Interfacial properties and emulsion stability in fluorinated oil—non-fluorinated oil—surfactant(s) systems

doi:10.1016/0166-6622(92)80288-D

Colloids and Surfaces

Volume 67, 9 November 1992, Pages 81-93

https://doi.org/10.1016/0166-6622(92)80288-D Get rights and content

Abstract

The formation of interfaces and emulsions in systems comprising perfluoromethyldecalin (PFMD) and non-fluorinated oils with different polarities was investigated. The measured interfacial tension between the pure liquids was quantitatively interpreted in the framework of the Fowkes' model. The interfacial activity of several kinds of non-fluorinated, perfluorinated, ionic and non-ionic surfactants was explored. The perfluorinated non-ionic compound perfluoroalkyi-polyoxyethylene (PFPE) proved to be most effective as a surfactant in these systems. The critical micelle concentration and the areas per molecule at interfaces with non-fluorinated oils were determined for this substance. In some cases where fluorinated alcohols were used as co-surfactants, ultra-low interfacial tension and microemulsion formation were observed. The stability of the emulsion using PFPE as a surfactant was also investigated. It was shown that the higher polarity of the non-fluorinated oils led to higher emulsion stability. The addition of fluorinated alcohols decreased the stability and reversed the macroemulsion type. The observed effects are discussed from the viewpoint of the chemical structure of the compounds.

References (39)

D.G. LeGrand et al.
J. Colloid Interface Sci.
(1975)
R.E. Johnson et al.
J. Colloid Interface Sci.
(1966)
I. Rico et al.
R.N. Haszeldine
J. Chem. Soc.
(1949)
H. Saito et al.
J. Colloid Interface Sci.
(1970)
A.D. Nikolov et al.
J. Colloid Interface Sci.
(1989)
A.D. Nikolov et al.
J. Colloid Interface Sci.
(1989)
(1984)
J. Boyd et al.
J. Colloid Interface Sci.
(1972)
A. Graciaa et al.
Langmuir
(1989)

K. Shinodi et al.

J. Phys. Chem.

(1972)

J.C. Ravey et al.

Prog. Colloid Polym. Sci.

(1988)

M.K. Sharma

Prog. Colloid Polym. Sci.

(1978)

M.K. Sharma

Prog. Colloid Polym. Sci.

(1978)

M.K. Sharma

Prog. Colloid Polym. Sci.

(1978)

P.D. Fletcher et al.

J. Chem. Soc.

(1984)

S.E. Friberg et al.

Langmuir

(1988)

I. Rico et al.

J. Colloid Interface Sci.

(1984)

I. Rico et al.

Nouv. J. Chim.

(1984)

M.C. Malet-Martino et al.

S. Magdassi et al.

J. Dispersion Sci. Technol.

(1986)

Cited by (18)

