Abstract
In order to examine the relationship between the microstructure and the corrosion behavior in chloride solution, the microstructure of AlSi10Cu (Fe) sand cast aluminum alloy has been investigated by using different techniques including scanning electron microscopy, energy-dispersive spectroscopy, X-ray diffraction analysis and electrochemical measurements. The microscopic analysis and X-ray diffraction analysis show several phases in addition to matrix phase, including pores and phases at nano- and microscales. The average rate of micropores and nanopores is 4% and 5%, respectively. The nanoparticle size varies between 20 and 150 nm. Plates and corals-like silicon eutectic, rich-Cu phase and Chinese script phase (Al15(Mn,Fe)3Si2) have been observed. Energy-dispersive spectroscopy analyses show the presence of a new phase (Cu61.22 Zn25.39Ni11.85 Al1.54), and the pitting corrosion has been demonstrated to be initiated at the nanopores. The electrochemical measurements exhibited the effect of several elements and porosities on the corrosion kinetics that is controlled by charge transfer and diffusion phenomenon. Wide passive windows, followed by the breakdown of passive film and excessive dissolution, have been observed in 0.3 and 3 wt% NaCl solutions. The electrochemical measurements show a high corrosion rate which does not recommend the use of this alloy in seawater.
Similar content being viewed by others
References
Ahn SS, Pathan S, Koo JM, Baeg CH, Jeong CU, Son HT, Kim YH, Lee KH, Hong SJ (2018) Enhancement of the mechanical properties in Al–Si–Cu–Fe–Mg alloys with various processing parameters. Materials 11:2150. https://doi.org/10.3390/ma11112150
Al-Hella A, Kawther WA (2013) New approaches to casting hypereutectic Al–Si Alloys to achieve simultaneous refinement of primary silicon and modification of eutectic silicon, a thesis submitted for the degree of doctor of philosophy, Brunel center for advanced solidification technology (BCAST), Brunel university
Allachi H, Chaouket F, Draoui K (2010) Protection against corrosion in marine environments of AA6060 aluminium alloy by cerium chlorides. J Alloys Compd 491:223–229. https://doi.org/10.1016/j.jallcom.2009.11.042
Ambat R, Davenport AJ, Scamans GM, Afseth A (2006) Effect of iron-containing intermetallic particles on the corrosion behaviour of aluminium. Corros Sci 48:3455–3471. https://doi.org/10.1016/j.corsci.2006.01.005
Ammar HR, Samiel AM, Samuel FA (2008) porosity and fatigue behavior of hypoeutectic and hypereutectic aluminum-silicon casting alloy. Int J Fatigue 30:1024–1035. https://doi.org/10.1016/j.ijfatigue.2007.08.012
Bannour S, Abderrazak K, Mattei S, Masse JE, Autric M, Mhiri H (2013) The influence of position in overlap joints of Mg and Al alloys on microstructure and hardness of laser welds. J Laser Appl 25:032001. https://doi.org/10.2351/1.4792615
Barr TL (1977) ESCA studies of naturally passivated metal foils. J Vac Sci Technol 14:660–665. https://doi.org/10.1116/1.569174
Barrirero J, Pauly C, Engstler M, Ghanbaj J, Ghafoor N, Lin J, Schumacher P, Odén M, Mücklich F (2019) Eutectic modification by ternary compound cluster formation in Al–Si alloys. Sci Rep. https://doi.org/10.1038/s41598-019-41919-2
Berlanga-Labari C, Biezma-Moraleda MV, Rivero PJ (2020) Corrosion of cast aluminum alloys: a review. Metals 10:1–29. https://doi.org/10.3390/met10101384
