Skip to main content

Fuel value indices of selected woodfuel species used in Masindi and Nebbi districts of Uganda

Abstract

Background

Biomass currently meets more than 97% of the total energy requirements in Uganda. However, contrary to this heavy reliance on biomass, there is paucity of information regarding the fuel value indices (FVIs) of woodfuel species used in different locations of the country such as Masindi and Nebbi districts. This study therefore sought to identify ten woodfuel species commonly used by the communities in these two districts and examine their FVIs from basic properties, namely; moisture content, density and gross calorific value.

Methods

A semi-structured interview using a checklist of guiding questionnaire was conducted to generate a woodfuel species list. The familiarity index (FI) was calculated for each species and then used to rank ten commonly used species for further analysis. The moisture content, density and gross calorific value of the selected species were determined in triplicate. The FVI of each species was then determined from these basic properties. One-way ANOVA, Pearson product moment correlation, and Spearman rank correlation coefficient analyses were performed in SPSS ver.16.0 to examine the variation and relationship of variables.

Results

Ten woodfuel species belonging to seven families and eight genera were identified as commonly used species. Combretum collinum was mentioned by every respondent as a suitable woodfuel species. A significant variation in moisture content and density was recorded among the species (F ( df = 9) = 92.927, p = 0.0001) unlike in gross calorific value (F ( df = 9) = 1.400, p = 0.253). There was a positive correlation between density and gross calorific value (r = 0.895, n = 30, p = 0.0001) and a negative correlation between moisture content and gross calorific value (r = −0.518, n = 30, p = 0.003). The FVIs obtained ranged from 1.10 in Ficus natalensis to 13.09 in Albizia grandibracteata. There was also a positive relationship (rho = 0.62) between FVIs and FIs using Pearson rank correlation coefficient.

Conclusions

Moisture content and density are important properties in the selection of woodfuel species than gross calorific value. On the proposition of the FVIs, A. grandibracteata is a suitable woodfuel species than F. natalensis. These findings fit well into the ongoing efforts by Government and Civil Society Organizations to encourage woodlot management to ensure the sustainability of woodfuel in the country.

Background

Woodfuel is the largest energy source for the world’s population in developing countries and the demand is likely to continue [1,2]. The use of woodfuel is both an ancient and modern tradition that is not likely to change in the next decades [3]. Woodfuel is particularly significant to the poor and rural households [3,4]. The greatest portion of woodfuel is derived from natural forests, and the dwindling forest cover has made its availability a matter of critical concern in most developing countries [5,6]. The limited availability and high cost of alternative energy resources in Africa continue to make firewood and charcoal the major energy resource [7]. The heavy reliance on woodfuel has escalated the woodfuel demand leading to forest cover decline and inevitable woodfuel shortages in many African countries [8-10].

In Uganda, biomass is the most significant source of energy with a wide range of applications from domestic use such as heating, cooking, and lighting to small-scale industrial use in bakeries, tea processing, tobacco curing, lime and brick making, fish smoking, jaggeries, and distilleries [8,9,11]. It currently accounts for more than 97% the country’s energy supplies [8,12]. The daily per capita consumption rate is estimated to be 4 kg [11]. In the urban areas, people use charcoal more than firewood because the former has lower transport costs per unit energy and higher energy content per ton [13]. However, it is produced inefficiently thus contributing to the scarcity of bioenergy resources.

The relentless demand for biomass energy in Uganda has been attributed to the increasing population, growing industrial sector, as well as increased rate of urbanization [14]. This shows that socioeconomic factors are largely responsible for the dependence on biomass energy resources which are available at low (or even zero) cost while commercial fuels such as liquefied petroleum gas, kerosene, and diesel are often beyond the acquisitive power of most poor people [15]. The socioeconomic characteristics of local communities in Uganda such as age, gender, wealth, education, heterogeneity of the population, household size, land holding, and distance from the forest are believed to greatly influence the level of dependence on firewood [16].

