Abstract
We predict a giant field-like spin torque, , in spin-filter (SF) barrier tunnel junctions in sharp contrast to existing junctions based on nonmagnetic passive barriers. We demonstrate that has linear bias behavior, is independent of the SF thickness and has odd parity with respect to the SF’s exchange splitting. Thus, it can be selectively controlled via external bias or external magnetic field which gives rise to sign reversal of via magnetic field switching. The underlying mechanism is the interlayer exchange coupling between the noncollinear magnetizations of the SF and free ferromagnetic electrode via the nonmagnetic insulating (I) spacer giving rise to giant spin-dependent reflection at the SF/I interface. These findings suggest that the proposed field-like-spin-torque MRAM may provide promising dual functionalities for both ‘reading’ and ‘writing’ processes which require lower critical current densities and faster writing and reading speeds.
Similar content being viewed by others
Introduction
Recent discoveries in the ferromagnet/insulator/ferromagnet (FM/I/FM) magnetic tunnel junctions (MTJs) have demonstrated that the relative orientation of the two FM electrodes can be either altered by an external magnetic field, i.e. the tunneling magnetoresistance (TMR) effect1, or controlled by a spin-polarized current, i.e. the current-induced magnetization reversal via the spin transfer torque (STT) effect2,3. The spin-transfer, and field-like, , components of the STT originate from different components of the spin current accumulated at the FM/I interface4,5 and can be expressed in terms of the interplay of spin current densities6,7 and of the non-equilibrium interlayer exchange couplings8, respectively, solely in collinear configurations.
Usually, the writing process in magnetic random access memory (MRAM) bits is performed via the spin transfer torque, 9,10,11, which is much larger than the field-like component, , while the read-out operation is reliably performed via the TMR effect12. However, the magnetization switching requires high current densities and hence high power consumption, both of which are detrimental also to the TMR. Therefore, alternative writing and reading mechanisms for MTJs may provide a viable route towards switching energies per bit close to or smaller compared with CMOS (~1 fJ)13.
The insulator in conventional FM/I/FM MTJs plays only a passive role in the spin-polarized transport. The evolution beyond passive components has broadened the quest for multifunctional spintronic devices consisting of either ferroelectric14,15,16,17,18,19 or spin-filter (SF) barriers20,21,22,23. The latter exploits the separation of the barrier heights, φσ, of the two spin channels, 2Δ ≡ φ↑ − φ↓, which can be in turn tuned via an external magnetic field20,23. Early SF tunnel junction structures employed the europium chalcogenides (EuS, EuO, etc.) as a ferromagnetic barrier20,21,22,24. The limitation of low Curie temperatures for this family of compounds sparked intense research interest in perovskite- and spinel-structured ferrite and manganite compounds, such as NiFe2O425, CoFe2O426, NiMn2O427 and BiMnO328, which magnetically order at much higher temperatures. The large TMR values reported29 in NM/SF/FM MTJs, where NM denotes a nonmagnetic metal, result from the combination of the spin filter tunnel barrier and the ferromagnetic electrode. Furthermore, NM/SF/I/FM MTJs consisting of a thin nonmagnetic insulator spacer to effectively decouple the SF-barrier and the FM electrode exhibit large magnetoresistance30. In double SF tunnel junctions NM/SF/I/SF/NM proposed by Miao et al.31,32, the tunneling probabilities for spin-up and spin-down electrons are different because they depend exponentially on the spin-dependent barrier height. By toggling the magnetization of the two SF barriers between parallel and antiparallel configurations a high TMR value was achieved.
The objective of this work is to employ tight binding calculations and the non-equilibrium Green’s function formalism to study the effect of the SF-barrier magnetization on the bias behavior of both components of STT in noncollinear FM/I/SF/I/FM junctions. We predict a giant field-like spin torque component, , in contrast to conventional FM/I/FM junctions, which has linear bias dependence, is independent of the SF thickness and has sign reversal via magnetic field switching. The underlying mechanism is the interlayer exchange coupling between the noncollinear magnetizations of the SF and free ferromagnetic electrode via the nonmagnetic insulating spacer giving rise to giant spin-dependent reflection at SF/I interface. We demonstrate dual manipulation of via external magnetic field and external bias which provides a new avenue to achieve both ‘reading’ and ‘writing’ processes of nonvolatile field-like spin torque MRAM (FLST-MRAM), which may require lower critical current densities for magnetization switching than conventional STT-MRAM.
