Abstract
The potential for thermoelectric power generation (via waste heat recovery onboard automobiles) to displace alternators and/or provide additional charging to a vehicle battery pack has increased with recent advances in thermoelectric material processing. In gasoline fueled vehicles (GFVs), about 40% of fuel energy is wasted in exhaust heat, while a smaller amount of energy (30%) is ejected through the engine coolant. Therefore, exhaust-based thermoelectric generators (ETEG) have been a focus for GFV applications since the late 1980s. The conversion efficiency of modern thermoelectric materials has increased more than three-fold in the last two decades; however, disputes as to the thermal design of ETEG systems has kept their overall efficiency at limited and insufficient values. There are many challenges in the thermal design of ETEG systems, such as increasing the efficiency of the heat exchangers (hot box and cold plate), maintaining a sufficient temperature difference across the thermoelectric modules during different operating conditions, and reducing thermal losses through the system as a whole. This paper focuses on a review of the main aspects of thermal design of ETEG systems through various investigations performed over the past twenty years. This paper is organized as follows: first, the construction of a typical ETEG is described. The heat balance and efficiency of ETEG are then discussed. Then, the third section of this paper emphasizes the main objectives and challenges for designing efficient ETEG systems. Finally, a review of ETEG research activities over the last twenty years is presented to focus on methods used by the research community to address such challenges.
Similar content being viewed by others
References
Bass, J., Campana, R. J. and Elsner, N. B. (1992). Thermoelectric generator development for heavy-duty truck applications. Proc. Annual Automotive Technology Development Contractors Coordination Meeting, Dearborn, USA, 743–748.
Bass, J., Elsner, N. B. and Leavitt, A. (1995). Performance of the 1 kW thermoelectric generator for diesel engines. Proc. 13th Int. Conf. Thermoelectrics B, Mathiprakisam, edn., AIP Conf. Proc., New York, 295.
Hi-Z Inc. (1996). Use, Applications, and Testing of Hi-Z Thermoelectric Modules. Hi-Z Inc: Online Catalog available at: http://www.hi-z.com/how-to.htm
Ikoma, K., Munekiyo, M., Furuya, K., Kobayashi, M., Izumi, T. and Shinohara, K. (1998). Thermoelectric module and generator for gasoline engine vehicle. Proc. 17th Int. Conf. Thermoelectrics. IEEE, Nagoya, Japan, 464–467.
Kushch, A. S., Bass, J. C., Ghamaty, S. and Elsner, N. B. (2001). Thermoelectric development at Hi-Z technology. Proc. 20th Int. Conf. Thermoelectrics, Beijing, China, 422–430.
Neild, Jr, A. B. (1963). Portable Thermoelectric Generators. SAE-645A. Society of Automotive Engineers. New York.
Rowe, D. M. and Bhandari, C. M. (1983). Modern Thermoelectrics. Reston Publishing Inc. Virginia. 93–100.
Rowe, D. M. Edn. (2005). Thermoelectrics Handbook. Macro to Nano. CRC Press. Florida, 1. Section 52-2.
Saqr, K. M. and Musa, M. N. (2007). State of the art of thermoelectric generators for waste heat recovery applications. J. Teknos-2k 7,2, 22–30.
Thacher, E. F., Helenbrook, B. T., Karri, M. A. and Richter, C. J. (2006). Progress in Thermoelectrical Energy Recovery from a Light Truck Exhaust. Paper Presentation at the DEER Conf.. Available on: www1.eere.energy.gov/vehiclesandfuels/pdfs/deer_2006/session6/2006_deer_thacher.pdf
Thacher, E. F., Helenbrook, B. T., Karri, M. A. and Richter, C. J. (2007). Testing of an automobile exhaust thermoelectric generator in a light truck. Proc. I MECH E, Part D: J. Automobile Engineering 221,1, 950–107.
Va’zquez, J., Sanz-Bobi, M. A. Palacios, R. and Arenas, A. (2002). State of the art of thermoelectric generators based on heat recovered from the exhaust gases of automobiles. Proc. 7th European Workshop on Thermoelectrics, Pampelona, Spain.
Yang, J. (2005). Potential applications of thermoelectric waste heat recovery in the automotive industry. Proc. 24th Int. Conf. Thermoelectrics. Clemson University, U.S.A: IEEE, 155–160.
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Saqr, K.M., Mansour, M.K. & Musa, M.N. Thermal design of automobile exhaust based thermoelectric generators: Objectives and challenges. Int.J Automot. Technol. 9, 155–160 (2008). https://doi.org/10.1007/s12239-008-0020-y
Received:
Revised:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12239-008-0020-y