The contribution of natural forests and woodlands to biomass energy supplies in Uganda has been recognized [9,17]. However, assessment of woodfuel FVIs from basic properties remains inadequately addressed. This information is important in aiding the identification of high fuel potential woodfuel species to enhance existing woodfuel stocks so that the low-cost energy source is maintained [10]. There is evidence that the improvement of existing stocks is cheaper than establishment of new plantations or woodlots [18]. Indeed, the management of landscapes with the aim of producing woodfuel or maintaining existing stocks requires that woodfuel species with qualities acceptable to rural communities are identified [19]. Besides providing woodfuel, the management of indigenous woodlands is believed to be more ecologically sound and offers better chances for the conservation of biodiversity [9]. It is with this background that this study sought to answer the questions: (i) Which woodfuel species are commonly used by the communities in Masindi and Nebbi districts? (ii) What are their FVIs computed from basic properties (gross calorific value (GCV), density (D), and moisture content (MC))?. This information is vital in prioritizing high fuel-potential tree species for utilization, management, and improvement to ensure a steady supply of woodfuel. This study therefore fits well into the ongoing Government and Civil Society campaigns to maintain woodlots so as to ensure a balance between supply and demand of woodfuel in the country.

Methods

Study area

This study was conducted in Masindi and Nebbi districts of Uganda. Nebbi district is located in the north western region of Uganda between 2° 20′ and 2° 40′ N and 31° 0′0 and 31°.20′ E. It lies at an altitude of 945 to 1,219 m above sea level. It is bordered by the Democratic Republic of Congo in the East. Meanwhile, Masindi district is located in western Uganda and lies between 1° 22′ and 2° 20′N and 31° 22′ and 32° 23′E and altitude in the range of 621 to 1,158 m above sea level. These two districts were selected based on their current extensive savannah biomass stocks that supply the major neighboring urban areas.

Selection of informants

A multistage sampling approach was used to select the informants. In this technique, two sub-counties from Masindi and Nebbi districts (Pakanyi and Nebbi, respectively) were randomly selected; one parish was selected randomly from each sub-county, and four villages were chosen from each parish. A systematic random sampling technique was used to select 10 respondents in each village for the interview totaling to 80. A semi-structured questionnaire was administered to women and girls as the key informants in order to elicit responses on trees used for woodfuel purposes. The free listing technique was applied whereby the respondents were asked to mention any tree that comes to their mind until they could not mention any more species. From the responses, the FI was calculated for each species according to [20], and the ten species with the highest FI (Table 1) were chosen for basic property analysis.

Table 1 Ten commonly used woodfuel species

Wood sample collection and preparation

Wood samples measuring 30 cm in length and 2.5-cm diameter were collected for each of the ten woodfuel species shown in Table 1. These samples were prepared according to [15] whereby each was sub-divided into triplicates of length 10 cm, marked and weighed immediately in the field, and brought for analysis in the laboratory. The MC, D, and GCV were determined as described in the subsequent sections.

Moisture content (MC)

The triplicate samples were dried in an electric oven at 100°C until they attained a constant weight. The MC was then determined on dry weight basis according to Equation 1 [21]:

$$ \mathrm{M}\mathrm{C}=\frac{Ww-Wo}{Wo}\times 100\% $$
(1)

where Ww = wet weight and Wo = oven-dry weight.

Density (D)

This was determined as a ratio between oven-dry weight (g) and volume (cm3) using Equation 3. The procedure followed the technique described in [22] whereby wood volume is first determined by immersing the samples in water for 5 days (120 h) to achieve total saturation, allowed to drain for 5 min, and their diameters measured using a vernier caliper. The volume was calculated using Equation 2:

$$ \mathrm{Volume}=\frac{\pi \times {D}^2\times L}{4} $$
(2)

where D = average diameter and L = length of the sample.

