Abstract
The present paper addresses the optimal heat release (HR) law in a single cylinder engine operated under reactivity controlled compression ignition (RCCI) combustion mode to minimise the indicated specific fuel consumption (ISFC) subject to different constraints including pressure related limits (maximum cylinder pressure and maximum cylinder pressure gradient). With this aim, a 0-dimensional (0D) engine combustion model has been identified with experimental data. Then, the optimal control problem of minimising the ISFC of the engine at different operating conditions of the engine operating map has been stated and analytically solved. To evaluate the method viability a data-driven model is developed to obtain the control actions (gasoline fraction) leading to the calculated optimal HR, more precisely to the optimal ratio between premixed and diffusive combustion. The experimental results obtained with such controls and the differences with the optimal HR are finally explained and discussed.
Similar content being viewed by others
References
F. Payri, J. M. Luján, C. Guardiola, et al. A challenging future for the IC engine: New technologies and the control role. Oil & Gas Science and Technology–Revue D IFP Energies Nouvelles, 2015, 70(1): 15–30.
H. Yanagihara, Y. Sato, J. Minuta. A simultaneous reduction in NOx and soot in diesel engines under a new combustion system (Uniform Bulky Combustion System–UNIBUS). Proceedings of the 17th international Vienna Motor Symposium, Vienna, 1996: 303–314.
D. A. Splitter, M. L. Wissink, T. L. Hendricks, et al. Comparison of RCCI, HCCI, and CDC operation from low to full load. THIESEL 2012 conference on thermo-and fluid dynamic processes in direct injection engines. Valencia, 2012.
J. Benajes, J. V. Pastor, A. García, et al. The potential of RCCI concept to meet EURO VI NOx limitation and ultra-low soot emissions in a heavy-duty engine over the whole engine map. Fuel, 2015, 159(1): 952–961.
J. Benajes, A. García, J. Monsalve-Serrano, et al. An assessment of the dual-mode reactivity controlled compression ignition/conventional diesel combustion capabilities in a EURO VI medium-duty diesel engine fueled with an intermediate ethanol-gasoline blend and biodiesel. Energy Conversion and Management, 2016, 123(1): 381–391.
S. Molina, A. García, J. M. Pastor, et al. Operating range extension of RCCI combustion concept from low to full load in a heavy-duty engine. Applied Energy, 2015, 143: 211–227.
D. A. Splitter, R. D. Reitz. Fuel reactivity effects on the efficiency and operational window of dual-fuel compression ignition engines. Fuel, 2014, 118(5): 163–175.
J. Benajes, S. Molina, A. García, et al. Effects of low reactivity fuel characteristics and blending ratio on low load RCCI (reactivity controlled compression ignition) performance and emissions in a heavy-duty diesel engine. Energy, 2015, 90: 1261–1271.
J. Benajes, S. Molina, A. García, et al. An investigation on RCCI combustion in a heavy duty diesel engine using incylinder blending of diesel and gasoline fuels. Applied Thermal Engineering, 2014, 63(1): 66–76.
J. Li, W. M. Yang, H. An, et al. Numerical investigation on the effect of reactivity gradient in an RCCI engine fueled with gasoline and diesel. Energy Conversion and Management, 2015, 92(1): 342–352.
J. Benajes, S. Molina, A. García, et al. Effects of direct injection timing and blending ratio on RCCI combustion with different low reactivity fuels. Energy Conversion and Management, 2015, 99(1): 193–209.
J. Benajes, J. V. Pastor, A. García, et al. A RCCI operational limits assessment in a medium duty compression ignition engine using an adapted compression ratio. Energy Conversion and Management, 2016, 126(1): 497–508.
F. Zurbriggen, T. Ott, C. Onder, et al. Optimal control of the heat release rate of an internal combustion engine with pressure gradient, maximum pressure, and knock constraints. Journal of Dynamic Systems, Measurement, and Control, 2014, 136(6): DOI 10.1115/1.4027592.
L. Eriksson, M. Sivertsson. Computing optimal heat release rates in combustion engines. SAE International Journal of Engines, 2015, 8(3): 1069–1079.
L. Eriksson, M. Sivertsson. Calculation of optimal heat release rates under constrained conditions. SAE International Journal of Engines, 2016, 9(2): 1143–1162.
Y. Zhang, T. Shen. Model based combustion phase optimization in SI engines: Variational analysis and spark advance determination. IFAC-PapersOnLine, 2016, 49(11): 679–684.
F. Payri, P. Olmeda, J. Martín, et al. A new tool to perform global energy balances in DI diesel engines. SAE International Journal of Engines, 2014, 7(7): 43–59.
S. Yu, M. Zheng. Ethanol-diesel premixed charge compression ignition to achieve clean combustion under high loads. Proceedings of the Institution of Mechanical Engineers–Part D: Journal of Automobile Engineering, 2016, 30(4): 527–541.
