Skip to main content

Advertisement

Springer Nature Link
Log in

Utilization of biomass waste for activated carbon production by steam gasification in a rotary reactor: experimental and theoretical approach

  • Original Article
  • Published:
Biomass Conversion and Biorefinery Aims and scope Submit manuscript

Abstract

In order to produce cheap activation carbon for dioxin adsorption in waste incinerator, waste plywood, pinewood, and coconut shell were used as raw materials to produce activated carbon via steam gasification on a lab-scaled rotary reactor. The influence of temperature, steam flow rate, and activation time on activated carbon yield and properties was investigated. Experimental results show that at 800 years, with 30-min activation time and steam/char ratio equal to 2, the yield of plywood activated carbon reached 60.5%, which was much higher than pinewood. The iodine adsorption value was 943 mg/g, which is close to pinewood. The pore structure analysis results show that the activated carbon derived from pinewood and plywood is similar. The pores with diameter of 2–5 nm were well developed, which was suitable for dioxin adsorption in waste incinerator. In the end, the computational fluid dynamics (CFD) and discrete element method (DEM) were used for modeling and optimization of the rotary furnace. Calculation results show that internal friction between the particles or the degree of anisotropy of the particles will cause the particles in the furnace to form a larger accumulation inclination, which benefits the mixing of the material in furnace. The results show that both the Eulerian-Eulerian two-fluid method and the DEM can simulate the movement of particles in the rotary furnace.

The activated carbon produced by steam gasification for dioxin adsorption.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Subscribe and save

Springer+ Basic
$34.99 /Month
  • Get 10 units per month
  • Download Article/Chapter or eBook
  • 1 Unit = 1 Article or 1 Chapter
  • Cancel anytime
Subscribe now

Buy Now

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Fig. 9
Fig. 10
Fig. 11
Fig. 12

Similar content being viewed by others

References

  1. Tay T, Ucar S, Karagoz S (2009) Preparation and characterization of activated carbon from waste biomass. J Hazard Mater 165(1):481–485

    Article  Google Scholar 

  2. Köseoğlu E, Akmil-Başar C (2015) Preparation, structural evaluation and adsorptive properties of activated carbon from agricultural waste biomass. Adv Powder Technol 26(3):811–818

    Article  Google Scholar 

  3. Derlet RW, Albertson TE (1986) Activated charcoal--past, present and future. West J Med 145(4):493–496

    Google Scholar 

  4. Guo Y, Li Y, Zhu T, Wang J, Ye M (2016) Modeling of dioxin adsorption on activated carbon. Chem Eng J 283:1210–1215

    Article  Google Scholar 

  5. Mukherjee A, Debnath B, Ghosh SK (2016) A review on technologies of removal of dioxins and furans from incinerator flue gas. Procedia Environ Sci 35:528–540

    Article  Google Scholar 

  6. Kulkarni PS, Crespo JG, Afonso CAM (2008) Dioxins sources and current remediation technologies — a review. Environ Int 34(1):139–153

    Article  Google Scholar 

  7. Long RQ, Yang RT (2001) Carbon nanotubes as superior sorbent for dioxin removal. J Am Chem Soc 123(9):2058–2059

    Article  Google Scholar 

  8. Hajizadeh Y, Williams PT (2013) Activated carbon production from RDF and its use for dioxin removal from flue gas of waste incinerators. Int J Environ Health Eng 2(1):10

    Article  Google Scholar 

  9. Czajczyńska D, Anguilano L, Ghazal H, Krzyżyńska R, Reynolds AJ, Spencer N, Jouhara H (2017) Potential of pyrolysis processes in the waste management sector. Therm Sci Eng Prog 3:171–197

    Article  Google Scholar 

  10. Hirata T, Inoue M, Fukui Y (1992) Pyrolysis and combustion toxicity of wood treated with CCA. Wood Sci Technol 27(1):35–47

    Article  Google Scholar 

  11. Fateh T, Rogaume T, Luche J, Richard F, Jabouille F (2014) Characterization of the thermal decomposition of two kinds of plywood with a cone calorimeter – FTIR apparatus. J Anal Appl Pyrolysis 107:87–100

    Article  Google Scholar 

  12. Kim YH (2011) Process simulation of activated carbon production using a rotary kiln. Korean J Chem Eng 28:27–31

    Article  Google Scholar 

  13. Miguel GS, Fowler GD, Dall’Orso M, Sollars CJ (2002) Porosity and surface characteristics of activated carbons produced from waste tyre rubber. J Chem Technol Biotechnol 77(1):1–8

    Article  Google Scholar 

  14. Zhao Chuang WZ-X (2020) Application of a new type of internal heating activation furnace system in production. Chem Fertil Des 58(1):3

    Google Scholar 

  15. Zhe L (2003) Discussion on activated technology of SLEP furnace. TONG MEI KEJI 96:3

    Google Scholar 

  16. Yinw X (2014) Current status and development trend of coal-based activated carbon production equipment in China. Clean Coal Technol