The samples were again dried at 100°C until attaining a constant weight. The D was then calculated according to Equation 3:

$$ \mathrm{Density}=\frac{\mathrm{DW}}{\mathrm{SV}} $$
(3)

where DW = dry weight (g) and SV = sample volume (cm3)

Gross calorific value

The GCV of the wood samples was determined using a Gallenkamp autobomb calorimeter (SG96/02/536, Gallenkamp and Company Ltd, London, UK). The method is based on combustion in the ‘bomb’ chamber. When the sample is burned, the resulting heat is measured by the increase in the temperature of water surrounding the bomb. In this study, 1g of wood sample was pelleted using a briquette press and weighed in a crucible. The pellet was then connected to the firing wire fitted between the electrodes with the aid of a cotton thread. The circuit was tested and the bomb was filled with oxygen to a pressure of 3,000 Pa (30 bar). The calorimeter vessel was filled with water (total weight 3 kg) at 21°C to 23°C; the prepared bomb was placed inside the calorimeter vessel, and then the calorimeter vessel was placed into the water jacket. The machine was switched on and left for a while (10 to 15 min) to warm up. The initial temperature of the water was recorded before firing and after 10 to 15 minutes, the final temperature reached was recorded. Benzoic acid was used as a standard. The GCV was then calculated using Equation 4:

$$ \mathrm{G}\mathrm{C}\mathrm{V}\kern0.5em =\left[\left(FT- IT\right)\kern0.5em \times \kern0.5em 10\cdot 82\right]\kern0.5em -\kern0.5em 0.086/\left(\mathrm{weight}\kern0.5em \mathrm{of}\kern0.5em \mathrm{sample}\right) $$
(4)

where 10.82 = heat capacity of the calorimeter in kJ/K, 0.086 = combined energy value of nickel wire and cotton in kJ/g, FT = final temperature, and IT = initial temperature

Fuel value index (FVI)

This was calculated by considering D and GCVs as positive characters and MC as the negative character using Equation 5 [19]:

$$ \mathrm{F}\mathrm{V}\mathrm{I}=\frac{\mathrm{Gross}\kern0.5em \mathrm{calorific}\kern0.5em \mathrm{value}\kern0.5em \left(\mathrm{K}\mathrm{J}/\mathrm{g}\right)\kern0.5em \mathrm{Density}\kern0.5em \left(\mathrm{g}/\mathrm{cm}\right)}{\mathrm{Moisture}\kern0.5em \mathrm{content}\left(\%\right)} $$
(5)

Data analysis

SPSS ver. 16.0 was used to analyze the results. The following tests were carried out: (i) one-way ANOVA on the variability of MC, D, and GCV, (ii) Pearson product correlation coefficient on the relationship between D and GCV and MC and GCV, and (iii) Pearson rank correlation coefficient on the relationship between FVIs and FIs.

Results and discussion

Preferred woodfuel species

Table 1 shows the list of ten commonly used woodfuel species with their FIs. The species are distributed among eight genera and seven families. The family Mimosaceae has three species; Combretaceae has two while the rest have one species each. The genus Albizia and Combretum have two species each and the others have one. Combretum collinum (FI = 100) was mentioned by all respondents as a desirable woodfuel species. This is attributed to its availability in the surrounding environment and apparent possession of desirable woodfuel properties which has been reported elsewhere [10,13,23,24]. Tamarindus indica was least mentioned as woodfuel because the benefits from its fruits are seen to outweigh those resulting from woodfuel use.

Woodfuel basic properties and FVIs

Moisture content

There was a significant variation in the MC among the species at p < 0.05 level (F ( df = 9) = 92.927, p = 0.0001), and the effect size calculated using eta squared was 0.976. The MC ranged from 36.18% in A. grandibracteata to 69.41% in Ficus natalensis (Table 2). Assessment of the Pearson product moment correlation coefficient between MC and GCV showed a negative correlation (r = −0.518, n = 30, p = 0.003) with 26.83% coefficient of determination. This confers with the widely held acknowledgement that MC adversely affects the calorific value of the wood [10,25]. However, a one-to-one examination showed that F. natalensis deviates from this widely held inference conferring with the trend that [6] also reported. Water in green tissues exists primarily in the form of free water filling the capillaries and as water of constitution (e.g., water absorbed in lignocellulose) [6]. The variation in the number and size of wood capillaries and water of constitution is a key determinant of MC variation across species [26]. This therefore implies that species with high MC have a large number and size of wood capillaries and consequently water of constitution than those with low MC.