Results
We consider the Co/Al2O3/EuS/Al2O3/Co junction, shown schematically in Fig. 1, consisting of three layer I/SF/I barrier sandwiched between two semi-infinite FM electrodes. The two nonmagnetic insulators serve as spacer layers between the Co and the SF to prevent any direct exchange magnetic coupling and to ensure independent switching of the SF magnetization, MSF, or the magnetization of the right FM electrode, MR. The ferromagnetic ordering in europium chalcogenides originates from the localized moments of the Eu 4f-derived states which in turn causes a large exchange splitting, 2Δ, between the Eu-5d majority- and minority-derived conduction bands33. The direction of the in-plane magnetization MSF can be toggled along the ±z direction by an external magnetic field20,23 which induces in turn sign reversal of Δ.
The spin-transfer, and field-like, , components of the net spin torque per interfacial unit area, ?, on the right (free) FM are along the and the directions, respectively, shown in Fig. 1. Here, is the unit vector of the magnetization of the left (right) FM. These can be determined from the spin current density accumulation at the right I/FM interface7,
where is the 2 × 2 Keldysh Green’s function matrix in spin space, α′ and b are the first and last sites of the right FM electrode and the right I-barrier, respectively, shown in Fig. 1, σy(z) is the y (z)-component of the Pauli matrix vector, is the transverse wave vector and the energy integral is over occupied states.
Extending the non-equilibrium Keldysh formalism for the conventional FM/I/FM in the limit of thick barrier34,35 to the FM/I/SF/I/FM junction we find that the Green’s function matrix at the right I/FM interface can be written as
Here, , is the Keldysh Green’s function for the entire junction which is analogous to Eq. (9) in Ref. 34 for the FM/I/FM junction. However, the additional term, , arises from the spin-dependent reflection at the SF/I interface due to tunneling electrons from the right FM. The and are given by
and
Here, the subscripts refer to the sites in the various regions of the FM/I/SF/I/FM junction in Fig. 1, are the retarded and advanced surface Green’s function matrices of the isolated left (right) FM and fL(R) is the Fermi-Dirac distribution function of left (right) FM electrode. The Green’s functions, , and , of the isolated I-barrier are real and the Green’s function matrices, and , of the isolated SF-barrier are real and diagonal.
Assuming that the magnetizations of the left fixed ferromagnet, ML and the spin filter, MSF, are collinear and substituting Eqs. (3) and (4) in Eq. (1) we find that the STT componen.ts are
and
Note that the effect of SF dominates while is negligible for , because the Im[] has only nonzero off-diagonal matrix elements. Here, J↑(↓) is the non-equilibrium interlayer exchange coupling (NEIEC) between the spin-↑(↓) states of the left and right FMs in the parallel (PC) and anti-parallel (APC) configurations and is the spin current density along z for the PC and APC. These general expressions demonstrate that the bias dependence of noncollinear components of the STT can be decomposed as the interplay between (NEIECs) solely in the collinear magnetic configurations. This in turn allows the efficient calculation of the STT from collinear ab initio electronic structure calculations36,37. We would like to emphasize that the results of the calculations are general and do not depend whether the collinear magnetizations of the left fixed ferromagnet and the spin filter are out-of-plane or in-plane.
In Fig. 2 we present the bias dependence of and for the FM/I/SF/I/FM junction with Δ = 0.12 eV and NIL = NSF = NIR = 3. The solid curves and circles represent the STT values calculated from Eq. (1) and Eqs. (5) or (6), respectively, demonstrating the excellent agreement between these two computational schemes. We also show for comparison the STT components (dashed curves) for the conventional FM/I/FM junction with NI = 9, i.e., the same thickness of the I-barrier and Δ = 0.0 eV. Note the different scales in the left- and right-hand ordinates in Fig. 2(a). The most striking result is the giant values of in the SF-junction which is about four orders of magnitude higher than , in sharp contrast to conventional FM/I/FM junctions where . Furthermore, the SF renders the bias behavior of nearly linear in the low bias regime while in conventional FM/I/FM junctions is purely quadratic. On the other hand, the effect of the SF on the bias behavior of is small compared to that in the conventional junction with Δ = 0.0 eV, due to the fact of . This giant enhancement of the field-like torque may in turn lead to reduction of the critical current necessary for magnetization switching in the next-generation MRAMs. However, the resistance-area product (RA) (and hence the barrier thickness) in MTJs used for MRAM will also have an important role on the write energy per bit and the switching current density38.
