Abstract
The aim of this study is to investigate the AZ31 alloy powder production and characterization processes experimentally using the gas atomization method. For this purpose, firstly, the design and production of gas atomization units were done at Karabük University Faculty of Technology Department of Manufacturing Engineering. In this gas atomization unit, the manufacturability of AZ31 powder from magnesium alloys was investigated by the gas atomization method which is one of the production methods by powder metallurgy. The parameters and the literature used in the production of materials similar to the AZ31 alloy are taken into account as producibility parameters. In the gas atomization method, parameters such as nozzle diameter, gas pressure, and temperature must be controlled in order to produce the desired properties in metal powder production. The diameter of the nozzle is crucial because it affects the gas pressure and temperature, the size of the powder, and the shape of the powders. Experimental studies were carried out using 3 different temperatures (790, 820, and 850°C), 4 different nozzle diameters (2, 3, 4, and 5 mm) and 4 different gas pressures (5, 15, 25, and 35 bar). In the molten metal atomization process and in the process of forming a protective gas atmosphere, argon gas was preferred. Scanning electron microscopy (SEM) was used to determine the shape of the AZ31 powders produced, XRD, XRF, and SEM-EDX analyses were used to determine the phases in the internals of the produced powders and percentages of these phases. Laser measurement devices were used for powder size analysis and hardness tests were performed to determine the mechanical properties of the produced powders. The powders produced were pressed into masses at 4 different pressing pressures (300, 400, 500, and 600 MPa). The best sinterability values of the bulked powders and sintering process were performed at 3 different temperatures (500, 550, and 600°C). Density measurements were made after pressing and sintering the powders. As a result of the experimental studies, it was found that the powder size decreased with the increase of the gas pressure but the nozzle diameter, and the powder shape changed to the dripping and the spherical in the ligament and complex form. It has been observed that the temperature has no significant effect on the powder size and shape.
Similar content being viewed by others
REFERENCES
Mordike, B.L. and Ebert, T., Magnesium properties applications potential, Mater. Sci. Eng., A, 2001, vol. 302, pp. 37–45.
Benedyk, J.J., Magnesium challenges aluminum dominance as the light metal of choice in automotive markets, Light Met. Age, 2004, vol. 62, no. 8, p. 5.
ASM Metals Handbook, vol. 14: Forming and Forging, West Conshohocken, PA: American Society for Testing and Materials, 1988, pp. 791–804.
Li, Y., and Zhang, Y., Light-weight and flexible high-entropy alloys, in High Entropy Alloys, Intechopen, 2019.
Niu, Y., Song, Z., Le, Q., Hou, J., and Ning, F., Excellent mechanical properties obtained by low temperature extrusion based on Mg–2Zn–1Al–0.2Mn–0.2Ca–0.2Gd alloy, J. Alloys Compd., 2019. https://doi.org/10.1016/j.jallcom.2019.05.297
Rajan, A.V., Sundaram, C.M., and Rajesh, A.V., Mechanical and morphological investigation of bio-degradable magnesium AZ31 alloy for an orthopedic application, Mater. Today: Proc., 2019; Rajan, A.V., Sundaram, C.M., and Rajesh, A.V., Mechanical and morphological investigation of bio-degradable magnesium AZ31 alloy for an orthopedic application, Mater. Today: Proc., 2020, vol. 21, pp. 272–277.
Fredrich, H. and Schumann, S., Research for a new age of magnesium in the automotive industry, J. Mater. Process. Technol., 2001, vol. 117, pp. 276–280
Furuya, H., Kogiso, N., Matunaga, S., and Senda, K., Applications of magnesium alloys for aerospace structure systems, Mater. Sci. Forum, 2001, vols. 350–351, pp. 341–351.
Froes, F.H., Eliezer, D., and Aghion, E., The science, technology, and applications of magnesium, J. Mater. Process. Technol., 1998, vol. 50, no. 9, pp. 30–34.
Vignesh, R.V., and Padmanaban, R., Forecasting tribological properties of wrought AZ91D magnesium alloy using soft computing model, Russ. J. Non-Ferrous Met., 2018, vol. 59, no. 2, pp. 135–141.
Gray, J. and Luan, B., Protective coatings on magnesium and its alloys-a critical review, J. Alloys Compd., 2002, vol. 336, nos. 1–2, pp. 88–113.