Table 2 Basic properties and FVIs of woodfuel species used in Masindi and Nebbi districts

Density

There was a significant variation at p < 0.05 level (F (df = 9) = 11.528, p = 0.0001) in the D of woodfuel species and the effect size was 0.84 determined using eta squared. The D values ranged from 0.23 g/cm3 in F. natalensis to 0.64 g/cm3 in A. grandibracteata (Table 2). A strong positive correlation between D and GVC was obtained using Pearson product moment coefficient (r = 0.895, n = 30, p = 0.0001) with a coefficient of determination of 80%. This trend was also reported by [27,28]. The D values obtained in this study are, however, lower than those reported in [9] due to the use of small-dimension samples in this study which are less dense than the whole branches used in the previous study (Table 3). Wood density describes the proportion of a stem that is tissue and cell walls (xylem conduit walls) and space within cell walls (xylem conduit apertures) [29]. Woodfuel species with high D have high fiber tissue per unit volume and thick fiber walls than those with low D [29], more carbon and energy content per unit volume [30], and produce long-lasting embers [19,31]. However, like the findings of [32], this investigation also found that F. natalensis with a low D (Table 2) has a high GCV. Although it was not investigated during study, high GCVs have been attributed to high concentrations of extractives and lignins in wood [31] and is therefore a plausible explanation for this exception.

Table 3 Comparison between current and [9] results

Gross calorific value

The variation in GCVs of woodfuel species was insignificant at p < 0.05 level (F (df = 9) = 1.400, p = 0.253) which is also reported by [25]. The values obtained ranged from 20.05 KJ/g in A. grandibracteata to 29.46 KJ/g in F. natalensis (Table 2). Woodfuel species with high GCVs have high concentrations of extractives and lignins in wood while a predominance of sugar units such as cellulose and hemicellulose leads to lower GCVs [31].

Fuel value index

The FVIs ranged from 1.10 in F. natalensis to 13.09 in A. grandibracteata (Table 2). There was a positive but insignificant relationship between FVIs and FIs (r = 0.62, n = 10, p = 0.056). This positive relationship between FVIs and FIs indicates that local preference is partly informed by physical (basic) properties of the wood. The values generated here are lower than those obtained by the authors in [9] who considered D and MC only (Table 3). The variation in the geographical location of the studies is also a plausible source of this difference. The FVI is an insightful parameter for screening woodfuel species [10], and it can be concluded that A. grandibracteata with the highest FVI possesses better woodfuel properties. However, authors in [19] assert that rural people are very discerning about woodfuel requirements and therefore socially acceptable features also need to be considered to generate woodfuel species checklist in a given locality.

Conclusions

The woodfuel species used in Masindi and Nebbi districts show significant variations in MC and D. These two variables are therefore more important in assessing woodfuel species. The results further emphasize that a single basic property is not sufficient to justify selection of the most suitable woodfuel species thereby conferring with authors in [10]. On the proposition of the FVIs, A. grandibracteata is a more suitable woodfuel species than F. natalensis. This study therefore lays an important premise for selection of high fuel potential woodfuel species for possible inclusion into reforestation, afforestation, and agroforestry initiatives currently encouraged by the Government and Civil Society Organizations to address woodfuel shortage in Uganda generally. However, before such species prioritization is done, it is recommended that socially defined features that shape local peoples’ perception of acceptable woodfuel species need to be considered [6,19] which was not undertaken in this study. This will lead to the generation of woodfuel species checklist that is socially acceptable and with high fuel potential in a given area.