D. Klos, D. Janecek, S. Kokjohn. Investigation of the combustion instability-NOx tradeoff in a dual fuel reactivity controlled compression ignition (RCCI) engine. SAE International Journal of Engines, 2015, 8(2): 821–830.
G. Woschni. A Universally Applicable Equation for the Instantaneous Heat Transfer Coefficient in the Internal Combustion Engine. SAE Technical Paper. 1967: DOI 10.4271/670931.
C. Guardiola, J. López, J. Martín, et al. Semi-empirical in-cylinder pressure based model for NOx prediction oriented to control applications. Applied Thermal Engineering, 2011, 31(16): 3275–3286.
C. Guardiola, J. Martín, B. Pla, et al. Cycle by cycle NOx model for diesel engine control. Applied Thermal Engineering, 2017, 110: 1011–1020.
J. M. Desantes, J. J. López, P. Redón, et al. Evaluation of the Thermal NO formation mechanism under low temperature diesel combustion conditions. International Journal of Engine Research, 2012, 13(6): 531–539.
O. Sundstrm, L. Guzzella. A generic dynamic programming Matlab function. IEEE International Conference on Control Applications/International Symposium on Intelligent Control, St Petersburg: IEEE, 2009: 1625–1630.
J. Benajes, A. García, J. M. Pastor, et al. Effects of piston bowl geometry on reactivity controlled compression ignition heat transfer and combustion losses at different engine loads. Fuel, 2016, 98(1): 64–77.
J. Benajes, J. V. Pastor, A. García, et al. An experimental investigation on the influence of piston bowl geometry on RCCI performance and emissions in a heavy-duty engine. Energy Conversion and Management, 2015, 103: 1019–1031.
J. M. Desantes, J. Benajes, A. García, et al. The role of the incylinder gas temperature and oxygen concentration over low load RCCI combustion efficiency. Energy, 2014, 78(SI): 854–868.
Author information
Authors and Affiliations
Corresponding author
Additional information
This work was supported by Ministerio de Economía y Competitividad through Project TRA2016-78717-R.
Carlos GUARDIOLA received the M.Sc. degree in Mechanical Engineering from the Universitat Politècnica de València (Spain) in 2000, and was honored with the First National Award by the Spanish Education Ministry. He received the Ph.D. degree in 2005 at the same university, and he develops his research activity in the CMT-Motores Térmicos institute of the same university, where he serves now as Associate Professor, teaching Internal Combustion Engines. He leads research on control and diagnosis of internal combustion engines, and has been co-author of more than 100 scientific works, including books, patents and journal and conference papers. He was co-editor of “Automotive Model Predictive Control: Model, Methods and Applications”, and is member of SAE, of the Technical Committee on Automotive Control of the International Federation of Automatic Control, and of the Editorial Board of the “Proceedings of the Institution of Mechanical Engineers–Part D: Journal of Automobile Engineering”. In 2014 he received the Ralph R Teetor Educational Award by SAE International.
Benjamín PLA received his degree in Industrial Engineering (with focus on Mechanical Engineering) at the Universitat Politècnica de València in 2004. Afterwards, he enrolled the Research Institute CMT-Motores Térmicos to obtain a Ph.D. in 2009. During this process he passed through different research grants until obtaining a Lecturer position in 2008. After his Ph.D. he become assistant professor, giving lectures on Thermodynamics and Fluid-Mechanics in the Aerospace Degree of the UPV. With regards to research activities he is part of the Engine Control Research Group at CMT-Motores Térmicos. His research focuses on the control and diagnosis of vehicle powertrains.
Antonio GARCÍA received his Master’s degree in Energy Engineering (in 2005), Master’s degree in Internal Combustion Engines (in 2008) and Ph.D. Mechanical Engineer (in 2009) at the Universitat Politécnica de Valéncia (UPV). During the last years, his research activities have focused in the field of internal combustion diesel engines. He was promoted to Assistant Professor in June 2008 at the UPV, where he is developing his teaching responsibilities in the frame of combustion fundamentals. Nowadays, he is participating in different research activities as a member of the CMT-Motores Térmicos institute.
Vicente BORONAT received his Master’s degree in Mechanical Engineering (in 2014) and Ph.D.-Student Mechanical Engineer (in 2015) at the Universitat Politécnica de Valéncia. During the last years, his research activities have focused in the field of low temperature combustion strategies such as RCCI applied on internal combustion diesel engines. Nowadays, he is participating in Dual-Mode research activities as a member of the CMT-Motores Térmicos institute.
Rights and permissions
About this article
Cite this article
Guardiola, C., Pla, B., García, A. et al. Optimal heat release shaping in a reactivity controlled compression ignition (RCCI) engine. Control Theory Technol. 15, 117–128 (2017). https://doi.org/10.1007/s11768-017-6155-5
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11768-017-6155-5