Skip to main content
SpringerLink
Log in

Die steel surface layer quality improvement in titanium μ-powder mixed die sinking electrical discharge machining

  • ORIGINAL ARTICLE
  • Published:
The International Journal of Advanced Manufacturing Technology Aims and scope Submit manuscript

Abstract

In practice, the improvement of surface roughness (SR) after die sinking electric discharge machining (EDM) is simple and inexpensive when compared with the microhardness of machined-surface layers (HV). In addition, when HV is low, the improvement of SR will be less effective and have no significance to the mold surface layer. Therefore, the HV of molds after die sinking EDM is improved and plays a more important role than the improvement of SR. Currently, powder-mixed die sinking EDM is a technological solution that can improve both the HV and SR simultaneously. However, SR is given a priority criterion popular choice for many studies into powder-mixed die sinking EDM. In this current study, the researchers improve the quality of the steel surface layer of the mold using titanium (Ti) powder-mixed die sinking EDM. In the research, HV is selected as a criterion to optimize input parameters, and SKD61, SKD11, and SKT4 mold steels as well as Cu and Gr electrode materials are used. The effects of the workpiece material (A), electrode material (B), electrode polarity (C), pulse-on time (D), pulse-off time (F), current (E), Ti powder concentration (G), and some interactive A × B, A × G, and B × G to HV surface layers are analyzed and evaluated. Finally, the Taguchi method is used to optimize the parameters. Results indicated that parameters such as the electrode material, the pulse-on time, the concentration powders, A × G, and B × G significantly affect the HV. The Ti powder concentration has the largest effect on HV. When the powder concentration increased, HV was increased; its largest increase was 41.81%, and the optimal value of HVopt = 864.363 ± 61.68 HV at a Ti powder concentration of 10 g/l. The machined surface analysis of SEM and SR after powder-mixed die sinking EDM using Ti powder at optimal conditions showed that the quality of the surface layer was significantly improved. The qualities of surface layers, such us mechanical properties, topography, and the microstructure after EDM with titanium powder mixed into dielectric fluid, was significantly improved under optimal conditions for various mold steels.

This is a preview of subscription content, log in via an institution to check access.

Access this article

Log in via an institution

Price excludes VAT (USA)
Tax calculation will be finalised during checkout.

Instant access to the full article PDF.

Institutional subscriptions

Similar content being viewed by others

References

  1. Klocke F, Schneider S, Ehle L, Meyer H, Hensgen L, Klink A (2016) Investigations on surface integrity of heat treated 42CrMo4 (AISI 4140) processed by sinking EDM. Procedia CIRP 42:580–585

    Article  Google Scholar 

  2. Sidhom H, Ghanem F, Amadou T, Gonzalez G, Braham C (2013) Effect of electro discharge machining (EDM) on the AISI316L SS white layer microstructure and corrosion resistance. Int J Adv Manuf Technol 65(1):141–153

    Article  Google Scholar 

  3. Bleys P, Kruth JP, Lauwers B, Schacht B, Balasubramanian V, Froyen L, Humbeeck J (2006) Surface and sub-surface quality of steel after EDM. Adv Eng Mater 8:15–25

    Article  Google Scholar 

  4. Anand P, Shankar S (2010) Current research trends in variants of electrical discharge machining: a review. Int J Eng Sci Technol 2:2172–2191

    Google Scholar 

  5. Talla G, Gangopadhayay S, Biswas CK (2016) State of the art in powder mixed electric discharge machining: a review. Proc Inst Mech Eng B J Eng Manuf 231:2511–2526. https://doi.org/10.1177/0954405416634265

    Article  Google Scholar 

  6. Sanjeev K, Rupinder S, Singh TP, Sethi BL (2009) Surface modification by electrical discharge machining: a review. J Mater Process Technol 209:3675–3687

    Article  Google Scholar 

  7. Amit K, Amitava M, Amit RD, Alok KD (2018) Performance evaluation of Al2O3 nano powder mixed dielectric for electric discharge machining of Inconel 825. Mater Manuf Process 33(9):986–995

    Article  Google Scholar 

  8. Ahmed AK, Samir A, Saad MA (2016) The effect of SiC powder mixing electrical discharge machining on white layer thickness, heat flux and fatigue life of AISI D2 die steel. Engineering Science and Technology, an International Journal 19:1400–1415