References

  1. Scurlock JM, Hall DO (1990) The contribution of biomass to global energy use. Biomass 21:75–81

    Article  Google Scholar 

  2. Deka D, Saika P, Konwer D (2007) Ranking of woodfuel species by fuel value index. Energy Sources Part A 29:1499–506

    Article  Google Scholar 

  3. Matthews E (2000) Undying flame: the continuing demand for wood as fuel. Extract from pilot analysis of global ecosystems: forest ecosystems. Earth trends 2001 World Resources Institute

  4. Hall DO (1994) Introduction, summary and conclusions. In: Hall DO, Mao YS (eds) Biomass energy and coal in Africa. Zed Books and AFREPREN, London, pp 1–16

    Google Scholar 

  5. Delali BKD, Witkowski ETF, Shackleton MC (2004) The fuelwood crisis in southern Africa—relating fuelwood use to livelihoods in a rural village. Geo J 60:123–33

    Google Scholar 

  6. Shanavas A, Kumar BM (2003) Woodfuel characteristics of tree species in home gardens of Kerala, India. Agroforestry Syst 58:11–24

    Article  Google Scholar 

  7. Pak SL (2005) Climate change and Africa. Cambridge University Press, Cambridge, p 412

    Google Scholar 

  8. NEMA (2008) State of the environment report for Uganda. National Environment Management Authority, Kampala, Uganda

    Google Scholar 

  9. Tabuti JRS, Dhillion SS, Lye KA (2003) Firewood use in Bulamogi County, Uganda: species selection, harvesting and consumption patterns. Biomass Bioenergy 25(6):581–96

    Article  Google Scholar 

  10. Abbot PG, Lowore JD (1999) Characteristics and management potential of some indigenous firewood species in Malawi. For Ecol Manage 11:111–21

    Article  Google Scholar 

  11. Forest department (2003) National biomass study technical report of 1996–2002. Ministry of Water and Environment. Kampala, Uganda

    Google Scholar 

  12. MEMD (2006) Renewable energy policy for Uganda. Ministry of Energy and Mineral Development. Kampala, Uganda

    Google Scholar 

  13. Agea JG, Kirangwa D, Waiswa D, Okia CA (2010) Household firewood consumption and its dynamics in Kalisizo sub-county, central Uganda. Ethnobotanical Leaflets 14:841–55

    Google Scholar 

  14. UBOS (2010) Statistical abstract. Uganda Bureau of Statistics (UBOS), Kampala

    Google Scholar 

  15. Bhatt BP, Tomar JMS (2002) Firewood properties of some Indian mountain tree and shrub species. Biomass Bioenergy 23:257–60

    Article  Google Scholar 

  16. Turiho-habwe GP (1995) A socio-economic analysis of communal resource use: the case of non-gazetted forests of western Uganda. Makerere University, Kampala, MSc Thesis, 108 pp

    Google Scholar 

  17. Katende AB, Birnie A, Tengnas B (1995) Useful trees and shrubs for Uganda: identification, propagation and management for agricultural and pastoral communities. Regional Soil Conservation Unit (RSCU), Nairobi, Kenya

    Google Scholar 

  18. Harrison P (1987) The greening of Africa: breaking through in the battle for land and food. Paladin, London, 371 pp

    Google Scholar 

  19. Abbot PG, Lowore J, Khofi C, Werren M (1997) Defining firewood quality: a comparison of quantitative and rapid appraisal techniques to evaluate firewood species from a southern African savanna. Biomass Bioenergy 12:429–37

    Article  Google Scholar 

  20. Tabuti JRS (2007) The status of non-cultivated food plants in Balumogi County, Uganda. African J Ecol 45(1):99–101

    Google Scholar 

  21. Valter F, Antonini E, Bergoni LZ (2008) Wood fuels handbook: production, quality requirements and trading. Italian Agroforestry Energy Association, p 19. Agripolis, Italy.

