Abstract
xYb2O3–15(20Ni–Cu)/(85 − x)(NiFe2O4–10NiO) (x = 0, 0.25, 0.5, 0.75, 1.0, 2.0, and 10.0) cermets for aluminum electrolysis were prepared to investigate the effect of Yb2O3 doping on the grain boundary of the cermets after sintering. The results showed that each interface was very clear and that with increasing Yb2O3 content, most of the Yb was evenly distributed at the grain boundary. Moreover, according to the phase composition and microstructural analysis by X-ray diffraction (XRD), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX), and electron probe microanalysis (EPMA), YbFeO3 was produced along the grain boundary. The YbFeO3 was concluded to not only have formed from the interaction between the NiFe2O4 or Fe2O3 component and Yb2O3 at the grain boundary of the cermets, but also from the decomposition of NiFe2O4 into NiO and Fe2O3 and the subsequent reaction of Fe2O3 with Yb2O3. Thus, the production of YbFeO3 resulted in a cermet with high relative density, good electrical conductivity, and good corrosion resistance.
Similar content being viewed by others
References
R.P. Pawlek, Inert anodes: an update, [in] Light Metals 2004, TMS, North Carolina, 2004, p. 283.
R.P. Pawlek, Inert anodes: an update, [in] Light Metals 2008, TMS, Louisiana, 2008, p. 1039.
K.C. Zhou and Y.Q. Tao, Research development of nickel ferrite based cermet inert anode materials, Chin. J. Nonferrous Met., 21(2011), No. 10, p. 2418.
Z.L. Tian, Y.Q. Lai, Z.Y. Li, J. Li, K.C. Zhou, and Y.X. Liu, Cup-shaped functionally gradient NiFe2O4-based cermet inert anodes for aluminium reduction, JOM, 61(2009), No. 5, p. 34.
J. Li, G. Zhang, Y.Q Lai, Y. Zhang, and Z.L. Tian, Densification and sintering dynamics of 10NiO-NiFe2O4 composites doped with CaO, J. Cent. South Univ. Technol., 14(2007), No. 5, p. 629.
T. Luo, Z.W. Wang, B.L. Gao, X.G. Yu, and Z.X. Qiu, Preparation of a cermet inert anode based on ferrous nickel and its use in an electrolysis study, [in] Light Metals 2005, TMS, California, 2005, p. 541.
E. Olsen and J. Thonstad, Nickel ferrite as inert anodes in aluminium electrolysis: Part I. Material fabrication and preliminary testing, J. Appl. Electrochem., 29(1999), No. 3, p. 293.
H. Xiao, R. Hovland, S. Rolseth, and J. Thonstad, Studies on the corrosion and the behavior of inert anodes in aluminum electrolysis, Metall. Mater. Trans. B, 27(1996), No. 2, p. 185.
H.B. He, K.C. Zhou, Z.Y. Li, and B.Y. Huang, Effect of BaO addition on electric conductivity of xCu/NiFe2O4-10NiO cermets, Trans. Nonferrous Met. Soc. China, 18(2008), No. 5, p. 1134.
H.B. He, F. Liu, Y.F. Song, and H.N. Xiao, Effect of coated spinel NiFe2O4 on the surface of metal phase 20Ni-80Cu on corrosion resistance of 15(20Ni-Cu)/(NiFe2O4?10NiO) cermet for aluminum electrolysis, Funct. Mater., 43(2012), No. 15, p. 2111.
Y.Q. Tao, Z.Y. Li, and K.C. Zhou, Effects of debinding atmosphere on the microstructure and sintering densification of nickel ferrite, Ceram. Int., 39(2013), No. 1, p. 865.
Y.Q. Tao, Z.Y. Li, Z. Dou, H.W. Xiong, and K.C. Zhou, Microstructural evolution of a nickel ferrite–copper alloy cermet during sintering and high-temperature oxidation, J. Am. Ceram. Soc., 95(2012), No. 10, p. 3031.
Y.Q. Tao, Z.Y. Li, L. Zhang, X.P. Gan, and K.C. Zhou, Preparation of nickel ferrite-copper composite by pressureless infiltration, J. Am. Ceram. Soc., 95(2012), No. 12, p. 3739.
J.H. Xi, G.C. Yao, Y.H. Liu, and X.M. Zhang, Effect of additive vanadic oxide on conductivity of nickel ferrite-based cermets inert anodes, J. Chin. Ceram. Soc., 34(2006), No. 1, p. 34.
O.A. Lorentsen and J. Thonstad, Electrolysis and post-testing of inert cermet anodes, [in] Light Metals 2002, TMS, Washington, 2002, p. 443.
E. Olsen and J. Thonstad, Nickel ferrite as inert anodes in aluminum electrolysis: Part II. Material performance and long-term testing, J. Appl. Electrochem., 29(1999), No. 3, p. 301.
J.Y. Liu, Z.Y. Li, Y.Q. Tao, D. Zhang, and K.C. Zhou, Phase evolution of 17(Cu-10Ni)-(NiFe2O4-10NiO) cermet inert anode during aluminum electrolysis, Trans. Nonferrous Met. Soc. China, 21(2011), No. 3, p. 566.
B.G. Liu, L. Zhang, K.C. Zhou, Z.Y. Li, and H. Wang, Electrical conductivity and molten salt corrosion behavior of spinel nickel ferrite, Solid State Sci., 13(2011), No. 8, p. 1483.
H.B. He and Z.H. Chen, Corrosion behavior of NiFe2O4-10NiO based cermet inert anode surface for aluminum electrolysis, Metal. Int., 18(2013), No. 10, p. 58.
H.B. He, Y. Wang, J.J. Long, and Z.H. Chen, Corrosion of NiFe2O4-10NiO based cermet inert anode for aluminium electrolysis, Trans. Nonferrous Met. Soc. China, 23 (2013), No. 12, p. 3816.
H.B. He, Formation law of dense NiFe2O4-NiAl2O4-FeAl2O4 ceramic layer on the surface of NiFe2O4 based ceramic inert anode for aluminium electrolysis, Mater. Res. Innov., 18(2014), No. 2, p. 182.
H.B. He, Behaviour and material properties of the grain boundary on the surface of an anode during the formation of a dense layer, Appl. Mech. Mater., 508(2014), p. 61.
H.B. He and H.N. Xiao, Effect of Yb2O3 doping on performances of 15(20Ni-Cu)/(NiFe2O4-10NiO) cermets, Chin. J. Nonferrous Met., 21(2011), No. 3, p. 611.
S.R. Robert, N. Taki, and P.C. Lawrence. Phase diagrams for ceramists Volume IV. American Ceramic Society, Columbus, Ohio, 1981, p. 44.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
He, Hb. Effect of Yb2O3 doping on the grain boundary of NiFe2O4–10NiO-based cermets after sintering. Int J Miner Metall Mater 22, 1334–1341 (2015). https://doi.org/10.1007/s12613-015-1202-z
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12613-015-1202-z