Stabilization of non-aqueous emulsions by poly(2-vinylpyridine)-b-poly(butadiene) block copolymers
2014, Colloids and Surfaces A: Physicochemical and Engineering Aspects
Citation Excerpt :
In the early seventies, it was shown for the first time by Periard et al. [5] that polyA-b-polyB block copolymers are by far more efficient than low molecular weight surfactants for the steric stabilization of non-aqueous emulsions formed by two non-miscible solvents SA and SB, which are selective solvents for poly A and poly B sequences, respectively. Over the last years, this concept of block copolymer stabilized non-aqueous emulsions was confirmed by different authors [6–12]. For instance, Cameron and Sherrington [10] as well as Imhof and Pine [12] demonstrated the increased stabilization effect of the block copolymers with respect to classical low molecular weight surfactants.
Non-aqueous sub-micron biocompatible emulsions, which are of interest for biomedical and cosmetic formulations, were developed for the system polyethylene glycol (PEG 400) dispersed in a typical liquid glycerine ester (Miglyol 812). These emulsions were stabilized by poly(2-vinylpyridine)-b-poly(butadiene) (P2VP-b-PBut) copolymers, each of these sequences being well adapted to the solubility parameters of the two liquid phases. A comparative study of the emulsifying and stabilization efficiency was performed for two copolymers with quasi-identical molecular weights but of different compositions, such as P2VP₅₀-b-PBut₁₂₈ (A) and P2VP₃₇-b-PBut₁₈₉ (B). These block copolymers form in Miglyol 812 star-like micelles having a P2VP core and a PBut corona. The PEG 400/Miglyol 812 emulsion characteristics were determined as a function of the dispersed phase volume fractions and of the copolymer concentrations. At constant concentrations, copolymer B, with longer Miglyol 812 soluble PBut chains, appeared to be more efficient as emulsifier and stabilizer than copolymer A. By combination of the two block copolymer, a synergetic emulsifying and stabilizing effect could be achieved.
Fluorosurfactants for microdroplets: Interfacial tension analysis
2010, Journal of Colloid and Interface Science
Citation Excerpt :
This paper presents a quantification of the properties of several potential fluorosurfactants, synthesised for use within a microfluidic environment, and correlates these properties with their ability to stabilise the fluorous oil–water interface within such an environment. While literature on both the synthesis and analysis of fluorous surfactants is vast [10–16], studies combining an analysis of surfactant properties with a demonstration of their application to microfluidics are rare. It is this lacuna that this paper aims to fill, in the hope that this will further the understanding of the interactions between surfactant and liquid phases, and permit the future creation of more effective surfactants.The surfactants discussed in this paper are shown to be effective in generating stable water droplets within streams of fluorous oil in PDMS microfluidic devices, and their surfactant properties compare well with studies on similar molecules.
Quantitative analysis of a number of potential fluorous surfactants, prepared with a view to stabilisation of microdroplets in microfluidic systems is presented. The surfactants tested comprised compounds with both perfluoropolyether (PFPE) and perfluoroalkyl (PFA) tails, along with three classes of hydrophilic head group, including crown ethers and hexaethylene gylcol. Surfactants were tested for activity using the pendant drop technique. Six compounds proved highly effective and efficient surfactants, with γ_CMC < 10 mN/m and CMCs in the sub-millimolar range. These six compounds stabilised aqueous microdroplets in fluorous oils within poly(dimethylsiloxane) (PDMS) microdevices to a greater degree than commonly used pseudosurfactants such as perfluorooctanol.
Chapter 13 Two-Dimensional Crystallization Of Particulates And Proteins
2001, Studies in Interface Science
Citation Excerpt :
The quality of the obtained 2D ordered arrays was found to increase with the increase of the particle charge, which can be attributed to the enhanced particle-substrate and particle-particle repulsion. In a subsequent experimental study Matsushita et al. [181] applied their technique to create large 2D arrays of ordered SiO2 particles, which were further used as a matrix for fabrication of mesoporous structured TiO2 films exhibiting photocatalytic activity. In the previous sections of this chapter we considered two-dimensional structuring of particles in wetting films formed on substrates.
Lateral forces acting between particles in liquid films or lipid membranes
1997, Advances in Biophysics
To investigate the mechanism of formation of 2D arrays of protein macromolecules in liquid films we carried out model experiments with μm-sized latex particles. The direct observations revealed that the process of ordering is triggered by attractive lateral capillary forces due to the overlap of the menisci formed around the particles. Two types of lateral capillary forces, flotation and immersion, can be distinguished, and a theory of these interactions is developed. Similar forces are operative between inclusions (proteins) incorporated in lipid membranes. We develop an appropriate model of a lipid bilayer, which is described as an elastic layer (the hydrocarbon chain region) sandwiched between two Gibbs dividing surfaces (the two headgroup regions). The range of the interaction between two cylindrical inclusions turns out to be of the order of several inclusion radii. The results, which are in qualitative agreement with the experimental observations, can be applied to the interpretation of membrane processes and mechanisms such as protein aggregation in lipid membranes.
Interfacial properties and emulsification in systems of perfluoropolyether/non-fluorinated oil/partially fluorinated oligomeric and polymeric compounds
1996, Colloids and Surfaces A: Physicochemical and Engineering Aspects
Interfacial properties and emulsification were studied in the systems perfluoropolyether (PFPE)/non-fluorinated oil (NFO)/partially fluorinated oligomeric or polymeric compounds (Rf-Rh). All the Rf-Rh compounds were synthesized. The polymeric Rf-Rh compounds were random and graft copolymers with 1H,1H,2H,2H-heptadecafluorodecyl acrylate (17FA) repeating units introduced into a trunk polymer chain. The Rf-Rh compounds dissolved or dispersed in most NFOs, but did not dissolve in PFPE. They depressed interfacial tensions at PFPE-toluene interfaces, which were mainly used in this study, with an increase in their concentrations. The polymeric Rf-Rh compounds were effective emulsifying agents for the formation of macroemulsions. The graft copolymers permitted the formation of very stable emulsions w ith a droplet diameter of about 200 nm, in particular. No direct relationship was found between the depression of the interfacial tensions and the stability of the emulsions. However, low interfacial tensions and sterically stable protection of an adsorbed film served for the formation of small-sized emulsion droplets, which contributed to reduce the sedimentation due to the gravitational force.
Dynamic surface and interfacial tensions of surfactant and polymer solutions
1994, Advances in Colloid and Interface Science
Dynamic surface and interfacial tensions are the most frequently measured non-equilibrium properties of adsorption layers at liquid interfaces. The review presents the theoretical basis of adsorption kinetics, taking into consideration different adsorption mechanisms, and specific experimental conditions, such as liquid flow and interfacial area changes. Analytical solutions, if available, approximations as well as numerical procedures for direct solution of the physical models are presented.
Several experimental techniques are discussed frequently used in studies of the dynamic adsorption behaviour of surfactants and polymers at liquid interfaces: drop volume, maximum bubble pressure, and pendent drop technique, drop pressure tensiometry, pulsating bubble and elastic ring method. Experimental results, most of all obtained with different technique on one and the same surfactant system, are then discussed on the basis of current theories.
Finally, the role of dynamic interfacial properties in several practical applications is discussed: foam and emulsion film formation and stabilisation, rising of bubbles and drops in a surfactant solution.

View all citing articles on Scopus

View full text