Bessone JB, Salinas DR, Mayer Ebert CE, Lorenz WJ (1992) An EIS study of aluminium barrier-type oxide films formed in different media. Electrochim Acta 37:2283–2290. https://doi.org/10.1016/0013-4686(92)85124-4
Birbilis N, Buchheit RG (2005) Electrochemical characteristics of intermetallic phases in aluminum alloys. J Electrochem Soc 152:B140. https://doi.org/10.1149/1.1869984
Bogdanoff T, Seifeddine S, Dahle AK (2016) The effect of Si content on microstructure and mechanical properties of Al–Si alloy. La Metall Ital 108:65–69
Cáceres CH, Svensson IL, Taylor JA (2003) Strength-Ductility behaviour of Al-Si-Cu-Mg casting alloy in T6 temper. Int J Cast Met Res 15:531–543. https://doi.org/10.1080/13640461.2003.11819539
Campbell J, Castings (2003) the new metallurgy of cast metals. 2nd edn, Oxford
Cecchel S, Cornacchia G, Gelfi M (2017) Corrosion behavior of primary and secondary AlSi high pressure die casting alloys. Mater Corros 68:961–669. https://doi.org/10.1002/maco.201709526
Ceschini L, Morri A, Morrin A, Toschi S, Johansson S, Seifeddine S (2015) Effect of microstructure and overaging on the tensile behavior at room and elevated temperature of C355-T6 cast aluminum alloy. Mater Des 83:626–634. https://doi.org/10.1016/j.matdes.2015.06.031
Dinnis CM, Taylor JA, Dahle AK (2006) Interactions between iron, manganese, and the Al–Si eutectic in hypoeutectic Al–Si alloys. Metall and Mater Trans A 37:3283–3291. https://doi.org/10.1007/BF02586163
Djurdjevic M, Stockwell T, Sokolowski J (1999) The effect of strontium on the microstructure of the aluminium–silicon and aluminium–copper eutectics in the 319 aluminium alloy. Int J Cast Met Res 12:67–73
Dobkowska A, Adamczy K, Cieślak D, Mizera B, Kurzydłowski KJ, Kiełbus A (2016) The comparison of the microstructure and corrosion resistance of sand cast aluminum alloys. Arch Metall Mater 61:209–212. https://doi.org/10.1515/amm-2016-0038
Elzanaty H (2015) Effect of composition on the microstructure, tensile and hardness properties of Al–xSi alloys. J Mater Sci Surf Eng 2:126–129
Fernandes JCS, Travassos MA, Leitão E, Rangel CM, Barbosa M, Ferreira MGS (1989) the influence of Li on the electrochemical behaviour of pure aluminium. Portugaliae Electrochimica Acta 7:119–122
Ferreira IL, Lins JFC, Moutinho DJ, Gomes LG, Garcia A (2010) Numerical and experimental investigation of microporosity formation in a ternary Al–Cu–Si alloy. J Alloys Compd 503:31–39. https://doi.org/10.1016/j.jallcom.2010.04.244
Frers SE, Stefenel MM, Mayer C, Chierchie T (1990) AC-Impedance measurements on aluminium in chloride containing solutions and below the pitting potential. J Appl Electrochem 20:996–999. https://doi.org/10.1007/bf01019578
Hossain A, Gulshan F, Kurny ASW (2015) Electrochemical corrosion behavior of Ni-containing hypoeutectic Al–Si alloy. J Electrochem Sci Eng 5:173–179. https://doi.org/10.5599/jese.174
Jafarzadeh K, Shahrabi T, Oskouei AA (2009) novel approach using EIS to study flow accelerated pitting corrosion of AA5083-H321 aluminium-magnesium alloy in NaCl. J Appl Electrochem 39:1725–1731. https://doi.org/10.1007/s10800-009-9867-5
Jia Q, Li D, Li S, Zhang Z, Zhang N (2018) High-temperature oxidation resistance of NiAl intermetallic formed in situ by thermal spraying. Coatings 8:292. https://doi.org/10.3390/coatings8080292