    Article  Google Scholar 

  9. Bülent E, Fevzi U, Nihal E, Hamidullah Y (2015) Suspended SiC particle deposition on plastic die steel surfaces in powder mixed electrical discharge machining. Proc Inst Mech Eng B J Eng Manuf 229(3):475–486

    Article  Google Scholar 

  10. Anderson M, Fred LA, Paulo CS, Tiago C (2016) Surface modification of AISI H13 tool steel with silicon or manganese powders mixed to the dielectric in electrical discharge machining process. Int J Adv Manuf Technol 83(5):1057–1068

    Google Scholar 

  11. Wong YS, Lim LC, Iqbal R, Tee WM (1998) Near mirror finish phenomenon in EDM using powder mixed dielectric. J Mater Process Technol 79:30–40

    Article  Google Scholar 

  12. Hu FQ, Cao FY, Song BY, Hou PJ, Zhang Y, Chen K, Wei JQ (2013) Surface properties of SiCp/Al composite by powder mixed EDM. Procedia CIRP 6:101–106

    Article  Google Scholar 

  13. Katsushi F, Akinori S, Hideki T, Naotake M, Hidetaka M (2001) Accretion of titanium carbide by electrical discharge machining with powder suspended in working fluid. Precision Engineering Journal of the International Societies for Precision Engineering and Nanotechnology 25:138–144

    Google Scholar 

  14. Tzeng Y, Chen F (2005) Investigation into some surface characteristics of electrical discharge machined SKD11 using powder suspension dielectric oil. J Mater Process Technol 170:385–391

    Article  Google Scholar 

  15. Pichai J, Apiwat M (2012) Surface modification of tungsten carbide by electrical discharge coating (EDC) using a titanium powder suspension. Appl Surf Sci 258(19:7255–7265

    Google Scholar 

  16. Zakaria MZ, Mohammed BN, Ahsan AK, Mohammad YA (2014) Improving micro-hardness of stainless steel through powder mixed electrical discharge machining. Proc IMechE Part C: J Mechanical Engineering Science 228(18):3374–3380

    Article  Google Scholar 

  17. Sarabjeet SS, Ajay B, Sanjeev K (2014) Study of surface properties in particulate reinforced metal matrix composites (MMCs) using powder mixed electrical discharge machining (EDM). Mater Manuf Process 29:46–52

    Article  Google Scholar 

  18. Murahari K, Adepu K (2015) Effect of dielectric fluid with surfactant and graphite powder on electrical discharge machining of titanium alloy using Taguchi method. Engineering Science and Technology, an International Journal 18(4:524–535

    Google Scholar 

  19. Paulo P, Elsa H (2008) Effect of the powder concentration and dielectric flow in the surface morphology in electrical discharge machining with powder mixed dielectric (PMEDM). Int J Adv Manuf Technol 37:1120–1132

    Article  Google Scholar 

  20. Anirban B, Ajay B, Kumar N (2013) Surface characterization and material migration during surface modification of die steels with silicon. Graphite and tungsten powder in EDM process. J Mech Sci Technol 27(1):133–140

    Article  Google Scholar 

  21. Anirban B, Ajay B (2012) Effect of process variables on microhardness, grain size and strain during machining of various die steels with powder mixed electric discharge machining using dummy treated experimental design. Proc Inst Mech Eng B J Eng Manuf 226:1192–1204

    Article  Google Scholar 

  22. Kansal HK, Sehijpal S, Pradeep K (2007) Effect of silicon powder mixed EDM on machining rate of AISI D2 die steel. J Manuf Process 9(1):13–22

    Article  Google Scholar 

  23. Anirban B, Ajay B, Gurmail S, Singla VK (2012) Optimal parameter settings for rough and finish machining of die steels in powder mixed EDM. Int J Adv Manuf Technol 61:537–548

    Article  Google Scholar 

  24. Bülent E, Yusuf E (2012) How suspended particles affect surface morphology in powder mixed electrical discharge machining (PMEDM). Metall Mater Trans B 43(5):1138–1148

    Article  Google Scholar 

  25. Çogun C, Özerkan B, Karaçay T (2006) An experimental investigation on the effect of powder mixed dielectric on machining performance in electric discharge machining. Proc Inst Mech Eng B J Eng Manuf 220(7):1035–1050