In order to elucidate the underlying mechanism of the SF-induced enhancement of , we show in Fig. 3(a,b) the zero-bias energy-resolved contributions of the nonmagnetic insulator spacer, and of spin-filter, , respectively, to the net field-like spin torque, , in Eq. (5). is the energy-dependent integrand in Eq. (1) after integrating over the transverse wave vector, . For conventional FM/I/FM junction (Δ = 0) the spin-filter contribution, , vanishes identically and . On the other hand, for the FM/I/SF/I/FM junction (Δ ≠ 0) the important question is what is the relative size of and ? Interestingly, for the FM/I/SF/I/FM junction we find that the energy-resolved contribution, , from the nonmagnetic insulator spacer [red solid curve in Fig. 3(a)] is qualitatively similar to, , for a conventional FM/I/FM junction (Δ = 0) [dotted black curve in Fig. 3(a)]. In sharp contrast, the SF energy-resolved contribution, , [magenta curve in Fig. 3(b)], which is present solely in SF-based MTJ is five orders of magnitude larger than that of the non-magnetic insulator spacer, , [note the difference in scale in Fig. 3(a,b)]. The giant value of [magenta curve in Fig. 3(b)] arises from the additional term, , in Eq. (4) due to the spin dependent reflection at the SF/I interface which is associated solely with the interlayer exchange coupling (IEC) between the SF and the right (free) FM electrode. Namely, because is noncollinear with only the spin-polarized electrons from the right FM encounter the non-collinear exchange field of the SF-barrier, thus giving rise to giant spin accumulation at the right I/FM interface.
Fig. 3(c) displays the energy dependence of the four IECs in the PC and APC configurations, shown schematically in the inset, as well as at zero bias for the SF-based junction with Δ = 0.12 eV and NIL = NSF = NIR = 3. For both PC and APC we find that , which is induced primarily from the giant IEC between the noncollinear SF barrier and the right FM due to the spin-dependent reflection at the SF/I interface. It is interesting to note that because they represent the IEC of the majority band in the right FM with the majority and minority conduction bands of the SF barrier, respectively, shown in the inset of Fig. 3(c).
Discussion
We first examine the effect of barrier thickness on both spin torque components for SF-based junctions. In Fig. 4 we show (blue curves), (red curves) and the ratio (black curves) on a logarithmic scale as a function of the number of atomic layers in the (a) left I-barrier (NIL), (b) SF-barrier (NSF) and (c) right I-barrier (NIR) under 0.2 V external bias. Interestingly, similar to conventional FM/I/FM junctions, decays exponentially as the number of layers in the insulating and SF barriers increases with the same decay rate. In sharp contrast, the field-like component, , exhibits a weak thickness dependence on the left insulating spacer and the SF barrier while it shows a strong exponential decay on the thickness of the right insulating spacer similar to that of . This is due to the fact that of the right I-spacer which depends exponentially on NIR and is nearly independent of the thickness of the left I-barrier and the SF. Consequently, the ratio increases exponentially with NIL and NSF, while it remains approximately constant (~104) as NIR increases. These intriguing findings pave the way towards novel opportunities for the next-generation of multifunctional non-volatile memories based on field-like spin torque MRAM (FLST-MRAM), where the ‘writing’ processes can be achieved by manipulating via lower current densities. This in turn may resolve the bottleneck of high writing current densities required in the existing STT-MRAMs.
Figure 5 shows the bias dependence of in the SF-based tunnel junction with Δ = ±0.12 eV. Interestingly we predict that the field-like spin torque can be switched via a sign reversal of the SF’s exchange splitting, Δ, which can be achieved under reversal of the direction of an external magnetic field20,23, i.e. . This stems from the fact that the four individual NEIECs in Eq. (5) satisfy the relations: and , as can be inferred from the inset in Fig. 3(c). These results demonstrate the dual control of the giant field-like STT either via current or magnetic field which reverses the exchange splitting of the SF-barrier. The lower coercive field of EuS thin films (~60–150 Oe24) compared to that of the free FM film (~400–600 Oe for FeCo) may allow the magnetization switching of the SF magnetization via an external magnetic field without affecting the magnetization of the right FM film. Thus, the dual control of provides promising novel functionalities for both ‘reading’ and ‘writing’ processes in the newly proposed non-volatile FLST-MRAMs.