  17. Liu H, Yin H, Zhang M, Xie M, Xi X (2016) Numerical simulation of particle motion and heat transfer in a rotary kiln. Powder Technol 287:239–247

    Article  Google Scholar 

  18. Sebastian Escotet-Espinoza M, Foster CJ, Ierapetritou M (2018) Discrete element modeling (DEM) for mixing of cohesive solids in rotating cylinders. Powder Technol 335:124–136

    Article  Google Scholar 

  19. Hlosta J, Jezerská L, Rozbroj J, Žurovec D, Zegzulka J (2020) DEM Investigation of the influence of particulate properties and operating conditions on the mixing process in rotary drums: Part 2—Process Validation and Experimental Study. Processes 8(2):184

    Article  Google Scholar 

  20. Zhao S, Zhang Y, Su Y (2019) Experimental investigation of rice straw oxidative pyrolysis process in a hot-rod reactor. J Anal Appl Pyrolysis 142:104646

    Article  Google Scholar 

  21. Gonzalez MT, Molinasabio M, Rodriguezreinoso F (1994) Steam activation of olive stone chars, development of porosity. Carbon 32(8):1407–1413

    Article  Google Scholar 

  22. Kang HS (2005) Theoretical study of binding of metal-doped graphene sheet and carbon nanotubes with dioxin. J Am Chem Soc 127(27):9839–9843

    Article  Google Scholar 

  23. Wang R, Zhang D, Liu C (2017) DFT study of the adsorption of 2,3,7,8-tetrachlorodibenzo-p-dioxin on pristine and Ni-doped boron nitride nanotubes. Chemosphere 168:18–24

    Article  Google Scholar 

  24. Wu FC, Tseng RL, Juang RS (2005) Comparisons of porous and adsorption properties of carbons activated by steam and KOH. J Colloid Interface Sci 283(1):49–56

    Article  Google Scholar 

  25. Atkinson JD, Hung PC, Zhang Z, Chang M, Yan Z, Rood MJ (2014) Adsorption and destruction of PCDD/Fs using surface-functionalized activated carbons. Chemosphere 118C:136–142

    Google Scholar 

  26. Li W, Yang K, Peng J, Zhang L, Guo S, Xia H (2008) Effects of carbonization temperatures on characteristics of porosity in coconut shell chars and activated carbons derived from carbonized coconut shell chars. Ind Crop Prod 28(2):190–198

    Article  Google Scholar 

  27. Bell JG, Zhao X, Uygur Y, Thomas KM (2011) Adsorption of chloroaromatic models for dioxins on porous carbons: the influence of adsorbate structure and surface functional groups on surface interactions and adsorption kinetics. J Phys Chem C 115(6):2776–2789

    Article  Google Scholar 

  28. Liu Y, Su F-Y, Wen Z, Li Z, Yong H-Q, Feng X-H (2014) CFD Modeling of flow, temperature, and concentration fields in a pilot-scale rotary hearth furnace. Metall Mater Trans B Process Metall Mater Process Sci 45(1):251–261

    Article  Google Scholar 

  29. Li D, Liu G, Lu H, Zhang Q, Wang Q, Yu H (2016) Numerical simulation of different flow regimes in a horizontal rotating ellipsoidal drum. Powder Technol 291:86–96

    Article  Google Scholar 

  30. Komossa H, Wirtz S, Scherer V, Herz F, Specht E (2014) Transversal bed motion in rotating drums using spherical particles: comparison of experiments with DEM simulations. Powder Technol 264:96–104

    Article  Google Scholar 

  31. Hlungwani O, Rikhotso J, Dong H, Moys MH (2003) Further validation of DEM modeling of milling: effects of liner profile and mill speed. Miner Eng 16(10):993–998

    Article  Google Scholar 

  32. Henein H, Brimacombe JK (1983) The modeling of transverse solids motion in rotary kilns. Metall Urgical Trans B 14:14

    Google Scholar 

  33. Mellman J (2001) The transverse motion of solids in rotating cylinders-forms of motion and transition behavior. Powder Technol 118:20

    Article  Google Scholar 

Download references

Funding

This work was supported by Science Foundation of Nanjing Institute of Technology (YKJ201813)

Author information

Authors and Affiliations

  1. Nanjing Institute of Technology, Nanjing, China

    Shanhui Zhao & Linghai Chen

  2. Shanghai Jiao Tong University, Shanghai, China

    Shanhui Zhao

Authors
  1. Shanhui Zhao
    View author publications

    You can also search for this author inPubMed Google Scholar

  2. Linghai Chen
    View author publications

    You can also search for this author inPubMed Google Scholar

Corresponding author

Correspondence to Shanhui Zhao.

Additional information

Publisher’s Note

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Zhao, S., Chen, L. Utilization of biomass waste for activated carbon production by steam gasification in a rotary reactor: experimental and theoretical approach. Biomass Conv. Bioref. 12, 3943–3953 (2022). https://doi.org/10.1007/s13399-020-00921-9

Download citation

  • Received:

  • Revised:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s13399-020-00921-9

Keywords