  22. Alves Ramos M, de Medeiros PM, de Almeida ALS, Feliciano ALP, de Albuquerque UP (2008) Can wood quality justify local preferences for firewood in an area of Caatinga (dryland) vegetation? Biomass Bioenergy 32:503–9

    Article  Google Scholar 

  23. Tietema T, Ditlhogo M, Tibone C, Mathalaza N (1991) Characteristics of eight firewood species of Botswana. Biomass Bioenergy 1:41–56

    Article  Google Scholar 

  24. Shackleton CM, Griffin NJ, Banks DI, Mavrandons JM, Shackleton SE (1994) Community structure and species composition along a distribution gradient in a communally managed South African savanna. Vegetation 115:157–67

    Google Scholar 

  25. Kataki R, Konwer D (2002) Woodfuel characteristics of indigenous tree species of North East India. Biomass Bioenergy 22:433–7

    Article  Google Scholar 

  26. Skaar C (1988) Wood-water relations. Springer, Berlin, pp 20–33

    Book  Google Scholar 

  27. Bhatt BP, Todaria NP (1992) Woodfuel characteristics of some mountain species. Forest Ecol Manag 47:363–6

    Article  Google Scholar 

  28. Jain RK, Singh B (1999) Woodfuel characteristics of selected indigenous tree species from central India. Bioresour Technol 68(3):305–8

    Article  Google Scholar 

  29. Hakkila P (1984) Forest chips as fuel for heating plants in Finland Summary: forest seasoning of wood intended for fuel chips. Communications Insituti Fenniae 54 (4): 82, Finland.

  30. Shafizadeh F (1981) Basic principles of direct combustion. In: Sofer SS, Zabrosky OR (eds) Biomass conversion process for energy and fuels. Plenum, New York, pp 103–12

    Chapter  Google Scholar 

  31. Kataki R, Konwer D (2001) Woodfuel characteristics of some woody species of North East India. Biomass Bioenergy 20:17–23

    Article  Google Scholar 

  32. Singh B, Khanduja SD, Srivastava GS (1984) Qualitative analysis of some firewood shrubs. Biomass 5:317–20

    Article  Google Scholar 

Download references

Acknowledgements

The authors acknowledge the support by Makerere University Staff Development Program and DAAD In-Country Scholarship program for Uganda for SO. We thank Robert Nuwamanya, the laboratory technician at College of Agricultural and Environmental Sciences, Makerere University for his technical guidance in GCV determination. We also thank the communities of Masindi and Nebbi for willingly participating in our interviews.

Author information

Authors and Affiliations

Authors

Corresponding author

Correspondence to Samuel Ojelel.

Additional information

Competing interests

The authors declare that they have no competing interests.

Authors’ contributions

SO was responsible for data collection, laboratory experiments, analysis, and drafting of the manuscript. TO and SM were in charge of the study design, reviewing the manuscript draft, and overseeing the research. All the authors have therefore contributed substantially to this manuscript. All authors have read and approved the final manuscript.

Authors’ information

TO is a professor in the Department of Physics, Makerere University. He is also the chairman, Uganda National Energy Development Organization (UNEDO); member of African Energy Policy Research Network (AFREPREN); group leader, Solar Energy Research Group, Physics Department, Makerere University; Member of the International Energy Foundation (IEA) and a member of the Scientific and Technical Advisory Panel (STAP) of the Global Environment Facility (GEF). SM (PhD) is a lecturer in the Department of Biological Sciences of Makerere University. SO is a teaching assistant in the Department of Biological Sciences, Makerere University and also a post graduate student in the same Department.

Rights and permissions

Open Access This article is distributed under the terms of the Creative Commons Attribution 4.0 International License (https://creativecommons.org/licenses/by/4.0), which permits use, duplication, adaptation, distribution, and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons license, and indicate if changes were made.

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Ojelel, S., Otiti, T. & Mugisha, S. Fuel value indices of selected woodfuel species used in Masindi and Nebbi districts of Uganda. Energ Sustain Soc 5, 14 (2015). https://doi.org/10.1186/s13705-015-0043-y

Download citation

  • Received:

  • Accepted:

  • Published:

  • DOI: https://doi.org/10.1186/s13705-015-0043-y

Keywords