Figure 6(a) shows the variation of the field-like spin torque for the FM/I/SF/I/FM tunnel junction versus the exchange splitting, Δ, of the SF barrier which can be tuned, for example, by an external magnetic field. We find that varies linearly with the exchange splitting and its giant value remains robust provided that Δ ≠ 0. Note, that for Δ = 0 the field-like torque is reduced by four orders of magnitude. In order to examine the robustness of the giant field-like spin transfer torque against small fluctuations of the in-plane SF magnetization, MSF, from the easy z-axis, we show in Fig. 6(b) as a function of the angle, θSF, of the SF magnetization with respect to the z-axis in the x-z interfacial plane [inset in Fig. 6(b)]. We find that even though decreases with increasing θSF, its giant value remains robust except for , where the magnetization of the right FM becomes collinear with the magnetization of the SF and the giant spin accumulation at the right I/FM interface is reduced dramatically by four orders of magnitude.
In summary, we predict a giant field-like spin torque in FM/I/SF/I/FM junctions which has linear bias behavior, is independent of the SF-barrier thickness and whose sign can be toggled by switching the SF magnetization direction under an external magnetic field. These findings are in sharp contrast to those in conventional tunnel junctions based on nonmagnetic passive barriers where , has a quadratic bias behavior and decreases exponentially with the barrier thickness. The underlying origin is the giant interlayer exchange coupling between the noncollinear magnetization of the SF and free ferromagnetic electrode via the nonmagnetic insulator spacers. Our results suggest that the novel dual manipulation of either by a magnetic field or bias can be employed for ‘reading’ or ‘writing’ processes, respectively, in the next-generation FLST-MRAMs. We hope these predictions inspire further experimental explorations of STT in SF-based junctions, especially in Fe/MgO/EuO/MgO/Fe MTJs where one can exploit both the central SF barrier and the spin filter effect of the Fe/MgO stack on the Fe majority spin electrons at the Fermi energy with Δ1 symmetry.
Method
The Hamiltonian for the FM/I/SF/I/FM junction is described by the tight binding Hamiltonian7,35, H = HL + HR + HC + Hcpl, where HL, HR, HC are the Hamiltonian of the isolated left, right and central (I/SF/I) region, respectively and Hcpl is the coupling between the electrodes and the central scattering region. Within the single-band tight-binding model34 the Co majority- and minority-spin-dependent on-site energies are ε↑ = 1.0 eV and ε↓ = 2.5 eV, respectively, which describe correctly the position and exchange splitting of the Δ1 band in Co. The spin-dependent onsite energy of the EuS barrier are eV with Δ = 0.12 eV. The spin-independent onsite energy for the Al2O3 is εI = 5.98 eV and the nearest-neighbor hopping matrix element is t = −0.83 eV in all regions. These parameters are chosen to describe correctly (i) the average SF barrier height φ0 = 0.8 eV, (ii) the insulating barrier height φI = 1.0 eV and (iii) the exchange field Δ = ±0.12 eV in Al/EuS/Al2O3/Co30. However, the results do not depend on intricate details of the Co band structure and can be considered to be generally valid for partially spin-polarized FM, such as Fe or SrRuO3. The effect of external bias, V, is to shift the chemical potential of the right electrode with respect to that of the left electrode, μR − μL = eV and μL is fixed at the Fermi energy, EF = 0.0 eV.
Additional Information
How to cite this article: Tang, Y. -H. et al. Dual Control of Giant Field-like Spin Torque in Spin Filter Tunnel Junctions. Sci. Rep. 5, 11341; doi: 10.1038/srep11341 (2015).
References
Julliere, M. Tunneling between ferromagnetic films. Phys. Lett. 54A, 225–226 (1975).
Slonczewski, J.C. Conductance and exchange coupling of two ferromagnets separated by a tunneling barrier. Phys. Rev. B 39, 6995–7002 (1989).