Kaya, R.A., Çavuşoğlu, H., Tanık, C., Kaya, A.A., Duygulu, Ö., Mutlu, Z., Zengin, E., and Aydın, Y., The effects of magnesium particles on posterolateral spinal fusion: an experimental in vivo study in a sheep model, J. Neurosurg.: Spine, 2007, vol. 6, pp. 141–149.
Duygulu, O., Kaya, R.A., Oktay, G., and Kaya, A.A., Investigation on the potential of magnesium alloy AZ31 as a bone implant, Mater. Sci. Forum, 2007, vols. 546–549, pp. 421–424.
Duygulu, O., Kaya, R.A., Oktay, G., Berk, C., and Kaya, A.A., Can magnesium alloys be used as implants?- SEM examinations from an in vivo study, Proc. 16th Int. Microscopy Conference, Sapporo, 2006.
Kaya, A.A., Future of magnesium: applications in transportation and bone surgery, Proc. 10th Int. Symposium on Advanced Materials (ISAM-2007), Islamabad, 2007.
Kaya, A.A., Kaya, R.A., Witte, F., and Duygulu, Ö., Useful corrosion- potential of magnesium alloys as implants, Proc. Int. Corrosion Engineering Conference, Seoul, 2007.
Lagutkin, S., Achelis, L., Sheikhaliev, S., Uhlenwinkel, V., and Srivastava, V., Atomization process for metal powder, Mater. Sci. Eng., A, 2004, vol. 383, no. 1, pp. 1–6.
Ünal, R., Gaz atomizasyonu ile metal tozu üretimi değişkenlerinin araştırılması, Yüksek Lisans Tezi, Ankara: Gazi Üniv., 1995.
Akkaş, M., Çetin, T., and Boz, M., The effect of gas pressure on powder size and morphology in the production of AZ91 powder by gas atomization method, Arch. Metall. Mater., 2018, vol. 63, no. 4, pp. 1587–1594.
Akkaş, M. and Boz, M., Investigation of the compressibility and sinterabilty of AZ91 powder production and particle production by gas atomization method, J. Magnesium Alloys, 2019, vol. 7, no. 3, pp. 400–413.
Uslan, İ. and Küçükarslan, S., Kalay tozu üretimine gaz atomizasyonu parametrelerinin etkisinin incelenmesi, Gazi Üniv. Mühendislik Mim.Fak. Derg., 2010, vol. 25, no. 1, pp. 1–8.
Clyne, T.W., Ricks, R.A., and Goodhew, P.J., The production of rapidly - solidified aluminium powder by ultrasonic gas atomization. Part I: Heat and fluid flow, Int. J. Rapid Solidif., 1984, vol. 1, pp. 59–80.
Daloz, D. and Michot, G., Influence of the consolidation step on the mechanical properties of rapidly solidified Mg–Al–Zn alloys, Int. J. Rapid Solidif., 1996, vol. 9, pp. 289–304.
Rajan, T.P.D., Jayakumar, E., and Pai, B.C., Developments in solidification processing of functionally graded aluminium alloys and composites by centrifugal casting technique, Trans. Indian Inst. Met., 2012, vol. 65, no. 6, pp. 531–537.
Jafarzadeh, A., Ahmadi, T., Dehaghani, M.T., and Mohemi, K., Synthesis, corrosion and bioactivity evaluation of gelatin/silicon and magnesium Co-doped fluorapatite nanocomposite coating applied on AZ31 Mg alloy, Russ. J. Non-Ferrous Met., 2018, vol. 59, no. 4, pp. 458–464.
Çetin, T., Akkaş, M., and Boz, M., Investigation of the effect of gas pressure on powder characterization of AM60 magnesium alloy powder produced by gas atomization method, J. Fac. Eng. Archit. Gazi Univ., 2020, vol. 35, no. 2, pp. 967–977.
Hu, H.J., Fan, J.Z., Zhai, Z.Y., Wang, H., Li, Y.Y., and Gong, X.B., Physical fields evolution and microstructures for compound extrusion of AZ31 magnesium alloy, Russ. J. Non-Ferrous Met., 2014, vol. 55, no. 3, pp. 254–262.
Author information
Authors and Affiliations
Corresponding authors
Ethics declarations
The authors declare to have no conflict of interest.
About this article
Cite this article
Em Akra, K.M., Akkaş, M., Boz, M. et al. The Production of AZ31 Alloys by Gas Atomization Method and Its Characteristics. Russ. J. Non-ferrous Metals 61, 332–345 (2020). https://doi.org/10.3103/S1067821220030074
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.3103/S1067821220030074