Macromol. XI.-Revs. Macromol. Chem., C10, 1–73 (1974) DOI: http://dx.doi.org/10.1080/15321797408080004Search in Google Scholar
Wu, S.: Polymer Interface and Adhesion, 1st Edition, Marcel Dekker Publisher, New York (1982)Search in Google Scholar
Zeng, J., Saltysiak, B., Johnson, W. S., Schilraldi, D. A. and Kumar, S., “Processing and Properties of Poly(methyl methacrylate)/Carbon Nanofiber Composites”, Composites Part B, 35, 173–178 (2004) DOI: http://dx.doi.org/10.1016/j.compositesb.2003.08.009Search in Google Scholar
Zhao, Q., Wagner, H. D., “Raman Spectroscopy of Carbon-Nanotube-Based Composites”, Philos. Transact. A: Math. Phys. Eng. Sci., 362, 2407–2424 (2004) PMid:15482985; DOI: http://dx.doi.org/10.1098/rsta.2004.1447Search in Google Scholar PubMed
Zhou, P., Yu, W., Zhou, C., Liu, F., Hou, L. and Wang, J., “Morphology and Electrical Properties of Carbon Black Filled LLDPE/EMA Composites”, J. Appl. Polym. Sci., 103, 487–492 (2007) DOI: http://dx.doi.org/10.1002/app.25020Search in Google Scholar
© 2014, Carl Hanser Verlag, Munich