Berger, L. Emission of spin waves by a magnetic multilayer traversed by a current. Phys. Rev. B 54, 9353–9358 (1996).
Stiles, M. D. & Zangwill, A. Anatomy of spin-transfer torque. Phys. Rev. B 66, 014407 (2002).
Haney, P. M., Heiliger, C. & Stiles, M. D. Bias dependence of magnetic exchange interactions: Application to interlayer exchange coupling in spin valves. Phys. Rev. B 79, 054405 (2009).
Slonczewski, J.C. Currents, torques and polarization factors in magnetic tunnel junctions. Phys. Rev. B 71, 024411 (2005).
Theodonis, I., Kioussis, N., Kalitsov, A., Chshiev, M. & Butler, W. H. Anomalous bias dependence of spin torque in magnetic tunnel junctions. Phys. Rev. Lett. 97, 237205 (2006).
Tang, Y. -H., Kioussis, N., Kalitsov, A., Butler, W. H. & Car, R. Controlling the nonequilibrium interlayer exchange coupling in asymmetric magnetic tunnel junctions. Phys. Rev. Lett. 103, 057206 (2009).
Kubota, H. et al. Quantitative measurement of voltage dependence of spin-transfer torque in MgO-based magnetic tunnel junctions. Nature Phys. 4, 37–41 (2008).
Sankey, J. C. et al. Measurement of the spin-transfer-torque vector in magnetic tunnel junctions. Nature Phys. 4, 67–71 (2008).
Wang, C., Cui, Y. -T., Katine, J. A., Buhrman, R. A. & Ralph, D. C. Time-resolved measurement of spin-transfer-driven ferromagnetic resonance and spin torque in magnetic tunnel junctions Nature Phys. 7, 496–501 (2011).
Ikeda, S, et al. Tunnel magnetoresistance of 604% at 300 K by suppression of Ta diffusion in CoFeB/MgO/CoFeB pseudo-spin-valves annealed at high temperature Appl. Phys. Lett. 93, 082508 (2008).
Wang, K. L., Alzate, J. G. & Amiri, P. K. Low-power non-volatile spintronic memory: STT-RAM and beyond. J. Phys. D: Appl. Phys. 46, 074003 (2013).
Tsymbal, E. Y. & Kohlstedt, H. Tunneling Across a Ferroelectric. Science 313, 181–183 (2006).
Velev, J. P., Jaswal, S. S. & Tsymbal, E. Y., Multi-ferroic and magnetoelectric materials and interfaces. Philos. Trans. R. Soc. London Sect. A 369, 3069 (2011).
Velev, J. P. et al. Effect of Ferroelectricity on Electron Transport in Pt/BaTiO3/Pt Tunnel Junctions. Phys. Rev. Lett. 98, 137201 (2007).
Garcia, V. et al. Ferroelectric Control of Spin Polarization. Science 327, 1106–1110 (2010).
Useinov, A., Kalitsov, A., Velev, J. & Kioussis, N. Bias-dependence of the tunneling electroresistance and magnetoresistance in multiferroic tunnel junctions. Appl. Phys. Lett. 105, 102403 (2014).
Useinov, A., Kalitsov, A., Velev, J. & Kioussis, N. Ferroelectric control of spin-transfer torque in multiferroic tunnel junctions. Phys. Rev. B 91, 094408 (2015).
Moodera, J. S., Meservey, R. & Hao, X. Variation of the electron-pin polarization in EuSe tunnel junctions from Zero to near 100% in a magnetic field. Phys. Rev. Lett. 70, 853 (1993).
Moodera, J. S., Hao, X., Gibson, G. A. & Meservey, R. Electron-spin polarization in tunnel junctions in zero applied field with ferromagnetic EuS barrier. Phys. Rev. Lett. 61, 637 (1988).
Santos, T. S. & Moodera, J. S. Observation of spin filtering with a ferromagnetic EuO tunnel barrier. Phys. Rev. B 69, 241203(R) (2004).
Moodera, J. S., Miao, G. X. & Santos, T. S. Frontiers in spin-polarized tunnelling. Phys. Today 63, 46 (2010).
Müller, M., Schreiber & Schneider, C. M. Magnetic properties of EuS spin filter tunnel contacts to silicon. J. Appl. Phys. 109, 07C710 (2011).
