Abstract
The ceramic fibers VK-60, ABK, and VK-80 produced by steam blowing and nozzle dissemination methods have been investigated for the effect of nonfibrous material content, pressure, and temperature on the thermal conductivity at ambient and higher temperatures. It was noticed that with an increase in the aluminum content of the ceramic fibers the thermal conductivity of the material decreased while the insulation properties improved. The VK-80 fibers have the lowest and the VK-60 fibers the highest value of thermal conductivity at ambient temperature. At ambient temperature, the value of thermal conductivity increased with an increase in pressure for all analyzed fibers. ABK fibers showed the least increase and VK-80 registered an increase of about 10% in the values of thermal conductivity for pressures ranging from 0.6 to 6.6 kN/2. However, beyond a pressure of 6.6 kN/m2, the thermal conductivity of all samples increased. To assess the insulation properties of investigated fibers, the thermal conductivity was measured at different temperatures up to 800 °C. From the obtained results, it was concluded that all three types of fibers have a good potential for future applications, showing good performance in the investigated temperature range.
Similar content being viewed by others
References
“NPO Stekloplastic. The Pilot Plan of Kaolin Fiber Production,” Technical Report, Russia, 1971 (in Russian).
“NPO Stekloplastic Solution Production Methods of Oxide Ceramic Fibers,” Analytical Survey, Russia (in Russian).
“Reference Materials for Isolation Measurements Comparisons, Thermal Transmission,” ASTM Subcommittee C-16.300, ASTM, Philadelphia, PA.
Measurements of Insulation, ASTM STP, R.P. Tye, ed., ASTM, Philadelphia, PA, 1978.
E.P. Incropera and D.P. deWitt: Fundamentals of Heat and Mass Transfer, John Wiley & Sons, Inc., New York, NY, 1985, p. 90.
Handbook of Heat Transfer, W.M. Rohsenow and J.P. Hartnett, eds., McGraw-Hill, New York, NY, 1973.
Transient Analysis Used to Study Thermal Radiation Effects in Single and Composite Semitransparent Layers, NASA Lewis Research Center, 1996.
L.C. Burmeister: Convective Heat Transfer, John Wiley & Sons, Inc., New York, NY, 1993.
T. Log and S.E. Gustafsson: Fire Mater., 1994, vol. 19, p. 43.
B.M. Suleiman, E. Karawacki, and S.E. Gustafsson: High Temp.-High Pressure, 1993, vol. 25, p. 205.
Silas E. Gustafsson: Rev. Sci. Instrum., 1991, vol. 62, p. 797.
S.E. Gustaffsson, E. Karawachi, and M.A. Chohan: J. Phys. D, 1986, vol. 19, p. 259.
Aslanaova “Development of Continuous Technique for Kaolin Fibner and Kaolin Baed Products Production,” Technological Report, 1974 (in Russian).
M.C.I. Siu: Fibrous Glass Board as a Standard Reference Material for Thermal Resistance Measurement Systems, ASTM STP 718, D.L. McErloy and R.P. Tye, eds., ASTM, Philadelphia, PA, 1980.
“Catalog of Construction Isolation Materials,” Company Catalog, ISOVER, 1996.
Author information
Authors and Affiliations
Rights and permissions
About this article
Cite this article
Gumen, V., Illyas, B., Maqsood, A. et al. High-temperature thermal conductivity of ceramic fibers. J. of Materi Eng and Perform 10, 475–478 (2001). https://doi.org/10.1361/105994901770344917
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1361/105994901770344917