    Article  Google Scholar 

  26. Chander P, Kansal HK, Pabla BS, Sanjeev P (2017) Experimental investigations in powder mixed electric discharge machining of Ti–35Nb–7Ta–5Zrβ-titanium alloy. Mater Manuf Process 32(3):274–285

    Article  Google Scholar 

  27. Katsushi F, Hiromichi S, Masayuki S (2009) Influence of electrical conditions on performance of electrical discharge machining with powder suspended in working oil for titanium carbide deposition process. Int J Adv Manuf Technol 40(11):1093–1101

    Google Scholar 

  28. Gangadharudu T, Gangopadhyay S, Biswas CK (2016) Effect of powder suspended dielectric on the EDM characteristics of Inconel 625. J Mater Eng Perform 25(2):704–717

    Article  Google Scholar 

  29. Gunawan SP, Muslim M, Hamdi M, Kimiyuki M (2009) Effect of micro MoS2 powder mixed dielectric fluid on surface quality and material removal rate in micro-EDM processes. Transaction of the Materials Research Society of Japan 34:329–332

    Article  Google Scholar 

  30. Houriyeh M, Davoud MJ, Ahmed ADS, Mohd H (2016) State of the art in powder mixed dielectric for EDM applications. Precis Eng 46:11–33

    Article  Google Scholar 

  31. Pawade MM, Banwait SS (2013) A brief review of die sinking electrical discharging machining process towards automation. American Journal of Mechanical Engineering 1(2):43–49

    Article  Google Scholar 

  32. Kansal HK, Sehijpal S, Pradeep K (2007) Technology and research developments in powder mixed electric discharge machining (PMEDM). J Mater Process Technol 184:32–41

    Article  Google Scholar 

  33. Long BT, Phan NH, Cuong N, Vijaykumar SJ (2016) Optimization of PMEDM process parameter for maximizing material removal rate by Taguchi’s method. Int J Adv Manuf Technol 87(5):1929–1939

    Article  Google Scholar 

  34. Long BT, Phan NH, Cuong N, Toan ND (2016) Surface quality analysis of die steels in powder-mixed electrical discharge machining using titan powder in fine machining, Advances in Mechanical Engineering ; 8(7), https://doi.org/10.1177/1687814016657732.

  35. Long BT, Phan NH, Cuong N, Toan ND Characteristics optimization of powder mixed electric discharge machining using titanium powder for die steel materials. Proc IMechE Part E: J Process Mechanical Engineering 0(0) 1–18. https://doi.org/10.1177/0954408917693661

  36. Mishra BP, Routara BC (2018) Impact of induction hardened workpiece hardness on EDM performance. Mater Manuf Process 33(6):626–633

    Article  Google Scholar 

Download references

Funding

This research is funded by the Vietnam National Foundation for Science and Technology Development (NAFOSTED) under grant number “107.01-2017.303.”

Author information

Authors and Affiliations

  1. School of Mechanical Engineering, Hanoi University of Science and Technology, Hanoi, Vietnam

    Toan Duc Nguyen & Long Tien Banh

  2. Faculty of Mechanical Engineering, Hanoi University of Industry, Hanoi, Vietnam

    Phan Huu Nguyen

Authors
  1. Toan Duc Nguyen
    View author publications

    You can also search for this author in PubMed Google Scholar

  2. Phan Huu Nguyen
    View author publications

    You can also search for this author in PubMed Google Scholar

  3. Long Tien Banh
    View author publications

    You can also search for this author in PubMed Google Scholar

Corresponding author

Correspondence to Phan Huu Nguyen.

Rights and permissions

Reprints and permissions

About this article

Check for updates. Verify currency and authenticity via CrossMark

Cite this article

Nguyen, T.D., Nguyen, P.H. & Banh, L.T. Die steel surface layer quality improvement in titanium μ-powder mixed die sinking electrical discharge machining. Int J Adv Manuf Technol 100, 2637–2651 (2019). https://doi.org/10.1007/s00170-018-2887-8

Download citation

  • Received:

  • Accepted:

  • Published:

  • Issue Date:

  • DOI: https://doi.org/10.1007/s00170-018-2887-8

Keywords

Search

Navigation