Lüders, U. et al. Spin filtering through ferrimagnetic NiFe2O4 tunnel barriers. Appl. Phys. Lett. 88, 082505 (2006).
Ramos, A. V. et al. Room temperature spin filtering in epitaxial cobalt-ferrite tunnel barriers. Appl. Phys. Lett. 91, 122107 (2007).
Nelson-Cheeseman, B. B. et al. Probing the role of the barrier layer in magnetic tunnel junction transport. Phys. Rev. B 76, 220410(R) (2007).
Gajek, M. et al. Spin filtering through ferromagnetic BiMnO3 tunnel barriers. Phys. Rev. B 72, 020406(R) (2005).
LeClair, P. et al. Large magnetoresistance using hybrid spin filter devices. Appl. Phys. Lett. 80, 625 (2002).
Nagahama, T., Santos, T. S. & Moodera, J. S. Enhanced magnetotransport at high bias in quasimagnetic tunnel junctions with EuS spin-filter barriers. Phys. Rev. Lett. 99, 016602 (2007).
Miao, G.-X., Müller, M. & Moodera, J. S. Magnetoresistance in double spin filter tunnel junctions with nonmagnetic electrodes and its unconventional bias dependence. Phys. Rev. Lett. 102, 076601 (2009).
Miao, G.-X., Chang, J., Assaf, B. A., Heiman, D. & Moodera, J. S. Spin regulation in composite spin-filter barrier devices. Nat. Comm. 5, 3682 (2014).
Eastman, D. E. Quasielastic Electron Scattering in EuO: A possible explanation for the observed paramagnetic spin-polarized photoemission. Phys. Rev. B 8, 6027 (1973).
Tang, Y. -H., Kioussis, N., Kalitsov, A., Butler, W. H. & Car, R. Influence of asymmetry on bias behavior of spin torque. Phys. Rev. B 81, 054437 (2010).
Kalitsov, A., Chshiev, M., Theodonis, I., Kioussis, N. & Butler, W. H. Spin-transfer torque in magnetic tunnel junctions. Phys. Rev. B 79, 174416 (2009).
Jia, X., Xia, K., Ke, Y. & Guo, H. Nonlinear bias dependence of spin-transfer torque from atomic first principles. Phys. Rev. B 84, 014401 (2011).
Tang, Y. -H. & Chu, F. -C. Interfacial spin-filter assisted spin transfer torque effect in Co/BeO/Co magnetic tunnel junction. J. Appl. Phys. 117, 093901 (2015).
Zeng, Z. M. et al. Effect of resistance-area product on spin-transfer switching in MgO-based magnetic tunnel junction memory cells. Appl. Phys. Lett. 98, 072512 (2011).
Acknowledgements
We thank Bao-huei Huang for technical support of analytical derivation. This work is supported by the Ministry of Science and Technology (Contract No. NSC 99-2112-M-008-020-MY3 and NSC 102-2112-M-008-004-MY3) and the National Center for Theoretical Sciences, Republic of China. The work at CSUN was supported by National Science Foundation (NSF) under Grant No. 1205734, NSF Partnerships for Research and Education in Materials (PREM) and by NSF under Grant No. 1160504 NSF Nanosystems Engineering Research Center for Translational Applications of Nanoscale Multiferroic Systems (TANMS).
Author information
Authors and Affiliations
Contributions
Y.H.T. conceived the study and made the analytical derivations. F.C.C. developed the tight-binding codes. N.K. gave scientific advice. All authors discussed the results and wrote the manuscript.
Ethics declarations
Competing interests
The authors declare no competing financial interests.
Rights and permissions
This work is licensed under a Creative Commons Attribution 4.0 International License. The images or other third party material in this article are included in the article’s Creative Commons license, unless indicated otherwise in the credit line; if the material is not included under the Creative Commons license, users will need to obtain permission from the license holder to reproduce the material. To view a copy of this license, visit http://creativecommons.org/licenses/by/4.0/
About this article
Cite this article
Tang, YH., Chu, FC. & Kioussis, N. Dual Control of Giant Field-like Spin Torque in Spin Filter Tunnel Junctions. Sci Rep 5, 11341 (2015). https://doi.org/10.1038/srep11341
Received:
Accepted:
Published:
DOI: https://doi.org/10.1038/srep11341
Comments
By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.