Jiang W, Fan Z, Dai T, Li C (2014) Effects of rare earth elements addition on microstructures, tensile properties and fractography of A357 alloy. Mater Sci Eng A 597:237–244. https://doi.org/10.1016/j.msea.2014.01.009
Kuchariková L, Liptáková T, Tillová E, Bonek M, Medvecká D (2020) Corrosion behaviour correlation of the secondary aluminium casts in natural atmosphere and laboratory conditions. Arch Metall Mater 65:1455–1462. https://doi.org/10.24425/amm.2020.133713
Li Z, Samuel AM, Samuel FH, Ravindran C, Valtierra S (2003) Effect of alloying elements on the segregation and dissolution of Al2Cu phase in Al–Si–Cu 319 alloys. J Mater Sci 38:1203–1218. https://doi.org/10.1023/A:1022857703995
Ma P, Jia Y, Prashanth K, Yu Z, Li C, Zhao J, Yang S, Huang L (2017) Effect of Si content on the microstructure and properties of Al–Si alloys fabricated using hot extrusion. J Mater Res 32:2210–2217. https://doi.org/10.1557/jmr.2017.97
Mathers G (2002) The welding of aluminium and its alloys. CRC Press, Cambridge
Mbuya TO, Odera BO, Ng’ang’a SP (2003) Influence of iron on castability and properties of aluminium silicon alloys:literature review. Int J Cast Met Res 16:451–465. https://doi.org/10.1080/13640461.2003.11819622
McAlister AJ, Murray JL (1987) The (Al−Mn) aluminum-manganese system. J Phase Equilib 8:438–447
Michna S, Lukac I, Louda P, Ocenasek V, Schneider H, Drapala J, Koreny R, Miskufova A (2007) Aluminum materials and technologies from A to Z, Adin, s.r.o.Presom, Czech Republic
Mohamed AMA, Samuel FHA (2012) Review on the heat treatment of Al–Si–Cu/Mg casting alloys, heat treatment-conventional and novel applications. InTech: Rijeka, Croatia. https://doi.org/10.5772/79832
Munoz AG, Bessone JB (1999) Pitting of aluminium in non-aqueous chloride media. Corros Sci 41:1447–1463. https://doi.org/10.1016/S0010-938X(98)00199-1
Oya Y, Kojima Y, Hara N (2013) Influence of silicon on intergranular corrosion for aluminum alloys. Mater Trans 54:1200–1208. https://doi.org/10.2320/matertrans.M2013048
Pourbaix M (1974) Atlas of electrochemical equilibria in aqueous solutions. National Association of Corrosion Engineers, Houston
Reardon AC (2011) Metallurgy for the non-metallurgist, 2nd edn. ASM International, Materials Park
Rossi S, Eyraud M, Vacandio F, Massiani Y (2007) Corrosivity of long-term fire retardant Fire Trol (R) 931 and Fire Foam (R) 103 on aluminium alloys and steel. Mater Chem Phys 105:260–267. https://doi.org/10.1016/j.matchemphys.2007.04.055
Roy N, Samuel AM, Samuel FH (1996) Porosity formation in Al-9 wtpct Si-3 wtpct Cu alloy systems: metallographic observations. Metall and Mater Trans A 27:415–429. https://doi.org/10.1007/bf02648419
Samuel EH, Samuel AM, Doty HW (1997) Factors controlling the type and morphology of Cu-containing phases in 319 Al alloy. Trans Am Foundry Men’s Soc 30:893–801. https://doi.org/10.1080/13640461.1999.11819344
Seri O, Furuya S, Soga N (1989) Effect of copper content on corrosion of aluminum. J Jpn Inst Light Met 39:724–729. https://doi.org/10.2464/jilm.39.724
Singh S, Goel DB (1990) Influence of thermomechanical ageing on tensile properties of 2014 aluminium alloy. J Mater Sci 25:3894–3900. https://doi.org/10.1007/bf00582456
Sjölander E, Seifeddine S (2010) The heat treatment of Al–Si–Cu–Mg casting alloys. J Mater Process Technol 210:1249–1259. https://doi.org/10.1016/j.jmatprotec.2010.03.020
Skoko Ž, Popović S, Štefanić G (2009) Microstructure of Al–Zn and Zn–Al Alloys. Croat Chem Acta 82:405–420
Stadler F, Antrekowitsch H, Fragner W, Kaufmann H, Uggowitzer PJ (2011) The effect of Ni on the high-temperature strength of Al–Si cast alloys. Mater Sci Forum 690:274–277. https://doi.org/10.4028/www.scientific.net/MSF.690.274
Stadler F, Antrekowitsch H, Fragner W, Kaufmann H, Uggowitzer PJ (2012) Effect of main alloying elements on strength of Al–Si foundry alloys at elevated temperatures. Int J Cast Met Res 25:215–224. https://doi.org/10.1179/1743133612Y.0000000004
Taylor JA (1995) Metal-related castability effects in aluminium foundry alloys. Cast Metals 8:225–252. https://doi.org/10.1080/09534962.1996.11819212
Taylor JA (2004) The effect of iron in Al-Si casting alloys. In: 35th Australian Foundry Institute National conference, Adelaide, South Australia 148
Tenekedjiev N, Gruzleski JE (1990) Hypereutectic aluminium-silicon casting alloys—a review. Cast Met 3:96–105. https://doi.org/10.1080/09534962.1990.11819026
Tillov E, Chalupov M, Hurtalov L (2012) Evolution of phases in a recycled Al–Si cast alloy during solution treatment. Scan Electron Microsc. https://doi.org/10.5772/34542
Warmuzek M (2004) Aluminum-silicon casting alloys: Atlas of microfractographs. ASM International Materials Park, Ohio
Ye HZ (2003) An overview of the development of Al–Si-alloy based material for engine applications. J Mater Eng Perform 12:288–297. https://doi.org/10.1361/105994903770343132
Yoo YH, Park IJ, Kim JG, Kwak DH, Ji WS (2011) Corrosion characteristics of aluminum alloy in bio-ethanol blended gasoline fuel: Part 1. The corrosion properties of aluminum alloy in high temperature fuels. Fuel 90:1208–1214. https://doi.org/10.1016/j.fuel.2010.10.058
Zaid B, Saidi D, Benzaid A, Hadji S (2008) Effects of pH and chloride concentration on pitting corrosion of AA6061 aluminum alloy. Corrosion Sci 50:1841–1847. https://doi.org/10.1016/j.corsci.2008.03.006
Zamani M, Seifeddine S, Jarfors AE (2015) High temperature tensile deformation behavior and failure mechanisms of an Al–Si–Cu–Mg cast alloy—the microstructural scale effect. Mater Des 86:361. https://doi.org/10.1016/j.matdes.2015.07.084
Zazi N (2013) Effect of heat treatments on the microstructure, hardness and corrosion behavior of nondendritic AlSi9Cu3(Fe) cast alloy. Mater Sci (Medžiagotyra) 19:258–263. https://doi.org/10.5755/j01.ms.19.3.1397
Zazi N, Bouabdallah A, Aaboubi O, Chopart JP (2010) Pretreatment effects on the electrochemical responses for aluminium–magnesium alloy AA5083 corrosion behavior. Solid State Electrochem 14:1705–1711. https://doi.org/10.1007/s10008-010-1021-0
Author information
Authors and Affiliations
Corresponding author
Additional information
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.
Rights and permissions
About this article
Cite this article
Korichi, B., Zazi, N., Delbrel, S. et al. Microstructural, morphological characterization and corrosion behavior of sand cast AlSi10Cu(Fe) alloy in chloride solution. Chem. Pap. 76, 2947–2967 (2022). https://doi.org/10.1007/s11696-022-02064-9
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11696-022-02064-9